Msd2435gr Parts

This door closer with cup mounts on the hinge to control the door's final closing motion. It restores smooth, consistent closing and helps the gasket seal evenly to maintain proper temperatures.

• Provides hinge cam action that pulls the door closed during the last few inches
• Helps keep the door aligned so the gasket seals evenly around the cabinet
• Reduces slamming and prevents the door from drifting or popping back open
• Common symptoms of wear: clicking/grinding at the hinge, sagging or rubbing, poor self-closing, or moisture/frost near the door

• Unplug the refrigerator and remove items from the door to reduce weight
• Support the door; remove hinge cover and fasteners, then lift the door off to access the closer components
• Match the original orientation; install the new closer and cup on the hinge/door seats
• Reinstall and align the door; tighten hinge screws and verify smooth self-closing and gasket contact

This evaporator fan motor drives the internal fan that circulates cold air across the evaporator coils and throughout the fresh food and freezer compartments, helping maintain even temperatures and proper cooling.

• Moves air over the evaporator to remove heat and reduce frost buildup
• Helps restore weak cooling, warm spots, or long run times
• Can resolve frost or ice accumulation on the evaporator cover due to poor airflow

• Disconnect power before servicing; wear cut-resistant gloves
• Access is typically from the freezer section behind the rear panel
• Transfer fan blade and any mounting components from the old motor if required
• Verify correct motor orientation and wire placement per your model's diagram

This seal strip replaces a worn or damaged door gasket edge to restore a proper seal and help the appliance maintain temperature and operate quietly. It's a direct-fit service part used where a continuous seal is required. What it does:

• Provides a flexible barrier along the door/frame to reduce air leaks and heat/cold loss
• Helps prevent moisture buildup and improves energy efficiency when sealing is restored
• Reduces rattling and vibration caused by a compressed or torn seal edge
• Commonly replaced when the strip is torn, missing, or no longer adheres properly

• One seal strip

• Disconnect power to the appliance before servicing to avoid electrical or burn hazards
• Clean and dry the mounting surface; remove old adhesive or residue for best adhesion
• Align the strip carefully and press firmly; allow any adhesive to cure per manufacturer instructions

This fountain switch controls the refrigerator dispenser's user-activated circuit so the dispenser responds when the lever or pad is pressed. Replaces a worn or failed dispenser switch to restore normal dispenser control. What it does:

• Acts as the user-activated switch for the water/ice dispenser circuit
• Allows the dispenser to energize the valve or auger motor when pressed
• Commonly replaced when dispenser fails to respond or is intermittent
• Helps stop unexpected dispenser activation due to a stuck switch

• One fountain switch

• Disconnect power to the appliance before beginning any repair
• Access may require removing the dispenser/control panel; handle plastic trim carefully
• Avoid pulling on wires; disconnect connectors by their housings, not the wires

This cover assembly for the air return guides airflow and protects the return opening from debris so the appliance runs more reliably. It restores correct air pathing and helps maintain normal drying/cooling performance. What it does:

• Directs and protects the air return opening to maintain proper airflow
• Helps prevent lint, dust, and debris from entering sensitive internal components
• Can reduce abnormal noise caused by loose or missing return covers
• Restores designed airflow behavior that supports efficient operation

• Disconnect power to the appliance before starting any work
• Remove exterior panels as needed to access the air return and retain fasteners for reassembly
• Inspect surrounding seals and ducts; replace damaged parts to ensure proper airflow

This is a replacement hex nut used to secure appliance components and fasteners. It restores a tight, reliable connection where a worn or missing nut causes loose panels, trim, or bracketing. What it does:

• Secures threaded studs, bolts, or fasteners to keep panels and components in place
• Restores proper fastening when original nut is stripped, corroded, or lost
• Helps eliminate rattling, vibration, or loose parts caused by a missing/failed nut
• Compatible with the appliance locations that use a standard hex nut for mounting

• Turn off and unplug the appliance before accessing interior panels or fasteners
• Use the correct wrench or socket size to avoid rounding the nut
• Replace only like-for-like nuts; if thread damage is present, inspect and replace the mating bolt/stud as needed

This ball sleeve guides and supports the valve ball inside the water/dispensing assembly to help maintain a proper seal and smooth movement. Replacing a worn sleeve restores reliable valve operation and reduces intermittent leaks or flow issues. What it does:

• Positions and protects the valve ball for consistent seating and sealing
• Prevents wear between the ball and valve bore to maintain proper flow control
• Helps stop dripping, leaking, or inconsistent dispensing caused by a damaged sleeve
• Works as the mating surface for the ball to ensure smooth operation

• One ball sleeve

• Disconnect power and water supply before starting any repair
• Replace only with the correct part number to ensure proper fit and seal
• Inspect surrounding valve components and seals; replace if worn or damaged
• Test for leaks and proper operation after reassembly

A small replacement screw used to secure appliance panels and components so assemblies stay aligned and stable during normal use. Simple, direct fix for loose trim, panels, or mounting points. What it does:

• Secures panels, brackets, or small components to prevent rattling and movement
• Restores proper alignment where a missing or damaged fastener causes gaps
• Helps stop vibration-related noise from loose parts
• Functions as the original-style fastener matching OEM fit and purpose

• Disconnect power and water to the appliance before servicing where applicable
• Use the correct screwdriver or bit to avoid stripping the head
• Thread the screw in by hand to start, then tighten snugly—do not over-torque
• Keep removed hardware organized and compare sizes before installing

A replacement door gasket that restores a tight seal around the oven door to help maintain proper cooking temperature and improve efficiency. Fits Whirlpool ovens and ranges that use part A3189394. What it does

• Seals the oven cavity to reduce heat loss and help maintain consistent cooking temperatures.
• Helps prevent heat from escaping around the door, improving energy use and cook results.
• Worn, torn, or flattened gaskets can cause uneven baking or longer cook times.
• Replacing a damaged gasket can reduce hot spots on the exterior and nearby cabinetry.

• Disconnect power and ensure the oven is completely cool before starting.
• Remove the old gasket by pulling it out of the door channel; clean the channel before installing the new gasket.
• Press the new gasket into the channel around the full perimeter, working from one corner and ensuring an even fit.

This replacement bracket secures the refrigerator ice maker assembly so it stays properly positioned for reliable ice production. It restores stable mounting and helps prevent the ice maker from shifting or coming loose. What it does:

• Holds the ice maker assembly in place on the freezer liner or mounting frame
• Keeps the ice maker aligned for proper operation and water fill
• Helps stop vibration or movement that can cause noisy operation or misfeeds
• Useful when the original bracket is bent, broken, or missing

• Disconnect power to the refrigerator and shut off the water supply before starting
• Remove the ice maker to access the bracket mounting screws
• Reuse existing screws if undamaged; tighten to secure but avoid overtightening
• If mounting points or surrounding plastic are damaged, replace or repair before reinstalling

Size: 8-32 x 1/4 inch.