Mws939 Parts

This tub-to-pump hose connects the washer's outer tub to the drain pump, channeling water out during the drain cycle. Replacing a worn hose helps stop leaks and restore consistent draining when the original is cracked or deteriorated.

• Provides a sealed path from the outer tub to the drain pump during draining
• Helps the washer remove water at the end of wash and rinse cycles
• Common failure symptoms: water leaking at the front/bottom, puddles after a cycle, or slow/no drain
• Visual clues: cracks, splits, swelling, or soft spots in the hose rubber

• Unplug the washer and turn off water supply; expect residual water—use a pan/towels
• Access the hose per your model (often behind the lower front/service panel); note routing/orientation before removal
• Transfer and reuse the existing clamps; seat the hose fully on both fittings and secure evenly
• After reassembly, run a brief fill/drain test while watching for leaks

This trunnion plate secures the washer's inner basket to the drive hub/trunnion, keeping the tub centered and stable during spin. Replace it if the basket feels loose, wobbles, or makes scraping/knocking noises from the hub area. What it does:

• Couples the inner basket to the trunnion/drive hub so the basket spins true
• Helps maintain alignment to reduce vibration and tub-to-basket contact
• Wear can allow play or slippage at the hub connection
• Common symptoms: wobble, scraping/grinding, excessive vibration, poor spin results

• One trunnion plate

• Disconnect power and wear cut-resistant gloves before servicing
• Access typically requires removing the agitator/wash plate and lifting out the inner basket
• Clean and inspect mating surfaces; align the plate correctly and tighten fasteners evenly
• Check related parts for wear and replace if needed

This tub cover seal fits between the outer tub and the tub cover/splash guard on compatible washers. It keeps wash water and suds contained, helping prevent leaks from the top of the cabinet during agitation and spin.

• Forms a watertight barrier between the outer tub and the tub cover/splash guard
• Helps prevent splash-over and top-rim leaks during wash and spin
• Maintains proper containment of water and suds inside the tub assembly
• Common failure signs: water leaking from the top area, wet streaks down the outer tub, visible cracks, hardening, or flattening of the seal

• Disconnect power and shut off water supply before servicing; wear gloves and eye protection.
• Access the tub cover per service instructions; release the retainer ring/clips to remove the cover and old seal.
• Clean and dry all mating surfaces; remove residue so the new seal seats evenly.
• Lightly moisten the new seal, install uniformly around the rim, reinstall the cover/retainer, and run a short test with water to check for leaks.

This replacement bolt secures internal components in your appliance. A stripped, rusted, or missing bolt can let parts loosen and vibrate; installing a new bolt restores a tight, stable connection for reliable operation.

• Provides a secure, threaded fastener for brackets, weights, or assemblies
• Helps maintain alignment and reduce movement during operation
• Typical issues: missing hardware, stripped threads, or visible corrosion
• Helps address rattling or excessive vibration caused by loose hardware

• Safety first: Disconnect power; for water- or gas-connected units, shut off supplies
• Support the component being secured before removing the old fastener
• Start threads by hand to avoid cross-threading; tighten evenly to manufacturer guidance—do not overtighten
• Reuse original washers/spacers and thread locker only if they were originally present

This genuine replacement spring restores proper tension and smooth movement in the affected mechanism, helping your appliance operate reliably. Replacing a weakened or broken spring can reduce noise and correct misalignment caused by lost tension.

• Maintains tension and provides return force for connected levers, brackets, or linkages
• Helps keep components in position and minimizes excess play or rattling
• A weakened, stretched, or broken spring can cause poor engagement or inconsistent operation
• Common signs include parts not returning to rest, excess slack, or new noises from the area

• Disconnect power; also shut off water supply
• Note the spring's hook orientation and routing; take a reference photo before removal
• Control the spring with pliers and wear gloves/eye protection to avoid snap-back injuries
• Inspect related brackets/retainers and replace any worn components to ensure proper tension

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening

This replacement drive motor restores the appliance's drive function so the drum/blower or other driven component can rotate normally. Use it when the unit fails to start or loses normal rotation. What it does:

• Spins the appliance's drive assembly so the drum, blower or driven component can operate
• Stops symptoms like no rotation, intermittent operation or loud humming from a stalled motor
• Provides the mechanical torque needed to resume normal cycle operation
• Works as the direct drop-in motor when listed as the factory part number

• Disconnect power before removing the old motor; follow lockout/tagout and manufacturer safety guidance
• Compare the part number and mounting/connector details before installing
• Reuse any brackets or hardware only if they match OEM specifications; replace damaged mounting hardware
• If electrical connectors, capacitors, or mounts differ, do not force fit—verify correct components and wiring

This lid strike mounts to the washer lid and engages the lid lock/switch when the lid is closed. It signals the control that the lid is shut so the cycle can start and spin safely without interruption.

• Engages the lid lock/switch to confirm the lid-closed status
• Allows cycles to start and spin once the lid is shut
• Typical failure symptoms: washer won't start or spin; lid won't lock; strike is broken or missing
• Restores reliable lid engagement and safety interlock operation

• Unplug the washer before servicing
• Open the lid and remove the damaged strike from the lid (retain any screws if present)
• Align and secure the new strike; ensure it lines up with the lid lock opening
• Close the lid to verify smooth engagement before restoring power

This spring restores tension to the door lock mechanism so the latch returns to its proper position after operation. A worn or missing spring can cause a loose latch, difficulty locking, or a door that won't stay secured during a cycle.

• Returns the door lock latch to its resting position
• Helps ensure the door locks securely during operation
• Symptoms can include a floppy/loose latch, intermittent lock errors, or door not staying latched
• Also helps resolve issues where the door won't unlock smoothly

• Disconnect power before servicing
• Access the door lock assembly per your model's service procedure
• Note spring orientation during removal; install the new spring in the same positions
• Latch operation by gently opening/closing the door before reassembling

This is a suspension spring for select washers. It supports and stabilizes the wash tub during spin and agitation to reduce vibration and noise, helping the machine run smoothly.

• Supports the tub within the cabinet to control movement
• Helps reduce excessive vibration, banging, or walking during spin
• Addresses symptoms like out-of-balance loads, noise, or shaking
• Loss of tension, stretching, or breakage can require replacement

• Unplug the washer and shut off water supply before repair
• Access typically requires removing the top or front panel; support the tub to relieve spring tension
• Wear gloves and eye protection; springs are under tension
• Replace any damaged or missing suspension components in pairs or as required.

This retaining ring secures a shaft or component in-place to prevent axial movement and wear, restoring proper alignment and reducing noise or wobble. It's a small, durable replacement part for assemblies that use a snap-style ring. What it does:

• Holds shafts, bearings or components axially in their mating grooves to prevent shifting.
• Stops rattling, grinding, or excessive play caused by a worn or missing ring.
• Keeps assemblies aligned to reduce premature wear on surrounding parts.
• Provides a simple replacement solution when the original ring is bent, broken, or lost.

• Disconnect power and/or water and remove any panels needed before starting work.
• Use snap-ring pliers or the manufacturer-recommended tool to safely remove and install the ring.
• Inspect grooves and mating surfaces for damage or debris and clean before installing the new ring.
• Wear eye protection and keep fingers clear—snap rings can spring out during removal or installation.

This strike screw secures the door strike/catch to the appliance, keeping the latch aligned so the door closes firmly and any safety interlock engages. Replacing a missing, stripped, or corroded screw helps restore reliable, consistent door latching. What it does:

• Fastens the strike/catch to the door or cabinet
• Maintains proper alignment for positive latch engagement
• Helps address issues like door not latching, loose/rattling door, or intermittent door switch activation
• Replace if threads are stripped, the head is damaged, or the screw is missing

• 1 strike screw

• Disconnect power before servicing; allow hot surfaces to cool. For gas appliances, also shut off the gas supply.
• Support the door or strike and remove the damaged/missing fastener.
• Start the new screw by hand to avoid cross-threading; tighten snugly without overtightening.
• Verify door alignment and latch/lock operation after installation.

Tub to pressure switch hose.

This replacement shield is a direct-fit protective cover that restores the appliance's factory protection for internal components. It prevents contact with sensitive parts and helps keep wiring and controls clear of debris. What it does:

• Protects wiring, controls and nearby components from heat, moisture and debris.
• Restores the original barrier that helps prevent accidental contact with moving or hot parts.
• Replaces cracked, broken or missing shields that can lead to rattling, exposed components or interference.
• Helps maintain appliance safety and quiet operation when installed correctly.

• One replacement shield

• Always disconnect power to the appliance before starting any repair.
• Handle replacement shield carefully — edges may be sharp; use gloves and basic hand tools.
• Retain and reuse original fasteners unless new hardware is specified; ensure shield is properly seated and secured.
• Do not operate the appliance with shields or covers missing.

This factory replacement screw secures panels, brackets, or trim on your appliance so parts stay tight and aligned. Swap in a new screw when one is missing or stripped to restore a solid, rattle-free fit.

• Fastens compatible panels, brackets, handles, or internal hardware
• Helps maintain proper alignment and stability
• Common fix for loose or wobbly handles/trim, rattling noises, or missing hardware
• Replace if threads are stripped, head is damaged, or corrosion is present

• Disconnect power before servicing; wear cut-resistant gloves
• Use the correct screwdriver or nut driver to avoid stripping
• Start threads by hand to prevent cross-threading
• Tighten until snug; do not overtighten

This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:

• Secures trim pieces, panels, or grill components to the appliance frame
• Prevents loose or rattling parts that can cause noise or misalignment
• Holds components in correct position so doors and panels close properly
• Replaces worn or broken clips that no longer grip reliably

• Remove power or disconnect the appliance before servicing when applicable
• Clip installs by snapping into pre-existing mounting hole or slot; no special tools usually required
• Inspect mating surfaces and replace any additional damaged fasteners for best fit