Mvw8700vq0 Parts

This lid hinge pad fits between the washer lid hinge and the cabinet. It cushions the joint to reduce squeaks and metal wear, helping keep the lid aligned and operating smoothly.

• Provides a protective wear surface between the hinge and cabinet/lid
• Reduces squeaks, creaks, and rattling when opening or closing the lid
• Helps maintain proper lid alignment and smooth movement
• Common signs it's worn or missing: squeaking lid, rubbing/scuff marks at the hinge, loose or wobbly lid

• Disconnect power to the washer before servicing
• Support the lid to relieve hinge tension and access the hinge area per your model
• Remove the worn pad and press the new pad fully into the hinge location
• Test lid operation; inspect the opposite hinge and replace its pad as needed if your model uses two

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This is a range hood grease filter. It traps airborne grease and cooking residue so the blower and ductwork stay cleaner and the hood maintains proper airflow.

• Captures grease and particulates from cooking vapors to protect the fan and motor
• A clogged or damaged filter can cause reduced suction, noisy operation, or lingering cooking odors
• Replace if the mesh is clogged, warped, punctured, or if cleaning no longer restores airflow
• Helps maintain ventilation performance and reduce buildup inside the hood

• Disconnect power to the hood before servicing
• Allow the hood and filters to cool before handling
• Open the filter latch or tabs, remove the old filter, and seat the new filter with the tabs/latch aligned
• Restore power; check for proper airflow

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

This detergent dispenser assembly stores detergent and releases it at the right point in the wash cycle. Replace it to restore reliable soap dispensing and consistent cleaning when the cup door or mechanism fails.

• Holds detergent securely until the cycle calls for release
• Opens the detergent cup at the proper time for effective washing
• Helps prevent premature detergent loss and residue on dishes/clothes
• Common symptoms: soap door won't latch/open, detergent left in cup after cycle, visible cracks or leaks around the dispenser area

• Disconnect power and shut off water before service
• Access the dispenser at its mounting location; remove fasteners/release tabs and unplug the harness
• Seat the new assembly evenly on a clean surface to ensure a good seal; reconnect wiring
• Reassemble and run a test cycle to check for leaks

This is the factory replacement microwave door assembly. It restores a smooth, secure door closure and proper operation so the unit can open and close reliably and look like new. What it does:

• Provides a complete, aligned door to open/close the cavity smoothly
• Ensures latch hooks engage properly so the appliance can operate
• Replaces doors that are cracked, warped, or have broken handle mounts
• Addresses issues like the unit not starting unless the door is pressed, or stopping when the door is moved
• Helps resolve sparking/arcing around the door opening caused by a damaged door choke or screen

• One door assembly

• Disconnect power at the breaker before servicing; microwaves contain high-voltage components
• For over-the-range units, support or remove the microwave from the wall to safely access and handle the door
• Transfer any reusable hardware/hinge pins/trim from the original door as needed
• Align the hinges and verify the door closes, latches, and opens smoothly before remounting

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

This pushbutton installs in the control console and actuates the underlying switch, restoring positive, reliable selection of a cycle or feature and a clean, finished appearance when the original button is worn, sticky, or broken. What it does

• Provides the user-facing cap that presses the internal control switch
• Restores smooth button travel and positive engagement
• Helps ensure selections register consistently
• Common symptoms: button cap cracked/missing, sticks or won't spring back, selection only registers when pressed hard, loose or wobbly button

• 1 pushbutton

• Disconnect power before servicing to avoid electrical shock
• Access the control/console per your service manual
• Note orientation; release retaining tabs and remove old button
• Seat the new button fully; test travel and function before reassembly

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: 5  Position Switch
 

The washer pulley Cover is an OEM replacement part for Whirlpool washing machines. It is a removable plastic shroud that houses the drive pulley and belt mechanism.

Causes of a bad pulley cover can include cracks or breaks from repeated opening and closing over time. Chemical or moisture exposure can also damage plastic through standard usage cycles. 

Symptoms of a failing pulley cover include:

• Inability to properly close or latch the cover  
• Leaks or debris entering the pulley compartment
• Interference with belt or pulley movement
• Loose fasteners or mounting points that cause misalignment

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, and Kenmore models.

This recirculation pump assembly drives water through the appliance's circulation system, maintaining steady flow and pressure for proper operation. Replace it if water won't circulate, performance drops, or the unit becomes noisy or shows a pump-related error.

• Moves water through internal channels to maintain consistent circulation and pressure
• Helps ensure effective cleaning/operation during wash or circulation steps
• Common failure symptoms: no/weak water movement, poor results, humming or grinding noises
• Trigger pump/circulation error messages or cause cycles to stall

• Disconnect power and shut off water supply before servicing
• Access is typically from the bottom/front; remove toe-kick or lower panels as needed
• Expect residual water; protect the area and transfer clamps/fittings from the old pump if required
• Seat any seals properly, reconnect hoses/wiring securely, and test for leaks and proper circulation

This adjustable leveling leg helps stabilize and properly level your appliance on uneven floors. Replacing a worn or missing leg reduces wobble and vibration so doors align and the unit operates smoothly.

• Screws into the base to raise or lower a corner for precise leveling
• Helps prevent rocking, vibration, and rattling during use
• Promotes even weight distribution to protect the cabinet and flooring
• Restores proper door/drawer alignment once the unit is level

• Disconnect power; shut off water supply before servicing
• Carefully pull or tip the appliance to access the leg; use a helper for safety
• Start threads by hand, then adjust height with a wrench—do not over-extend
• Verify level front-to-back and side-to-side; recheck after moving or loading

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.