Msd27566pw Parts

This terminal cover protects the appliance's power connection area, keeping wiring and terminals enclosed to reduce shock and short risks. It's a direct-replacement trim piece that restores the factory protective barrier around the terminal block. What it does:

• Covers and shields the terminal block where the power cord connects, helping prevent accidental contact.
• Helps reduce the risk of shorting or arcing at exposed power connections.
• Addresses symptoms like visible exposed terminals, loose or unprotected wiring at the power entry area, or a missing/broken cover.
• Restores the appliance's intended safety enclosure after repair or shipping damage.

• One terminal cover

• Always disconnect all power (unplug or shut off breaker) before accessing the terminal block.
• Remove the old cover and position the replacement over the terminal area so mounting holes align; secure with the original screw(s).
• Inspect terminal screws and wiring for tightness and damage while cover is off; do not attempt electrical repairs.
• If terminals or wiring are damaged, replace or repair those components before reinstalling the cover.

This egg tray replaces the cracked or missing refrigerator door egg holder so eggs stay organized and reduce breakage. Molded tray keeps eggs in place and restores full use of the door storage area. What it does:

• Holds and secures eggs in the refrigerator door to prevent rolling and cracking
• Replaces broken, cracked or missing egg storage trays
• Restores proper fit and function of the door shelf area where eggs are stored
• Helps keep eggs organized for easier access

• One egg tray

• Designed to snap into the designated door shelf location; no special tools typically required
• Align tray tabs with the door shelf slots and press until it clicks into place
• Clean with mild detergent before installation; avoid abrasive cleaners
• Handle carefully to avoid cracking during installation

A single replacement screw used to fasten appliance panels and components, restoring secure fit and reducing vibration or noise. Simple, low-cost part for repairs that need a missing or stripped fastener. What it does:

• Secures panels, trim, or small component housings to the appliance frame
• Helps stop rattling, vibration, and misalignment caused by loose or missing screws
• Keeps internal components properly seated to maintain normal operation
• Used wherever the OEM specifies this exact fastener

• One replacement screw

• Disconnect power before servicing the appliance to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread by hand first, then tighten snugly—do not overtighten
• Keep small parts away from children and pets

This 8-32 x .340 machine screw secures small appliance panels and components for a reliable fit. It's a simple replacement fastener when original screws are missing, stripped, or worn. What it does:

• Fastens panels, brackets, and internal components where 8-32 threads are required
• Provides a short, firm hold for thin materials and assemblies
• Useful when original mounting screws are lost or damaged
• Matches OEM thread size and length for correct fit in designed screw bosses

• One 8-32 x .340 machine screw

• Use the correct screwdriver or nut driver to avoid stripping the head
• Do not overtighten; snug to secure without deforming plastic or stripping threads
• Confirm screw length and thread size match the original before installation
• Disconnect power and follow appliance safety precautions when accessing internal parts

This genuine replacement screw secures appliance panels and trim so covers, consoles, and components stay firmly in place for safe, quiet operation. It replaces worn or missing fasteners to restore proper fit and reduce vibration and rattling. What it does:

• Secures control panels, trim pieces, or access panels to the appliance frame
• Keeps panels aligned to prevent gaps and light leaks
• Reduces vibration-related noise from loose panels or components
• Helps maintain safe operation by keeping covers and guards properly attached

• The replacement screw shown/listed

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start the screw by hand to ensure proper thread engagement, then tighten securely but do not overtighten

This is a replacement mounting screw for securing appliance components and panels. It restores proper fastening where a missing or stripped screw causes loose parts or rattling. What it does:

• Fastens panels, brackets, or small components to restore secure attachment
• Prevents vibration and rattling caused by loose or missing fasteners
• Replaces stripped or lost factory screws to maintain original fit
• Matches OEM fit for the specific mounting location when the part number is specified

• Use the matching screw location and size specified by the parts diagram
• Hand-start threads to avoid cross-threading; tighten securely but do not overtighten
• Disconnect power to the appliance before removing panels or components
• If threads are damaged, replace with correct OEM screw—do not force a mismatched fastener

Size: 8-32 x .312 inch.

This thermal overload protector helps prevent motor overheating by interrupting power when temperatures exceed safe limits. It restores normal operation once the motor cools, protecting the appliance from damage and reducing risk of failure. What it does:

• Senses excessive motor temperature and interrupts current to stop the motor from running when overheated
• Helps prevent motor burnout and related electrical damage
• Can resolve symptoms such as a dryer or washer motor that stops mid-cycle, won't start, or trips the circuit during heavy use
• Works as a safety device in the motor circuit rather than a control or relay

• One thermal overload protector

• Disconnect power before accessing or replacing the motor overload; follow appliance-specific service manual steps
• Handle terminals and wiring carefully; replace using the same connections and orientation as the original
• If the motor repeatedly overheats after replacement, inspect motor bearings, venting, or other causes rather than replacing overload repeatedly

This door closer with cup mounts on the hinge to control the door's final closing motion. It restores smooth, consistent closing and helps the gasket seal evenly to maintain proper temperatures.

• Provides hinge cam action that pulls the door closed during the last few inches
• Helps keep the door aligned so the gasket seals evenly around the cabinet
• Reduces slamming and prevents the door from drifting or popping back open
• Common symptoms of wear: clicking/grinding at the hinge, sagging or rubbing, poor self-closing, or moisture/frost near the door

• Unplug the refrigerator and remove items from the door to reduce weight
• Support the door; remove hinge cover and fasteners, then lift the door off to access the closer components
• Match the original orientation; install the new closer and cup on the hinge/door seats
• Reinstall and align the door; tighten hinge screws and verify smooth self-closing and gasket contact

This evaporator fan motor drives the internal fan that circulates cold air across the evaporator coils and throughout the fresh food and freezer compartments, helping maintain even temperatures and proper cooling.

• Moves air over the evaporator to remove heat and reduce frost buildup
• Helps restore weak cooling, warm spots, or long run times
• Can resolve frost or ice accumulation on the evaporator cover due to poor airflow

• Disconnect power before servicing; wear cut-resistant gloves
• Access is typically from the freezer section behind the rear panel
• Transfer fan blade and any mounting components from the old motor if required
• Verify correct motor orientation and wire placement per your model's diagram

This seal strip replaces a worn or damaged door gasket edge to restore a proper seal and help the appliance maintain temperature and operate quietly. It's a direct-fit service part used where a continuous seal is required. What it does:

• Provides a flexible barrier along the door/frame to reduce air leaks and heat/cold loss
• Helps prevent moisture buildup and improves energy efficiency when sealing is restored
• Reduces rattling and vibration caused by a compressed or torn seal edge
• Commonly replaced when the strip is torn, missing, or no longer adheres properly

• One seal strip

• Disconnect power to the appliance before servicing to avoid electrical or burn hazards
• Clean and dry the mounting surface; remove old adhesive or residue for best adhesion
• Align the strip carefully and press firmly; allow any adhesive to cure per manufacturer instructions

This fountain switch controls the refrigerator dispenser's user-activated circuit so the dispenser responds when the lever or pad is pressed. Replaces a worn or failed dispenser switch to restore normal dispenser control. What it does:

• Acts as the user-activated switch for the water/ice dispenser circuit
• Allows the dispenser to energize the valve or auger motor when pressed
• Commonly replaced when dispenser fails to respond or is intermittent
• Helps stop unexpected dispenser activation due to a stuck switch

• One fountain switch

• Disconnect power to the appliance before beginning any repair
• Access may require removing the dispenser/control panel; handle plastic trim carefully
• Avoid pulling on wires; disconnect connectors by their housings, not the wires

This cover assembly for the air return guides airflow and protects the return opening from debris so the appliance runs more reliably. It restores correct air pathing and helps maintain normal drying/cooling performance. What it does:

• Directs and protects the air return opening to maintain proper airflow
• Helps prevent lint, dust, and debris from entering sensitive internal components
• Can reduce abnormal noise caused by loose or missing return covers
• Restores designed airflow behavior that supports efficient operation

• Disconnect power to the appliance before starting any work
• Remove exterior panels as needed to access the air return and retain fasteners for reassembly
• Inspect surrounding seals and ducts; replace damaged parts to ensure proper airflow

This knurled pin secures the juicer cone and helps transmit torque for proper juicing action. It replaces a worn or damaged roll pin to restore stable cone alignment and smooth operation. What it does:

• Secures the juicer cone or attachment to the drive shaft to prevent slipping
• Transfers rotational force from the motor to the juicer cone
• Helps stop wobble, misalignment, or intermittent engagement of the juicer cone
• Commonly replaced when the pin is bent, worn, or broken

• One knurled pin

• Turn off and unplug the appliance before servicing to avoid shock or injury
• Remove the juicer cone and any retaining parts per the service diagram before replacing the pin
• Use appropriate hand tools; avoid excessive force which can damage the shaft or housing

This is a replacement hex nut used to secure appliance components and fasteners. It restores a tight, reliable connection where a worn or missing nut causes loose panels, trim, or bracketing. What it does:

• Secures threaded studs, bolts, or fasteners to keep panels and components in place
• Restores proper fastening when original nut is stripped, corroded, or lost
• Helps eliminate rattling, vibration, or loose parts caused by a missing/failed nut
• Compatible with the appliance locations that use a standard hex nut for mounting

• Turn off and unplug the appliance before accessing interior panels or fasteners
• Use the correct wrench or socket size to avoid rounding the nut
• Replace only like-for-like nuts; if thread damage is present, inspect and replace the mating bolt/stud as needed