Mhw35005fw0 Parts

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Contains two, six foot long braided hoses with 90 degree ends.

This RFI noise filter conditions the AC power entering your microwave, reducing electrical interference and helping protect and stabilize the control and power circuits. Replace it if the unit is dead or trips a breaker when starting.

• Filters radio-frequency/electromagnetic noise on the incoming AC line
• Helps stabilize power to the control, relays, lights, and fans
• Failure may cause no display or intermittent loss of power
• A shorted filter may blow the line fuse or trip the household breaker when plugged in or when Start is pressed

• Disconnect power by unplugging the microwave or switching off the dedicated circuit breaker
• For over-the-range units, remove the microwave from the wall to safely access internal components
• Label and transfer wires to matching terminals; mount the filter securely and route wiring away from sharp edges

This replacement bracket secures a component within your appliance. It restores a firm, correctly aligned mounting point so parts stay stable and operate as intended without looseness, shifting, or vibration. What it does:

• Provides a rigid mounting point on the appliance frame or cabinet
• Holds the mating component in proper position and alignment
• Helps reduce rattles, vibration, and movement
• Replaces a bent, cracked, stripped, or missing bracket

• 1 bracket

• Disconnect power; turn off gas or water before servicing
• Note the original bracket's orientation and fastener locations before removal
• Install using appropriate screws/fasteners; do not overtighten
• Verify alignment and clearances, then test operation before final reassembly

This factory fastener secures appliance components such as panels, brackets, and handles. Replacing a missing or damaged screw restores a tight fit, reduces rattles, and helps keep parts aligned for smooth, reliable operation.

• Secures components to the appliance frame or assemblies
• Helps maintain alignment and structural stability
• Replaces missing, rusted, or stripped hardware
• Common symptoms include loose/wobbly handles or panels, rattling/vibration noises, or a visibly missing screw

• Disconnect power before servicing
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten; snug until secure
• Replace any that are corroded or stripped for an even hold

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

This replacement screw secures panels, brackets, and internal components in your appliance. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps keep parts properly aligned and protected during operation.

• Fastens appliance panels, brackets, and hardware in the designated locations
• Replaces missing, stripped, or corroded fasteners
• Helps reduce vibration noise and looseness from unsecured parts
• Restores proper fit and alignment after service or reassembly

• Disconnect power; turn off water supply before servicing
• Match the screw to the original location and replace one at a time to maintain alignment
• Use the correct driver; tighten snugly without overtightening to avoid stripping metal or cracking plastics
• If threads in the mating hole are damaged, repair/replace the clip or insert as specified in the service manual

This direct hose assembly routes water or drain flow to restore proper operation and stop leaks caused by cracked or worn tubing. Designed to replace a damaged hose and help prevent water damage and poor drainage. What it does:

• Directs water or drain flow between appliance components to maintain proper plumbing function.
• Stops leaks and reduces the chance of water pooling or unintended discharge from worn or cracked hoses.
• Common symptoms addressed: visible leaks, water under or around the appliance, slow or inconsistent draining.

• Disconnect power and shut off the water supply before starting any repairs.
• Inspect hose ends and connections for damage; replace clamps or seals if corroded or worn.
• Secure hose with appropriate clamps and route to avoid kinks or pinch points.
• After installation, restore power and water, run a short cycle, and check all connections for leaks.

This wire harness routes power and signals between an appliance's control and internal components to restore reliable electrical connections. Replacing a damaged harness helps stop intermittent operation and power loss for safer, more consistent performance. What it does:

• Routes power and control signals between the control board and internal components.
• Replaces frayed, cut, or burned wiring that can cause intermittent operation or component failures.
• Helps address symptoms such as loss of power to controls, unresponsive cycles, or devices that won't start.
• Prevents loose or corroded connections that can create intermittent faults.

• Always disconnect the appliance from power (unplug or switch off circuit breaker) before servicing.
• Match each connector to its mating plug and follow the OEM wiring diagram for routing and color codes.
• Secure the harness away from heat sources and moving parts; use existing clips and fasteners.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Replacement bumper that cushions appliance parts and absorbs shock to prevent rubbing, rattling and surface damage. Restores proper fit and quieter operation for components that contact cabinets, doors or panels. What it does:

• Cushions contact points to reduce noise from doors, drawers or panels.
• Prevents metal-to-metal or metal-to-surface scraping that can cause wear or cosmetic damage.
• Helps components close and seat more evenly to reduce vibration and movement.
• Common symptom fixes: eliminates rattling, stops rubbing noises, and prevents chipping or scuffing where parts meet.

• One bumper.

• High-level, tool-light replacement; usually presses into or adheres to the mounting surface.
• Disconnect power or unplug the appliance before opening panels where required.
• Inspect surrounding clips/retainers and clean the mounting area for best adhesion or fit.

This genuine replacement power cord restores electrical connection to your appliance so it can safely receive power. It replaces a damaged or worn cord to help eliminate power loss and reduce electrical hazards. What it does:

• Provides the electrical connection between the appliance and your home's power supply
• Replaces frayed, cracked, or burned cord insulation and damaged plugs
• Helps stop intermittent power issues caused by a faulty cord or connector
• Restores safe, reliable power routing when the original cord is compromised

• Always disconnect power at the breaker or unplug the appliance before installing
• Follow the appliance wiring diagram and route the cord to avoid heat or pinch points
• Secure strain relief and connectors per the manufacturer's instructions

Size: 10-24 x 3/8 inch.

Push-in nut that secures panels, trim, or small components to studs or shafts. Restores a firm, vibration-resistant fastener to help stop loose panels and rattling caused by a worn or missing nut. What it does:

• Secures panels, trim or small assemblies to mounting studs or shafts.
• Helps keep parts aligned and reduces vibration or rattling during operation.
• Common symptom: loose or shifting panels, audible rattling, or components that won't stay in place.
• Designed for a push-fit installation to replace worn or missing fasteners.

• Always disconnect power to the appliance before servicing.
• Push the nut fully onto a clean, undamaged stud until seated; replace damaged studs or mounting hardware.
• If needed, use pliers or a socket to press the nut on evenly—avoid deforming surrounding plastic or sheet metal.

This retainer is a small mounting clip that secures internal components in place to prevent shifting and noise during operation. It restores proper alignment so panels or assemblies stay fastened and stable. What it does

• Holds a panel, trim, or internal component securely in its mounting location
• Prevents rattling, vibration noise, and loose or sagging parts
• Keeps connected parts aligned for reliable operation
• Commonly replaced when clip is cracked, broken, or missing

• One retainer clip

• Disconnect power before starting any repair
• Remove necessary panels or access covers to reach the damaged clip
• Replace the clip in the same orientation; avoid forcing parts to prevent damage
• If additional fasteners are damaged or missing, replace them as needed for a secure installation