Mgr575oadw Parts

This oven rack restores a smooth-sliding, level surface for cookware inside your range or wall oven. Replace a bent, rusty, or peeling rack to maintain safe support, proper spacing, and full oven capacity. What it does:

• Supports bakeware and food at the correct height during baking, roasting, and broiling
• Slides on the oven's side supports for easy loading and removal
• Helps maintain proper spacing and airflow when using multiple racks
• Replace if the rack is bent/warped, rusted, finish is flaking, or it no longer slides or sits level

• 1 oven rack

• Disconnect power and allow the oven to cool completely before servicing
• To remove, open the door, lift the rack's front edge slightly, and pull straight out; reverse to install
• For tight clearances, removing the oven door may help
• Many manufacturers recommend removing racks before a self-clean cycle to protect the finish

Color: black. Small size. Measures about 2-1/2 inches in diameter.

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

This factory fastener secures panels, trim, or brackets on your appliance. Replacing a missing or stripped screw restores a snug, rattle-free fit and keeps components aligned for proper operation and a clean, finished appearance.

• Fastens exterior panels, trim pieces, or internal brackets to the appliance chassis
• Replaces lost, damaged, or stripped hardware
• Helps prevent vibration, rattling, and gaps between parts
• Common signs you need this screw: missing hardware, loose or misaligned panel/trim, stripped head or threads

• Disconnect power before servicing; also shut off the gas supply
• Use the correct driver; start the screw by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping or cracking adjacent parts
• Repair or replace the mounting point before installing

Color: Black. For biscuit order 98008169. For white order WP98008544.

This gas surface burner head sits on the burner base and channels gas through precision ports for quick ignition and an even flame. Replacing a worn or clogged head helps restore reliable lighting and consistent heat.

• Distributes gas from the burner base to the flame ports for even flame patterns
• Interfaces with the spark electrode to enable ignition
• Helps maintain proper flame shape and heat output
• Common symptoms include burner won't light, weak/uneven or yellow flames, delayed ignition, or continuous clicking

• Disconnect power and shut off the gas supply before servicing
• Remove grate and burner cap; lift the old burner head off the base
• Clean the burner base and electrode area; align the new head with locator pins and the electrode opening, then seat fully
• Reinstall cap and grate; restore gas/power and test ignition and flame

This drawer roller supports and guides the lower range drawer so it slides smoothly on its track. Replacing a worn or broken roller restores easy operation and helps prevent the drawer from binding, sagging, or coming off the track.

• Supports the storage/warming drawer as it opens and closes
• Helps keep the drawer aligned on the rails to prevent tilting or popping off
• Reduces friction for smoother movement and less noise
• Typical failure signs: sticking drawer, rough/grinding movement, sagging front, or a cracked/flat-spotted wheel

• Disconnect power and allow the appliance to cool completely
• Remove the lower drawer to access the rollers
• Detach the fastener or retainer, install the new roller in the same orientation, and secure it
• Reinstall the drawer and verify smooth travel and proper engagement on both tracks

Replace a damaged or discolored oven handle with this white door handle. It restores a secure, comfortable grip and a clean look so you can open and close your range or wall oven door with confidence.

• Provides the handhold used to open and close the oven door
• Replaces cracked, broken, loose, or missing handles
• Helps restore safe handling and original appearance
• White finish to match compatible models

• Disconnect power at the breaker and allow the oven to cool completely
• Support the door/outer glass; remove inner door screws to access the handle mounts
• Transfer any end caps or hardware from the old handle, if applicable
• Tighten fasteners evenly; reassemble and check door operation

This oven gas valve controls the flow of gas to the oven burner. When functioning properly, it allows the burner to ignite and maintain a steady flame for consistent preheating and baking performance.

• Opens and closes to supply gas to the oven burner as commanded by the control system
• Helps ensure gas only flows when ignition is called for
• Common symptoms include no heat/no flame, slow preheat, or temperature not reaching set point
• May also present as intermittent heat or a weak/irregular burner flame

• Disconnect power and shut off the gas supply before servicing
• Verify igniter condition/current; a weak igniter can mimic a failed valve
• Transfer any required fittings or brackets from the original valve
• Use gas-rated thread sealant on threaded joints; leak-test all connections and run a test cycle to proper ignition

Color: Black. Size: Large.

This LP Conversion Kit adapts a compatible gas appliance from natural gas to liquid propane, aligning regulator settings and burner orifice sizing so flames are correct and ignition is reliable for safe, efficient operation when installed per OEM instructions.

• Converts a natural-gas–configured unit to LP/propane per model specifications
• Helps address issues seen when an NG setup is run on LP: large or yellow flames, soot, uneven heating, or difficulty adjusting flame
• Supports proper regulator pressure and burner orifice sizing for steady ignition and flame
• Model-specific kit—use only on models that call for this part number

• Conversion should be performed by a qualified gas technician; follow the product's service manual and local codes
• Disconnect power and shut off gas before servicing; leak-test all fittings after conversion with an approved solution
• Adjust/convert the pressure regulator and replace/adjust burner orifices as instructed; complete burner flame and air-shutter adjustments
• Verify final flame characteristics on all burners and complete any required appliance labeling per manufacturer instructions

A shoulder screw that secures appliance components and provides a precise pivot or spacer point. Replaces a missing or worn screw to restore alignment, reduce rattling, and keep panels and assemblies securely in place. What it does:

• Provides a fixed-diameter shoulder for pivots, spacers, or mounting points in assemblies.
• Holds panels and moving components at the correct distance to prevent binding or friction.
• A missing or worn shoulder screw can cause misalignment, rattling, or loose parts during operation.
• Used where a smooth-bearing surface and controlled clearance are required between parts.

• Disconnect power to the appliance (unplug or shut off breaker) before servicing.
• Handle small fasteners carefully to avoid dropping into assemblies; magnetic pickup tools can help.
• Start threads by hand to avoid cross-threading; tighten snugly but avoid overtightening.

Color: White

Color: White. Size: 2 oz. can. Porcelain touch-up paint.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Replacement burner seal assembly that creates a sealed barrier between a sealed gas cooktop burner and the cooktop surface, helping keep spills and debris out of the burner area and restoring stable burner seating. What it does:

• Forms a gasketed seal around the burner to limit spills, crumbs, and moisture from entering the burner box.
• Helps maintain proper burner seating for consistent flame shape and heat distribution.
• Replace if the seal is torn, flattened, warped, or shows heavy discoloration from spills or heat.
• Can reduce burner ignition or flame irregularities caused by debris or a damaged seal.

• Disconnect power and shut off gas supply before servicing; allow the cooktop to fully cool.
• Remove burner cap and head per your model's service instructions before replacing the seal.
• Clean the surrounding area of grease and debris, then press the new seal into place so it seats evenly.