Mtw5800tw Maytag Washer Parts

This anti-rattle screw secures panels or brackets to prevent vibration noise in compatible appliances. Replacing a missing or stripped screw restores a tight fit and helps keep the cabinet and assemblies stable and quiet.

• Secures brackets, ducts, or panels to reduce buzzing and rattling during operation
• Replaces a lost, worn, or damaged anti-rattle fastener
• Helps maintain proper alignment and prevents vibration-related wear
• Typical symptoms include persistent rattling, a loose panel, or hardware found inside the cabinet

• Disconnect power before servicing; for gas appliances, shut off the gas supply
• Access the mounting point and remove the loose or damaged screw
• Start the new screw by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the bracket/clip before reassembly

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

This agitator drive shaft sits inside the washer's gearcase and transfers motion to the agitator. Replacing a worn or stripped shaft restores firm engagement and reliable wash action while helping reduce slip and grinding during agitation.

• Transfers oscillating motion from the transmission to the agitator
• Provides the splined interface that engages the agitator/coupler
• Common symptoms include no agitation, intermittent/slipping agitation, or grinding/clicking from the gearcase
• Visible wear, rounded splines, or a bent shaft can lead to a loose or non-moving agitator

• Disconnect power and water; use proper PPE
• Requires removing the cabinet and gearcase; drain and reseal the gearcase per service procedures
• Keep gears, spacers, and clips in order; reassemble in the original orientation
• Inspect mating parts (agitator coupler/splines, drive block, seals) and replace if worn

Used for lid switch.

This lid hinge pad fits between the washer lid hinge and the cabinet. It cushions the joint to reduce squeaks and metal wear, helping keep the lid aligned and operating smoothly.

• Provides a protective wear surface between the hinge and cabinet/lid
• Reduces squeaks, creaks, and rattling when opening or closing the lid
• Helps maintain proper lid alignment and smooth movement
• Common signs it's worn or missing: squeaking lid, rubbing/scuff marks at the hinge, loose or wobbly lid

• Disconnect power to the washer before servicing
• Support the lid to relieve hinge tension and access the hinge area per your model
• Remove the worn pad and press the new pad fully into the hinge location
• Test lid operation; inspect the opposite hinge and replace its pad as needed if your model uses two

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.

• Supports and centers the spin basket on the tub centerpost/drive shaft
• Provides a low-friction bearing surface to reduce wear and noise
• Helps maintain basket alignment and stability during spin
• When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin

• Disconnect power and water supply before servicing; use proper PPE
• Access typically requires removing the agitator, inner basket, and related drive components
• Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
• Seat the bearing fully and verify smooth basket rotation before reassembly

This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.

• Applies tension to prevent rattling and buzzing during use
• Helps keep the mounted piece properly seated and aligned
• Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
• Simple, drop-in replacement where the original clip is used

• Disconnect power to the appliance before servicing
• Note the original clip's orientation; transfer the new clip the same way
• Use needle-nose pliers for placement; avoid over-bending the clip
• The component is secure and clears adjacent parts before reassembly

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

Timer knob assembly restores manual control of the appliance timer so you can select and change cycle times with a secure, easy-to-grip knob. Replaces a cracked, worn, stripped, or missing timer knob to restore normal operation. What it does:

• Mounts to the timer/control shaft to allow manual selection of timed cycles.
• Re-establishes engagement when the original knob is stripped, loose, cracked, or missing.
• Provides a firm grip and tactile feedback for accurate setting of cycle times.

• Disconnect power to the appliance before servicing to reduce risk of shock.
• Pull the old knob straight off the control shaft; align splines and push the replacement knob fully onto the shaft until seated.
• If the knob uses a set screw, tighten gently—do not over-torque.
• If the control shaft is damaged or the knob will not engage properly, replace the control.

This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:

• Holds three wiring terminals in the correct orientation for a mating connector
• Insulates and locks terminals to reduce arcing and overheating at the plug
• Replaces cracked, brittle, or heat-damaged connector housings
• Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched

• 1 three-circuit connector housing

• Disconnect power before servicing the appliance
• Note wire/terminal positions and transfer them one at a time into the new housing
• Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
• Fully seat each terminal until it locks and the connector latch engages securely

Size: 10-16 x 5/8 inch.

Includes drive tube spacer, "T" bearing and both shaft seals.

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

This brake release cam works with the washer's brake assembly to disengage the brake during spin and re-engage it at stop. Replacing a worn cam restores smooth basket spin and reduces squeal or grinding at spin transitions.

• Disengages the brake so the basket can spin; helps reapply the brake as the cycle ends
• Supports smooth starts and stops of the spin cycle
• Worn or damaged cams can cause no spin or intermittent spin
• Common symptoms include loud squeal/grinding at start/stop or a burning odor near the brake area

• Disconnect power (and water supply, if moving the washer) before service
• Access the brake/basket drive area; the brake spring is under tension—use caution and eye protection
• Note orientation of parts before removal; seat the new cam correctly
• After reassembly, run an empty spin test to verify operation