Mwf W9700vu00 Parts

This 2-pack of dryer vent clamps secures the vent hose to the dryer outlet and the wall/vent hood. A tight connection helps maintain airflow, reduce lint leaks, and keep the duct from slipping off during use.

• Tightens around the vent hose to hold it securely to the dryer exhaust collar or exterior vent
• Helps prevent hose detachment, air leaks, and lint escaping at the connection
• Supports proper exhaust airflow by keeping connections sealed and stable
• Common symptoms pointing to replacement: hose won't stay on, visible gaps or lint around fittings, rattling at the vent, or longer dry times from poor ventilation

• Disconnect power; for gas dryers, shut off gas supply before moving the appliance
• Slide a clamp over the hose, seat the hose fully on the collar, position clamp over the fitting, and tighten with a screwdriver or nut driver
• Do not overtighten; avoid crushing thin foil ducting; ensure the hose is straight and not kinked
• Restore power and verify strong airflow at the exterior exhaust

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

The dispenser actuator cam links the actuator to the dispenser mechanism, converting movement into a precise release. Replacing a worn or broken cam restores smooth, reliable dispensing and helps prevent incomplete or erratic operation. What it does:

• Transfers actuator motion to engage or release the dispenser mechanism
• Maintains correct alignment and travel for consistent operation
• A worn or broken cam can cause the dispenser not to open/close, feel loose or sticky, or make unusual clicking noises
• Common corrective part when the actuator moves but the dispenser doesn't function properly

• 1 dispenser actuator cam

• Disconnect power; turn off water supply if applicable before servicing
• Access the dispenser assembly per your model; note linkage/spring orientation (take photos) before removal
• Align the new cam carefully—do not force; verify smooth actuator travel by hand
• Reassemble and test operation before finalizing

This factory fastener secures appliance components such as panels, brackets, and covers. Replacing a missing, stripped, or rusted screw restores a tight fit and helps reduce vibration, rattling, and shifting during operation.

• Fastens metal or plastic parts to the appliance cabinet/frame
• Helps maintain proper alignment and reduces noise from loose panels
• Replaces hardware that is missing, corroded, or with stripped threads
• Symptoms include rattling, looseness, gaps, or misaligned parts

• Disconnect power; shut off gas/water before servicing
• Support panels to prevent drops; watch for sharp edges
• Start threads by hand to avoid cross-threading; use the correct driver
• Do not overtighten; match the original screw's location and orientation

This bracket secures a component or panel inside your appliance, keeping it properly aligned and stable during operation. Replacing a bent, cracked, or missing bracket restores solid mounting and helps prevent vibration and further damage.

• Provides a rigid mounting point for a specific component or panel
• Maintains proper alignment for reliable fit and function
• Replaces damaged, deformed, or missing bracket hardware
• Typical symptoms include loose or rattling parts, misaligned panels, vibration, or components shifting out of place

• Disconnect power (and shut off water or gas, if applicable) before servicing
• Note the original bracket's orientation; transfer any reusable hardware to the new bracket
• Use existing or manufacturer-specified screws; tighten securely without over-torquing
• Verify component alignment and clearances before restoring power/service

This replacement hose restores a secure, leak-resistant path for water inside your appliance. Replacing it helps stop leaks and keeps cycles running as intended.

• Carries water between internal components during operation
• Maintains a sealed path to help prevent leaks
• Helps ensure proper filling, circulation, or draining as designed
• Common symptoms include water leaking under/inside the unit, standing water, or slow/incomplete fill or drain

• Disconnect power and shut off the water supply before servicing
• Keep towels or a shallow pan ready to catch residual water
• Note hose routing and clamp positions; transfer existing clamps if they're reusable
• After installation, run a test cycle and check carefully for leaks

This replacement screw secures appliance components and panels so they stay aligned and rattle-free during operation. Replace stripped, missing, or corroded hardware to restore a tight fit and dependable performance. What it does

• Fastens brackets, panels, and internal sub-assemblies in the appliance
• Helps maintain alignment to reduce vibration and rattling
• Replaces missing, rusted, or stripped screws that no longer hold
• Useful when a part won't mount securely or a screw backs out during use

• One screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Compare to the original for length and thread style for the location
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; if the mounting hole or clip is worn, replace it

This Dispenser Divider installs in the washer's detergent drawer to separate and control liquid or powder detergent in the main-wash compartment. Replacing a worn or missing divider helps restore proper dispensing and more consistent cleaning results.

• Sits in the main-wash section to select liquid or powder detergent
• Directs and regulates water flow for complete detergent siphoning at the right time
• Replaces a cracked, warped, or missing divider that can affect wash performance

• Disconnect power and turn off water supply before servicing
• Pull the dispenser drawer out and depress the release tab to remove it
• Lift out the old divider, clean the compartment, and snap the new divider in the correct orientation (liquid or powder as marked)
• Reinstall the drawer and run a short cycle to verify proper dispensing

Water distribution lever

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

Restore the clean look and proper function of your washer's detergent compartment with this detergent dispenser drawer cover. It replaces a cracked or missing cover so the drawer closes correctly and helps reduce splashing at the dispenser. What it does:

• Covers and protects the front of the detergent dispenser drawer
• Helps the drawer align and close properly for consistent dispensing
• Replaces broken or missing cover tabs that prevent the drawer from staying in place
• Common symptoms: cracked/missing cover, broken tabs, drawer won't close or feels loose, splashing/leaks at the dispenser area

• 1 detergent dispenser drawer cover

• Unplug the appliance and shut off water supply before servicing
• Pull the dispenser drawer out and depress the release tab to remove it
• Release the locking tabs to remove the old cover; snap the new cover fully into place
• Reinstall the drawer and run a quick test to check operation

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This front counterweight mounts to the washer's outer tub to help balance and stabilize the drum during spin. Replacing a damaged weight can reduce vibration and noise and help prevent the machine from walking. What it does:

• Adds mass at the front of the tub to counterbalance loads during spin
• Helps control vibration, shaking, and banging noises
• Can resolve out-of-balance interruptions or excessive movement
• Visible cracks or broken mounting ears indicate the weight needs replacement

• One front counterweight

• Disconnect power and water; use proper lifting techniques—this part is heavy
• Support the tub and remove front cabinet components/door boot as needed for access
• Remove and retain mounting bolts; tighten bolts evenly when reinstalling
• Inspect mounting points and suspension components while accessible; replace if worn

This replacement ball is the small spherical component used in select Whirlpool-built mechanisms. It acts as a moving seal or detent to control flow or position, restoring smooth, reliable operation when the original ball is worn or missing. What it does:

• Provides the sealing or detent action within its valve, hinge, or track assembly
• Helps prevent backflow, leaks, or unwanted movement
• Restores smooth operation when mechanisms feel rough, bind, or won't stay in position
• Replace if the original is deformed, pitted, corroded, or missing

• 1 ball

• Disconnect power and shut off water supply if applicable
• Access the specific assembly per your model's service documentation and note part order
• Place the ball in its seat/track with any companion spring or seal as designed
• Inspect mating surfaces and related seals or springs and replace if worn

This dishwasher door latch lever links the handle to the latch and safety switches so the door can secure closed and the cycle can start. Replacing a cracked or worn lever restores reliable latching and starts. What it does:

• Transfers handle movement to the latch mechanism and door switches
• Helps the control recognize a fully closed door so the dishwasher will run
• Contributes to keeping the door securely closed during operation
• Resolves: cycle won't start, door won't latch or stay closed, need to hold door to run, loose/floppy handle feel

• 1 lever

• Disconnect power at the breaker before servicing the door
• Open the door and remove inner door panel screws to access the latch/handle area
• Note the original lever's orientation; move any springs/clips to the new lever and seat it fully in the pivot
• Reassemble, verify smooth handle action, and ensure the door latches and a cycle initiates

This water level pressure switch senses air pressure from the tub and signals the control when the correct level is reached. Replacing a failed switch restores proper filling and helps the washer advance through each cycle reliably.

• Monitors tub water level via the pressure (air) hose and sends the signal to stop filling
• Helps prevent overfilling or underfilling so cycles can start and complete properly
• Common symptoms of a failed switch: keeps filling or won't fill, stuck on sensing, won't advance to wash or spin, or drains immediately after filling
• Also called a water level sensor or pressure sensor in some documentation

• Disconnect power and turn off water supply before servicing
• Access the switch near the control/console area; note hose routing and connector position
• Transfer the pressure hose and electrical connector to the new switch; inspect the hose for kinks, cracks, or blockages and ensure an airtight fit
• Restore power and run a quick fill/test cycle to verify normal operation