Maytag Atlantis Dryer Parts

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

The Timer Knob is an OEM replacement part for Whirlpool dryers. It allows users to set cycle durations with smooth, intuitive adjustment.

Symptoms of a faulty timer knob include:  

• The timer knob does not turn or is difficult to turn.
• The timer knob is missing

Causes of a bad timer knob can include loose or stripped internal gears from an extended operation or impact damage during loading/unloading clothes. 

Note: This is the center portion of the knob only. For the complete knob assembly, the cap and skirt must also be purchased.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This tub-to-pump hose connects the washer's outer tub to the drain pump, carrying water out of the machine during the drain cycle. Replacing a cracked or clogged hose can help stop leaks and restore consistent draining.

• Connects the washer's outer tub to the drain pump
• Transfers wash water to the pump during drain cycles
• A damaged or obstructed hose may cause leaks under the machine or slow/no draining
• Visible splits, soft spots, or kinks indicate the hose should be replaced

• Disconnect power and turn off water supply; protect the area with towels or a shallow pan
• Access the pump area; note hose routing and clamp positions before removal
• Inspect and clear the tub outlet and pump inlet; seat the new hose fully and secure with clamps
• Run a brief fill/drain test and check carefully for leaks before reassembly

This brake spring restores proper tension in the washer's transmission brake so the basket stops promptly and releases cleanly for spin. Replacing a fatigued or broken spring helps bring back smooth, reliable spin and stopping performance.

• Maintains brake tension to hold the basket stationary between cycles
• Releases the brake during spin so the basket can reach proper speed
• Helps stop the basket smoothly at cycle end
• Common signs include no/slow spin, basket coasting too long after spin, or brake squeal/grinding when stopping

• Disconnect power and water before servicing; wear gloves and eye protection.
• The brake spring is under tension—secure the assembly and carefully relieve spring force before removal.
• Access typically requires removing drive components to reach the brake assembly; support the washer safely if tilted.
• After installation, hand-rotate the drive pulley to ensure smooth brake engagement and release before running a test cycle.

This timer controls the sequence and duration of your washer's cycles. When its internal contacts wear or stick, the machine can stall or fail to advance. Replacing it restores reliable, automatic cycle progression.

• Advances the washer through fill, wash, rinse, drain, and spin in the programmed order
• Sends power to the water inlet valves, drive motor, and drain pump at the correct times
• Common symptoms include a cycle that won't advance, stops mid-cycle, or only progresses when the knob is turned by hand
• Also causes cycles to skip steps or run much longer/shorter than expected

• Disconnect power and shut off water before servicing
• Open the control console; remove the rear panel/cover to access the timer
• Move wires from the old timer to the new unit one at a time to maintain placement; secure the timer with its mounting screws
• Reinstall the dial/knob if applicable, reassemble the console, and run a test cycle to operation

This hinge bushing is the low-friction sleeve the hinge pin pivots in. Replacing a worn bushing restores smooth, quiet door or lid movement, keeps alignment true, and helps the appliance close cleanly while reducing hinge wear.

• Provides a smooth pivot surface between the hinge pin and bracket
• Helps maintain alignment so the door or lid closes flush
• Reduces squeaking, grinding, or binding when opening/closing
• Replaces cracked, flattened, or missing bushing that can cause sagging or scraping

• Disconnect power (and water supply if applicable) before servicing.
• Support the door or lid before removing hinge fasteners; note the order of spacers/washers.
• Remove the worn bushing, seat the new bushing fully, and reassemble in the same orientation.
• Inspect the hinge pin and bracket for wear; replace related parts if they are damaged.

This spring-timer knob replaces a worn, cracked or missing timer knob so you can set and adjust the appliance's mechanical timer reliably. Simple, direct replacement that restores the user control interface. What it does:

• Fits onto the appliance's mechanical timer shaft to allow setting and advancing the timer
• Restores a secure grip and pointer for accurate time selection
• Commonly used to fix loose, cracked, stripped, or missing timer knobs
• Helps resolve inability to turn or set the mechanical timer caused by a damaged knob

• Disconnect power to the appliance before starting any repair
• Pull the old knob straight off the timer shaft; align splines and press the new knob fully onto the shaft until seated
• If the knob is tight, use a proper knob puller or gentle, even leverage to avoid damaging the shaft

Mounting screw used to secure panels, trim, brackets, and small appliance components. Replace a missing or damaged fastener to restore proper fit, reduce vibration, and keep parts aligned for safe operation. What it does:

• Secures panels, control boards, brackets, and trim to maintain correct assembly
• Replaces stripped, broken, or missing screws that cause loose or rattling parts
• Helps prevent misalignment that can interfere with doors, knobs, or covers
• Standard fastener interface — use the correct driver and size for a secure fit

• Disconnect power and/or gas and follow appliance safety procedures before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to avoid damage to threads or surrounding parts
• If threads are damaged, replace the mating component or use the correct thread-repair method

Analog water temperature control board.

This tub bolt fastens the washer's inner tub to its hub/drive assembly, keeping the basket stable during agitation and spin. Replacing a worn or missing bolt restores a secure connection and helps reduce vibration and noise.

• Secures the spin basket to the drive hub/shaft
• Helps maintain proper tub alignment and stability
• Common fix for rattling, excessive vibration, or loose tub movement
• May prevent spin errors caused by a shifting basket connection

• Unplug the washer and shut off water supply before service
• Access is typically from the top by removing the agitator or washplate
• Use the correct socket/driver; do not over-tighten
• Inspect companion hardware (hub, spacer, washers) and replace if worn

This gasket seals the basket to the center shaft to help prevent leaks and reduce noise from worn or damaged seals. It restores a proper seal between the tub/basket and the drive shaft for reliable operation. What it does:

• Seals the gap between the basket/tub and the center drive shaft to help prevent water from leaking into the motor/tub area
• Helps reduce rubbing noise caused by a worn or torn seal
• Restores a tight fit after seal failure, wear, or damage
• Common symptom: water leakage from the tub area or visible wear around the shaft opening

• Refer to the exploded parts diagram for correct positioning and orientation
• Inspect mating surfaces for damage or residue and clean before installing the new gasket
• Replace only when the appliance is unplugged and water supply is turned off; follow safety procedures for draining and securing the unit
• If other components show wear (shaft seals, basket, or fasteners), replace them as recommended by the OEM

This locknut is a small threaded retaining nut used to secure rotating and stationary appliance components, helping keep assemblies tight and stable during operation. It prevents parts from loosening and reduces vibration-related issues. What it does:

• Secures shafts, pulleys, or fittings to prevent axial movement
• Keeps assemblies fastened under normal vibration and load
• Helps stop wobble, grinding, or part separation caused by a loose connection
• Works with the matching threaded stud, shaft, or fitting for a proper hold

• Disconnect power and follow appliance safety procedures before servicing
• Use the matching thread size and engage threads fully; hand-start before tightening
• Tighten securely without overtightening; use the correct driver or socket for the nut
• Inspect mating threads and replace if damaged

Spesc: #12 pozi - drive