Pdt525ssj0ss Parts

Arm hinge assembly is the pivoting hinge that supports and guides the appliance door, restoring smooth, stable opening and closing for proper alignment and operation. Replacing a worn hinge helps stop sagging, misalignment, and scraping noises. What it does:

• Supports the door pivot and maintains proper hinge alignment for smooth opening/closing.
• Helps the door latch and seal correctly by keeping the door level and aligned.
• Common symptoms: door hangs or sags, door won't close or latch, rubbing or scraping noises during movement.
• Replaces a bent, worn, or broken hinge arm to restore normal door operation.

• Disconnect power before starting any service.
• Use proper hand tools and support the door while removing/installing the hinge to avoid damage or injury.
• Align the hinge and operate the door several times before fully tightening fasteners; follow manufacturer torque/fastening guidance if available.

This conduit assembly carries wash water from the pump to the dishwasher's tiered spray system for consistent rack coverage. Replace a damaged or clogged conduit to restore spray performance and minimize leaks or spray loss inside the tub.

• Channels water to the upper/tiered spray jets for proper coverage
• Helps maintain correct flow and spray pressure to the upper wash system
• Common symptoms: poor cleaning on the upper rack, weak/no spray from upper jets, or leaks/spray from the rear conduit area
• Visible cracks, warping, or broken tabs can prevent a tight, leak-free seal

• Disconnect power and shut off the water supply before servicing
• Remove racks as needed; release interior screws/tabs to detach the conduit and note original orientation
• Seat all connections and seals fully to prevent leaks; secure mounting points
• Run a short test cycle and check for leaks and proper spray action

Restore proper wash performance with this turbidity sensor. It reads the clarity of the wash water so the control can adjust cycle length, fills, and rinses automatically for efficient, consistent cleaning. What it does:

• Monitors water clarity/soil level via an optical sensor in the sump
• Sends data to the control to optimize wash time, rinses, and water use
• Failure can cause unusually long or short cycles or failure to advance
• Contribute to poor cleaning results or repeated fills/drains

• 1 turbidity sensor

• Disconnect power and shut off water supply before servicing
• Access the sensor from the bottom/front of the tub at the sump area; removing the toe-kick or pulling the unit forward may help
• Release the locking tab/twist-lock, unplug the connector, and transfer the existing seal if needed
• Seat the new sensor fully, reconnect wiring, restore utilities, and run a short cycle to check for leaks and normal operation

This coated fold-down tine replaces a damaged or missing tine in a dishwasher rack to help secure dishes and allow the tine to fold down for larger items. The coated finish helps protect dishes and resist chipping. What it does

• Supports plates, bowls and glassware in the rack so items stay upright during a cycle
• Folds down to create clearance for taller or bulky items like pots and stemware
• Coated finish helps reduce scratching and corrosion on fragile items
• Use when a tine is bent, broken or no longer holds dishes securely

• Remove dishes and utensil baskets before replacing the tine
• Usually snaps into the existing rack slot or hooks into place; inspect adjacent clips and retainers
• No special tools typically required; use gloves to protect hands from sharp edges
• If rack coating or retainers are damaged, replace those parts to ensure a secure fit

This bottle blaster assembly supplies targeted wash water to the dishwasher's Bottle Jets to clean tall, narrow items like baby and sports bottles. Replace a damaged or clogged assembly to restore focused spray and top-rack cleaning performance. What it does:

• Routes wash water to the bottle jet nozzles for concentrated cleaning inside bottles and narrow openings
• Helps improve cleaning on items positioned over the Bottle Jets
• Failure symptoms include no spray from the bottle jets, poor upper-rack cleaning, leaks near the jet area, or visible cracks/damage

• 1 bottle blaster assembly

• Disconnect power and shut off water to the dishwasher before servicing
• Access the bottle jet area; release retaining clips/fasteners and note hose routing and connection points
• Transfer any reusable clips or seals from the original assembly if needed
• Fully seat connections; run a short cycle to check for leaks and proper jet spray

This drain hose elbow creates a secure 90-degree connection in the dishwasher's drain line, helping route the hose cleanly while maintaining good flow. It supports a tight, leak-resistant turn where space is limited, reducing kinks and misrouting.

• Provides a 90-degree turn for the dishwasher drain hose to aid proper routing and flow
• Helps reduce kinks or crushing at tight bends that can slow or stop draining
• Forms a secure connection point to help prevent leaks at the hose junction
• Common symptoms of a failed or damaged elbow include leaks under the sink, visible cracks, kinks, or slow/poor draining

• Disconnect power and water supply; place a towel or pan to catch residual water
• Ensure the hose is fully seated on the elbow and secured with appropriate clamps per your model
• Route the drain line with a high loop or air gap as required by local code
• Run a short cycle and check all connections for leaks

A coated fold-down tine for dishwasher racks that restores secure dish support and lets the rack fold down to accommodate larger cookware. The protective coating helps resist corrosion and reduces scratching of dishes. What it does:

• Replaces a broken or missing fold-down tine so dishes sit securely on the rack
• Folds down to create extra space for large pots, pans, or baking sheets
• Coated finish helps resist rust and prevents metal-to-dish contact
• Helps stop dishes from tipping or sliding when the original tine is damaged

• High-level replacement: typically snaps into the rack; inspect surrounding tines and rack clips for wear
• Always disconnect power to the appliance and empty the rack before servicing
• Handle the coated surface carefully to avoid chipping the finish; reinstall rack per manufacturer guidance
• If the rack or mounting hardware is damaged, replace those components to ensure a secure fit

The Upper Rack Bracket Assembly is an OEM replacement part for  GE dishwashers. It is located inside the dishwasher tub and functions to securely mount the upper dish rack. It allows for adjustable height positioning and prevents rack movement during washing.

Causes of a bad upper rack bracket assembly can include cracks or breaks in the mounting points, stripped screw holes allowing rack sway, or deformities preventing proper seating.

Symptoms of a bad upper rack bracket assembly include: 

• Loosening or detaching of the upper rack during the cycle  
• Restricted rack adjustment or inability to set desired height
• Noise or vibration from an unsecured rack vibrating against the tub

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Console Top Control is an OEM replacement part for GE dishwashers. It is located at the top center of the dishwasher console and is responsible for operating all cycle and option buttons via touch controls. 

Causes of a bad console top control can include cracks or breaks in the physical buttons/display, malfunctions in the electronic control board, or water damage.

Symptoms of a bad console top control include:

• Unresponsive or stuck buttons  
• Inaccurate or intermittent cycle/setting displays
• Repeated cycle error messages
• Complete lack of responsiveness requiring hard reset

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This replacement middle spray arm and gasket assembly restores strong, even water spray to the center level of your dishwasher. It replaces a cracked, clogged, or loose arm/seal that can leave dishes dirty and reduce wash performance.

• Directs pressurized wash water through jets to clean items on the middle rack
• Seals the connection to maintain pressure and proper rotation
• Helps ensure full spray coverage and consistent cleaning results
• Recommended when the arm is cracked, warped, clogged, or not spinning
• Can help with poor cleaning on the middle/upper rack or rattling from a loose arm

• Disconnect power and shut off water supply before servicing
• Open the dishwasher, remove the rack if needed, and release the old middle arm from its hub
• Seat the new gasket fully, install the arm, and secure any reused retainer/clip
• Spin the arm by hand to confirm free rotation and clearance; run a short test cycle

This is a 6-20 machine screw, 3/8 inch length, used to secure trim, panels, or small components on compatible cooking appliances. Replacing a missing or damaged screw helps keep parts tight and prevents rattles or shifting during use.

• Fastens brackets, panels, or trim in the appliance chassis
• Helps restore a secure fit when the original screw is stripped or lost
• Can resolve issues like loose trim, minor rattling, or misaligned panels
• Nickel finish for corrosion resistance in warm, humid environments

• Disconnect power and allow appliance to cool before servicing
• Remove only the necessary adjacent fasteners to access the mounting point
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Replace any missing clips or spacers originally used with the screw

This detergent plate is the replacement dispenser component that holds and releases detergent during the wash cycle, ensuring detergent is delivered when the machine runs for proper cleaning performance. What it does

• Holds detergent inside the dispenser area until the wash cycle calls for release.
• Opens or allows detergent to be flushed into the wash chamber at the correct time.
• Common symptom: detergent stays in the dispenser and doesn't release, leaving dishes or laundry soiled.
• Common symptom: damaged, cracked or warped plate can prevent proper release or seating of detergent.

• One detergent plate

• Disconnect power (and water if applicable) before accessing the dispenser to avoid shock or injury.
• Handle the plate carefully; plastic parts can crack if forced or over-tightened.
• Remove the door/dispenser trim per your model's service instructions to access the plate; reinstall ensuring proper alignment so the dispenser seals and operates correctly.

The Vent Fan Assembly is an OEM replacement part for GE dishwashers. As a key ventilation component, the vent fan is responsible for drawing moisture-laden air out of the dishwasher tub and venting it outside during and after the wash cycle. It plays an important role in effectively drying dishes and preventing mold or odor issues.

Causes of a bad vent fan include a failing motor, broken or cracked fan blades, or an obstructed vent opening. 

Symptoms of a bad vent fan include:

• Incomplete or slow drying of dishes
• Excess moisture remaining in the tub at the end of the cycle  
• Mold or mildew growth inside the dishwasher
• Strange noises or vibrations coming from the vent area

Over time, the vent fan motor and blades can degrade due to continuous use. This part is also compatible with ASKO, Crosley, Inglis, Magic Chef, RCA, and some Kenmore models.
 

This 10-32 x 1/4-inch zinc-plated screw secures internal panels and hardware in select dishwashers. Replace a missing, stripped, or corroded fastener to restore a tight fit and help prevent vibration or loosening during operation.

• Fastens brackets, panels, or components that use a 10-32 machine thread
• Replaces hardware that is missing, stripped, or rusted
• Helps reduce rattling or vibration from loose assemblies
• Supports proper component alignment for reliable operation

• Disconnect power and water supply before servicing the appliance
• Remove the old fastener and verify thread size and length match before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace damaged clips, nuts, or inserts that won't hold a 10-32 screw securely

This fixed dishrack bracket secures one end of a rack component (such as a fold-down tine row), keeping it anchored during wash cycles. Replace a cracked or missing bracket to restore stable support and reliable rack function.

• Anchors a rack component to the dishrack in a fixed position
• Helps keep dividers/tines aligned so dishes stay upright
• Replaces a broken, worn, or missing bracket
• Symptoms may include loose or collapsing tines, dishes tipping, or visible bracket damage

• Unload and extend the rack; remove the rack if needed for access
• Release the locking tabs/clips and remove the damaged bracket
• Align the new bracket and snap/slide it fully into place until it locks
• Verify a secure fit and smooth rack movement; wear gloves to protect hands
• Some racks use both fixed and adjustable brackets—confirm the side you need before ordering

This flood float and switch assembly senses the dishwasher's water level and signals the control to stop filling at the proper point, helping prevent overfilling and leaks while restoring consistent, correct fill for reliable wash performance.

• Senses rising water level via a float and actuates the switch
• Signals the control to stop water flow when the set level is reached
• Failure symptoms include no fill, continuous filling/overfilling, intermittent filling, or continuous draining at startup
• Restores proper water-level protection and helps prevent leak damage

• Disconnect power and shut off water supply before servicing; wear cut-resistant gloves
• Access is typically from the lower front/toe-kick area; remove panels to reach the float/switch housing
• Move wire connections one at a time to the new assembly; ensure the float moves freely after installation
• Run a brief fill test and inspect for leaks before fully reassembling