Need Help?
Call or text
Ground screw secures transmission housing and console components in washers. Replaces missing, stripped, or corroded screws. 10-24 x 3/8 inch fastener.
Replaced timer control unit, first time doing this. Read more
Secures the terminal block to your range's back panel. Replace if stripped, corroded, or missing to ensure safe electrical connections. 10-32 size.
Check the power cord connection to the stove and found burned cable due to loose connection. Replaced the terminal and the nuts and installed a new power cord. Read more
10-24 threaded machine screw secures panels, brackets, and internal assemblies in appliances. Replace missing, stripped, or damaged screws.
Supports the front of your dryer drum for smooth rotation. Replace when you hear scraping noises or the drum wobbles. Confirm fit with your model number.
First time DIY dryer repair. Videos very helpful! Remove front. Found glides worn thin, paint on drum removed where glides located. Drum, cage and motor turned easily - must be OK. Thirteen year old dryer. Order glides & felt, might as well replace belt and rollers while there. First time order - could not have been easier! Received 2nd day. Replaced parts, reassembled & connected power. Ran for 3 minutes with scraping noise then stopped with burning odor. Disassembled dryer, smelled odor from... Read more
Plastic retainer clip that secures the top cabinet panel to the washer chassis. Replace if cracked, broken, or missing to restore alignment and prevent rattling.
I replaced the fill valve assembly with a new one. Had to look carefully at the parts diagrams to make sure I ordered the right one since the serial number break old vs. new didn't seem to match the number on my machine. On this particular machine you don't need to pull it out too far from the wall-leave the hoses connected to the valve, remove the screw holding the valve bracket, and pull into the washing machine where you can easily access the hose ends. A putty knife is needed to open... Read more
Rear support assembly stabilizes your dryer's housing and aligns internal components. Replace if cracked, broken, or worn to prevent noise and vibration.
Replaced the roller and shaft. The roller had worn 1/4 of the way through the support shaft. Read more
If your dryer door or control switch is loose or misaligned, this retainer clip holds the switch securely in place for reliable operation. Simple fix.
Secures wire harness connections in your washer. Replace if clip is broken, cracked, or missing to prevent loose wiring. Verify fit with your model number.
Secures control panels, trim, and covers on your dryer. Replace missing, stripped, or corroded screws to restore proper fit and reduce rattling.
Replaced glass window on stove door. The hardest part was putting door back in place. You have to get the notch of hinge flush with frame before closing oven door! Read more
Replacement mounting screw for washer assembly. Secures components and panels in place. Order a new screw if yours is stripped, missing, or damaged.
Felt seal pad cushions and seals the dryer drum. Replace when worn, torn, or causing squeaking noises. Confirm fit with your model number.
Removed front wall of dryer, disconnected electrical from wall(first thing). Disconnect front door switch, remove tub, remove felt, clean, used compressed air to blow out all dust from heater assembly. Used compressed air to blow out all lint catch line parts. Used electrical contact cleaner to clean all electrical connections where dust and lint had gathered. Installed new felt pad by first applying high temp adhesive, let adhesive set about a minute or so, install felt. Let sit for about... Read more
Supports the front of the dryer drum for smooth rotation. Replace if drum is noisy, wobbling, or causes overheating. Verify fit with your model number.
New glides, idler had a crack, blower retaining ring was gone. And a good clean out. Like new again for 2 hours and $77.00 Read more
Replacement idler spring for dryers. Maintains tension on the idler pulley to keep the drum belt engaged. Replace if broken, stretched, or missing.
Usually ships within 4 - 14 days
If your dryer only runs on high speed or lost low/medium heat settings, the resistor assembly may have failed. Easy DIY fix for multi-speed issues.
Watched the videos, ran ohmmeter tests and zeroed in on the timer. Ordered a replacement timer on a Mon night and received it about noon on Thursday. Installed it same day. Problem solved. Great service. Read more
If your mixer's attachments or components feel loose or wobbly, this 10-24 lock nut secures threaded fasteners and prevents vibration loosening. Quick fix.
Front panel mounting clip for dryers. Secures the front panel to the machine frame. Replace if clip is cracked, broken, or missing to properly mount panel.