Pdt285jj2ss Parts

The UI Control Assembly is an OEM part for GE dishwashers. It manages all the electronics and user interface components on the control panel. This assembly includes the control board that directs water temperature, wash cycles, and more based on user selections. 

Causes of a bad UI Control Assembly can include water damage from leaks, failure of electronic components over time, or issues with the control panel buttons or display. 

Symptoms of a bad UI Control Assembly include:

• The dishwasher not starting or not responding to selections
• Inability to change settings or cycles 
• Error codes appearing on the display
• Unresponsive or non-functioning buttons

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Keep your dishwasher's pump protected. This glass trap sits in the sump and captures broken glass and large debris before it reaches the wash motor and spray system, helping maintain water flow and consistent cleaning performance.

• Traps shards and hard debris in the sump to protect the wash motor and pump
• Helps maintain proper water circulation and spray pressure
• A clogged or damaged trap can cause poor cleaning or grit left on dishes
• Grinding or rattling from the sump area may indicate debris in a compromised trap
• If the trap won't seat or lock, debris can bypass filtration

• Disconnect power and water; wear cut-resistant gloves to handle broken glass and sharp debris
• Remove the lower rack and, the lower spray arm; unlock and lift out the old trap
• Clear all debris from the sump; inspect sealing surfaces and nearby filter components
• Seat the new trap fully and lock it in place; reassemble and run a quick test for proper operation

The Turbidity Sensor Assembly is an OEM part for GE dishwashers. It is responsible for monitoring the cleanliness of the water during the dishwashing cycle. The turbidity sensor measures the level of particles and impurities in the water, allowing the dishwasher to adjust the cycle accordingly. It helps prevent issues such as over-washing or under-washing, resulting in clean dishes every time.

A bad Turbidity Sensor Assembly can lead to improper cleaning performance or cycle errors. Causes of a bad turbidity sensor can include sensor malfunction, damage to the sensor, or buildup of residue affecting its accuracy.

Symptoms of a bad Turbidity Sensor Assembly include:

• Incomplete or inadequate cleaning of dishes
• Error codes related to water cleanliness or turbidity
• Extended or shortened cycle times without reason
• Persistent residue or film on dishes after the cycle

Replace your faulty or damaged Turbidity Sensor Assembly with this genuine OEM GE part to ensure precise cleaning performance and spotless results. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This Insulation Bag Assembly is an OEM part for GE dishwashers. It's designed to provide sound insulation and heat retention, enhancing the overall efficiency and noise reduction of the dishwasher. The insulation bag plays a vital role in maintaining the optimal operating temperature within the dishwasher while minimizing the sound during its operation. 

Replacement of the insulation bag assembly may be necessary due to wear, damage, or inefficiency in sound dampening or heat retention. A compromised insulation bag can lead to increased noise levels and reduced energy efficiency.

Symptoms of a malfunctioning Insulation Bag Assembly include:

• Noticeably louder operation of the dishwasher.
• The outer surfaces of the dishwasher becomes unusually warm during operation.
• Physical damage or wear to the insulation material.
• Changes in the dishwasher's drying performance due to altered internal temperatures.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This clamp kit replaces worn Piranha-style clamps used in the dishwasher's wash system. Restores a tight, reliable seal on internal connections to help prevent leaks and maintain proper water circulation for consistent cleaning results.

• Secures internal hose and pump connections within the wash system
• Helps stop water leaks caused by loose, stretched, or damaged clamps
• Supports proper circulation and wash performance by keeping joints sealed
• Common symptoms: water under the unit, drips at hose joints, loose connections, vibration or rattling from the sump area

• Disconnect power and shut off the water supply before servicing
• Access the sump/pump area from the front toe-kick or by pulling the unit out as needed
• Replace one connection at a time; position and fully seat the new clamp(s) on clean hose/barb surfaces
• Restore power/water and run a short cycle to check carefully for leaks before reinstalling panels

The Harness Assembly is an OEM component specifically designed for GE dishwashers. As the networking hub of the appliance, the harness assembly is responsible for connecting various electrical components and relaying signals between them. It contains numerous wires bundled together to transmit power and communications throughout the dishwasher. 

Symptoms of a bad harness assembly include: 

• Lights or components not functioning properly
• Error codes displayed 
• The control panel not responding as expected
• Unexpected stopping or failing to start wash cycles

Over time and with repeated heating and cooling during wash cycles, wiring can fatigue and insulation can crack or deteriorate. Choosing this genuine GE replacement harness assembly helps ensure all electrical connections remain solid. It also upgrades to the latest harness design compatible with the most current GE dishwasher models. This OEM part is additionally compatible with Crosley, ASKO, KitchenAid, and select Kenmore dishwashers.
 

This upper wash impeller circulates water to the upper spray system during the wash cycle, helping deliver thorough cleaning across dishes on the upper rack and throughout the tub.

• Drives water flow to the upper spray arm/manifold
• Worn or damaged impeller can cause weak spray, poor cleaning, or longer cycle times
• Physical damage (warping, cracks, stripped splines) warrants replacement

• Disconnect power and water before servicing
• Access is typically through the sump/pump area; note impeller orientation during removal
• Inspect mating parts (seal, hub, shaft/splines) and replace if worn
• Hand-tighten fasteners to OEM guidance and verify free rotation before reassembly

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

Size: 8-18 AB TSQ 5/8 SS

This is a machine screw used to secure dishwasher components. The 10-32 thread and 3/8-inch length with an integrated hex washer head provide a firm, vibration-resistant hold to keep parts properly fastened.

• Secures brackets, panels, or internal assemblies in the dishwasher
• Helps prevent looseness, rattling, or misalignment during operation
• Common symptoms of a missing/stripped screw include panel movement, vibration, or loose mounting points

• Disconnect power and shut off water before servicing
• Use the correct nut driver or socket to avoid stripping the head
• Replace any damaged or missing screws in matching locations
• Do not overtighten; snug to manufacturer's torque guidance when available

This dishwasher hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal during operation. Replacing a worn or corroded clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place.

• Secures dishwasher hoses to fittings on pumps, valves, or drain outlets
• Helps prevent water leaks at hose connections
• Keeps hoses from slipping off under vibration and water pressure
• Typical symptoms include water under the unit, dampness in the cabinet, or a hose connection that feels loose

• Disconnect power and shut off water supply before servicing
• Access the hose connection (toe-kick or rear/side panels may need removal)
• Seat the hose fully on the fitting, position clamp just behind the barb/ridge, and secure without over-tightening
• Run a short test cycle and check all connections for leaks

This pump isolator hanger secures and cushions the dishwasher's pump assembly, helping reduce vibration and noise while keeping the pump properly supported. Replacing a worn hanger restores stable, quieter operation and maintains correct pump alignment.

• Supports and isolates the pump assembly beneath the tub to dampen vibration
• Helps keep the pump properly positioned and prevents contact/rattling
• Replace if the hanger is stretched, cracked, or broken
• Common symptoms include louder operation, rattling from the base, or a sagging pump assembly

• Disconnect power and shut off water before servicing; wear gloves and eye protection
• Access from the front base by removing the toe-kick/kickplate; support the pump assembly
• Detach the worn hanger from its mounting points and install the new hanger in the same locations
• Ensure the pump is secure, hoses/wires aren't strained, and run a brief test for noise/vibration

This side blaster assembly mounts to the dishwasher's tub wall and directs a focused spray into the wash cavity to help scour stuck-on residue. Replace if the nozzle is cracked, clogged, or leaking to restore proper cleaning performance.

• Provides targeted side-wall spray to supplement the main wash arms
• Helps flush debris and improve coverage along racks and corners
• Common failure signs: weak or no side spray, poor cleaning near the side wall, visible cracks, or leaks at the side jet
• Restores intended spray pattern and water distribution when the original is damaged or blocked

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack to access the side blaster location
• Release the retainer/screw, disconnect the hose/tube, and install the new assembly; ensure the sealing surface is clean and properly seated
• Reconnect, secure, and run a test cycle to check for leaks and proper spray

Size: 10-32 GXTT FLP.595 S

The Rack Slide End Cap is an OEM replacement part for GE dishwashers. These end caps are installed on either side of the upper and lower dish racks to facilitate smooth gliding movement while preventing any snags. 

Causes of bad rack slide end caps can include wear and tear from repeated use, damage from impact of dishes, or cracks/breaks which reduce functionality. 

Symptoms of bad rack slide end caps include:

• Difficulty sliding racks in and out 
• Loud squeaking or grinding noises during rack movement
• Misalignment of dish racks  
• Dishes unable to fit properly due to movement restrictions

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dishwasher main control board kit replaces the electronic "brain" that drives each cycle. It restores proper sequencing and reliable power to key components so wash programs run correctly when the original board has failed.

• Coordinates cycle timing and routes power to the circulation pump, drain pump, inlet valve, and heater
• Interprets signals from sensors and the user interface to start, advance, and complete cycles
• Common signs of a failing board include: dishwasher won't start or is unresponsive; stops mid-cycle or won't advance; erratic/blank display; inconsistent filling, draining, or heating

• Disconnect power at the breaker and shut off water before servicing
• Use ESD precautions; handle the board by its edges and avoid touching terminals
• Photograph/label connectors and transfer any model-specific jumpers or mounting hardware from the old board
• Seat all harnesses fully; restore power and run a test cycle to verify operation