Mdb66601bt Parts

Color: Gray

Right hand side

This seal sits at the dishwasher's air/water inlet, creating a tight barrier where the inlet assembly meets the tub or door. Replacing a worn seal helps stop nuisance leaks and supports proper fill and venting performance. What it does

• Forms a watertight seal at the air/water inlet connection
• Helps prevent drips or seepage during fill and wash
• Supports correct venting to keep moisture contained inside the tub
• Common failure signs include water on the floor near the unit, dampness around the inlet/vent area, or a cracked, flattened, or brittle seal

• One air/water inlet seal

• Disconnect power and shut off water before servicing
• Access method varies by model; remove the inlet/vent cover or side panel to reach the seal
• Clean mating surfaces; seat the new seal evenly without distortion
• Reassemble and run a brief fill/wash to check for leaks

This control board housing secures and protects the washer's electronic control board, keeping circuitry stable and shielded from moisture and debris for reliable operation. It fits into the console area and supports proper control panel alignment. What it does:

• Holds and protects the electronic control board inside the console from impact, dust and moisture.
• Keeps the control board properly positioned for reliable electrical connections.
• Helps prevent control panel wobble or misalignment that can cause button or dial issues.
• Commonly replaced when housing is cracked, broken mounting tabs fail, or board access is needed.

• 1 control board housing

• Disconnect power and water to the appliance before beginning any repair.
• Handle the control board and housing carefully to avoid damage to connectors or circuit components.
• Use appropriate tools to remove console components; replace damaged mounting tabs and secure all fasteners.
• Discharge any capacitors and follow the board manufacturer's ESD/safety recommendations.

This replacement silverware basket holds forks, knives and spoons in the dishwasher lower rack so utensils stay upright and separate for better cleaning and easier unloading. It's a direct-fit interior basket designed to restore secure utensil loading. What it does:

• Keeps silverware and small utensils contained so pieces don't fall through or block the spray arms
• Separates items to improve water flow and cleaning coverage
• Prevents loose utensils from banging and potentially damaging dishes
• Replaces cracked, broken, or missing baskets that allow utensils to shift during the cycle

• Drop into the lower rack — no tools required for typical swap-out
• Position basket so it sits flat and does not interfere with rack movement or spray arm rotation
• Avoid overloading; place sharp utensils point-down or bundle separately to reduce hazard when unloading
• For appliance repairs beyond simple replacement, disconnect power and water before servicing

This chopper assembly replaces the food-chopping component in compatible countertop food processors, restoring even chopping and diced results. It helps get blades turning and keeps food processing performing as intended. What it does:

• Spins and chops food inside the processor bowl for consistent results
• Restores proper cutting when chopping is uneven or not happening
• Helps eliminate food buildup that causes noisy or inefficient operation
• Works with the existing drive coupling to transfer motor power to the blades

• Disconnect power and remove the processor bowl and lid before servicing
• Handle blades carefully — they are sharp; wear cut-resistant gloves
• Ensure the part seats fully on the drive coupling and locks into place before use
• Test operation with small amounts of food after reassembly; stop immediately if unusual noise or resistance occurs

This replacement rack track restores smooth, stable rack movement and keeps the oven rack aligned while sliding in and out. It helps prevent rack sagging, binding, or uneven travel so food and cookware stay level and secure. What it does

• Guides and supports the oven rack so it slides in and out smoothly.
• Prevents racks from sagging, tipping, or binding when pulled forward.
• Restores proper rack alignment to reduce scraping, catching, or loud banging.
• Works with standard oven/range racks that use a molded metal/plastic track system.

• High-level swap: remove the oven racks, unfasten the old track, and secure the replacement in the same mounting locations.
• Use appropriate hand tools and avoid forcing parts; aligning the track before tightening fasteners reduces binding.
• Disconnect power to the appliance or follow the manufacturer's safety guidance if servicing components near electrical connections.

Color: Gray

This manifold mounting bracket secures the gas manifold assembly to the appliance frame, keeping fuel lines and related components aligned for reliable operation. It's a direct-fit replacement that restores proper manifold support. What it does:

• Holds the gas manifold in the correct position to prevent strain on connections and lines
• Helps maintain stable alignment of valves and supply tubing to reduce leaks and intermittent flow
• Addresses symptoms like a loose or rattling manifold assembly or visible bracket damage
• Restores proper mounting after impact or corrosion-related bracket failure

• One manifold mounting bracket

• Install only with the appliance powered off and gas supply completely shut; follow local codes
• Match bracket orientation to the original and secure with manufacturer-specified fasteners
• Inspect nearby tubing, fittings and valve mounts for damage when replacing the bracket

A filter guard that helps keep debris away from the wash pump and drain area, protecting the pump and improving drain performance. Simple replacement for worn or damaged filter housings. What it does:

• Covers and protects the dishwasher's lower filter area to help prevent large debris from entering the pump
• Helps reduce clogs and poor drain performance caused by food or loose items
• Maintains proper water flow through the filter assembly for more reliable operation
• Works as a replacement for a cracked, warped, or missing filter guard that leaks or allows debris through

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove the lower rack and existing filter assembly to access the guard
• Inspect adjacent filter parts for wear; replace damaged components to ensure proper sealing
• Hand-tighten or seat parts as directed by the OEM; avoid forcing or overtightening plastic components

A stainless pushnut used to secure shafts, studs, or small components with a quick, push-on retainer that resists corrosion. Keeps parts fastened without threading or additional hardware for a clean, low-profile fit. What it does:

• Acts as a push-on retaining nut to hold shafts, studs, or fittings in place
• Provides a corrosion-resistant stainless finish for wet or high-humidity areas
• Prevents components from sliding off axles or posts during normal operation
• Commonly used on control shafts, knobs, or small internal assemblies

• Turn power off and unplug appliance before servicing to avoid shock or injury
• Push onto the post or shaft until fully seated; a firm press or light tap may be required
• Use appropriate hand tools or pliers with protection to avoid damaging the part
• Replace with identical part number to ensure fit and function

This snap-in outlet connector secures wiring to an appliance control or harness and restores a reliable electrical contact. Designed for a direct, tool-assisted snap fit, it helps eliminate loose or intermittent connections. What it does:

• Provides a secure snap-in electrical connection between wiring and the appliance harness or control
• Restores power flow when a worn or damaged outlet causes intermittent operation or no power
• Prevents arcing and poor contact that can result from loose terminals
• Matches OEM fit for straightforward replacement when the original snap outlet is broken or missing

• Disconnect power to the appliance before inspecting or replacing electrical parts
• Remove access panels as required to reach the outlet; replacement typically snaps into place
• Verify correct orientation and full seating of the connector to ensure a solid contact
• If corrosion or wiring damage is present, replace or repair wiring per OEM guidance