Maytag Mvwx700xl2 Parts

Contains two, six foot long braided hoses with 90 degree ends.

This replacement nut is a small hardware fastener used to secure components inside your appliance. It helps keep parts tight and properly aligned so assemblies don't loosen from vibration or normal operation.

• Threads onto a mating bolt, stud, or shaft to clamp parts together
• Maintains alignment and reduces movement and rattling
• Replaces a stripped, missing, or damaged nut to restore a secure fit
• Common signs of failure: loose panels or components, unusual vibration/noise, hardware missing

• Disconnect power; shut off gas and/or water if applicable before servicing
• Note the original hardware stack-up (washers/spacers) and orientation for reassembly
• Start by hand to avoid cross-threading; tighten to manufacturer guidance—do not overtighten
• Replace any damaged washers or locking devices

Used from harness to top.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This plated control knob replaces a worn or missing knob on your range or cooktop, restoring smooth burner adjustment and a matching look. It pushes onto the existing control stem and operates like the original. What it does:

• Mounts on the burner control stem to set and adjust heat levels
• Replaces cracked, stripped, loose, or missing knobs to restore proper control
• Provides clear pointer orientation for consistent settings
• Symptoms it can help with: knob falls off, wobbly/loose feel, hard to turn, won't engage

• One plated control knob assembly

• Disconnect power and let the cooking surface cool; if applicable, turn off gas supply.
• Pull the old knob straight off the stem—avoid prying or side pressure that can damage the shaft.
• Align the new knob with the stem and press straight on until fully seated.
• Test the control for smooth operation before regular use.

Size: .20 Fl. Oz. (6 ml)

Screw: 8-16 x 3/8 inch.

This small tension spring restores the return force in the top lock mechanism so it latches securely and releases smoothly. Replacing a fatigued spring helps the lock operate consistently and keeps the panel/top properly secured.

• Provides the return/tension force for the lock lever or arm
• Helps the lock engage fully and stay secured under vibration
• Restores proper latch feel and consistent lock/unlock action
• Common signs include a loose/floppy lock, poor engagement, or the lock not returning to position

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Note the spring's routing/orientation before removal
• Use needle-nose pliers; mind sharp edges and pinch points
• After installation, manually check lock movement for smooth travel

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

Replace aging or leaking washer supply lines with this fill hose kit. It provides two 5-foot hoses to connect your home's hot and cold water valves to the washer, helping maintain a secure connection and consistent filling.

• Connects hot and cold water faucets to the washer's inlet valves
• Replace if hoses are leaking, cracked, bulging, or kinked
• Can help address slow filling caused by restricted or kinked hoses
• Useful when installing or relocating a washer

• Unplug the washer and shut off both water supply valves before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucet and washer
• Match hot to hot and cold to cold; hand-start threads to avoid cross-threading, then tighten firmly without overtightening
• Restore water and power; run a fill test and check all connections for leaks

This machine screw secures components in place to maintain proper alignment and stability during appliance operation. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Provides a secure mechanical fasten for panels, brackets, or internal assemblies
• Helps correct rattling, vibration, or loose-fitting parts
• Useful when an original screw is stripped, corroded, or lost
• Sized to match 8-18 thread applications in compatible units

• Disconnect power and shut off water or gas before servicing
• Note original screw location and orientation for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace any damaged clips or mounts the screw engages

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

5 foot. Package of 2.

This replacement 7-2-1 screw secures components in compatible Whirlpool appliances, providing a dependable fastener for panels and assemblies. Use it to restore proper fitment and reduce rattling or loose parts. What it does

• Fastens trim, panels, brackets, or internal assemblies to keep parts secure
• Helps stop vibration-related noise from loose components
• Restores correct mounting where the original screw is missing or damaged
• Matches the form and fit of the OEM fastener for intended attachment points

• One replacement 7-2-1 screw

• Use the correct driver to avoid stripping the screw head
• Hand-start threads before tightening to prevent cross-threading
• Tighten until snug—do not over-tighten to avoid damaging plastic or sheet-metal parts
• Disconnect power to the appliance before accessing internal areas

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

This replacement control knob lets you select settings and operate the appliance's controls with a secure grip and clear position index. Restores reliable user control when the original knob is cracked, loose, or worn. What it does:

• Replaces a damaged or missing control/selector knob so you can turn and set controls accurately
• Snaps onto the control shaft to provide a solid tactile stop and visible setting indicator
• Commonly used when the original knob is cracked, stripped, stiff, or spins on the shaft
• Matches OEM fit and rotation for proper function and alignment

• One control knob

• Remove power to the appliance before replacing the knob to avoid injury
• Pull the old knob straight off the control shaft and push the new knob onto the shaft until it seats
• If the knob will not fully seat, check for obstructions or a damaged shaft before forcing it