Mgr6775adb/Q/S/W Parts

Size: 8abx3/8 - blk)

This electronic control board manages the appliance's cycle selection, timing and user interface so the unit runs the programmed functions reliably. It replaces a failed control to restore responsive buttons, accurate cycles and display feedback. What it does:

• Regulates cycle selection, timing and start/stop commands for normal operation
• Communicates with sensors and components to control heating, motor and valve functions
• Replaces a faulty control that causes blank display, unresponsive controls or incorrect cycle behavior
• Helps correct intermittent power or error-code conditions tied to a failed control board

• Disconnect power to the appliance before any service to avoid shock or damage
• Handle the board by its edges and avoid touching circuitry; use anti-static precautions if available
• Verify wiring harness connections match the replacement before securing the new board

Color: black. It measures about 2 inches in diameter.

This door latch assembly secures and electrically locks the washer door so cycles can start and run safely. It replaces a worn or failed latch to restore proper door locking and cycle operation. What it does:

• Physically secures and aligns the washer door so it closes properly.
• Activates the door-lock switch so the machine can start and run.
• Helps prevent the door from opening mid-cycle, reducing leaks and interruptions.
• Commonly used when the washer won't start, shows a door-lock error, or the door won't stay closed.

• One complete door latch assembly.

• Disconnect power before starting any repair to avoid shock or injury.
• Remove the washer door boot or front panel to access the latch.
• Check wiring harness connections and connector orientation before reconnecting.
• After installation, run a short diagnostic or test cycle to ensure the latch locks and releases correctly.

This bake and broil valve controls gas flow to the oven's bake and broil burners so the oven heats when a temperature or function is selected. Replaces a failing valve to restore reliable oven heating. What it does:

• Directs gas to the bake and broil burners when the oven calls for heat
• Helps the oven reach and maintain set cooking temperatures
• Commonly replaced for no-heat, weak heat, or burner not igniting during bake/broil cycles
• Works as the primary safety/control valve for oven burner operation

• Turn off gas supply and power at the household shutoffs before servicing
• Minor disassembly of the oven front or manifold may be required; follow OEM service instructions
• Replace only with correct part number and check all gas line fittings for leaks after installation

This replacement right-side top burner tubing routes gas to the burner assembly and restores proper fuel flow for even ignition. Designed to match OEM fit, it helps resolve burner fuel delivery issues safely and reliably. What it does

• Replaces damaged or corroded right-side top burner tubing that can cause weak flame or failed ignition
• Restores a sealed gas path to prevent leaks and maintain consistent burner performance
• Helps eliminate clicking or delayed ignition caused by interrupted fuel flow
• Matches OEM routing and connection points for a direct replacement

• Two right-side top burner tubing pieces

• Install only if this tubing is specified for your model; verify orientation before starting
• Work with the gas supply turned off and follow local codes
• Check all fittings for tightness and test for leaks with a soap solution after installation
• Do not rig or modify tubing; use only approved replacement parts for gas connections

This mounting bracket secures internal appliance components to the cabinet or frame, restoring stable support and proper alignment for the attached assembly. It's a direct-fit replacement when the original bracket is bent, broken, or missing. What it does:

• Provides a solid attachment point to keep components aligned and secure
• Prevents vibration, rattling, or movement caused by a damaged or missing bracket
• Restores correct positioning for connected parts so they operate reliably
• Helps maintain sealing and clearance by holding panels or assemblies in place

• One mounting bracket as pictured

• Inspect surrounding fasteners and mounting points; replace any stripped screws or clips
• Use the same screw locations and hardware type as the original for proper fit
• Disconnect power and remove any nearby panels before accessing the bracket to avoid injury

This wire harness routes electrical power and signals between components to restore proper appliance operation. It replaces damaged or worn wiring to eliminate intermittent connections and reduce the risk of shorts. What it does:

• Connects motors, switches, sensors, and heaters so components receive power and signals
• Restores reliable electrical paths when original wiring is frayed, burnt, or broken
• Helps stop intermittent operation, failure-to-start symptoms, or components losing power
• Reduces risk of arcing or short circuits caused by damaged insulation or loose terminals

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing wiring
• Compare connectors and wire colors to the original harness to ensure correct fit before installing
• Route and secure wiring away from heat and moving parts; avoid pinching or sharp edges
• If you see melting, burning, or damaged terminals on mating parts, replace or repair those components too

This is a genuine replacement screw used to secure panels, brackets and components on compatible Whirlpool appliances. It restores proper fit and reduces rattling or loose parts for safer, quieter operation. What it does:

• Fastens and secures panels, trim, brackets or small components
• Stops rattling or vibration caused by missing or loose screws
• Restores proper alignment of removable panels and assemblies
• Provides the correct threaded fastening for a reliable repair

• Disconnect power (and water if applicable) before servicing the appliance
• Replace like-for-like: match screw length, thread and head type to the original
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening, which can strip threads or crack plastic