Pdt845sblts Parts

This leak sensor mounts in the appliance's drain/drip pan to detect unwanted water and alert the control system, helping prevent overflow and water damage. It's a direct-fit replacement designed to restore pan leak detection. What it does:

• Detects water accumulation in the pan and signals the appliance control to respond
• Helps identify leaks that cause pooling under the appliance
• Can stop or trigger diagnostics before water reaches floors or cabinetry
• Compatible with the original pan wiring and connector layout

• Disconnect power to the appliance before servicing to avoid shock or damage
• Locate and access the pan area; handle the sensor and wiring gently
• Ensure proper connector seating and secure routing so the sensor contacts the pan surface
• Test the sensor and appliance after installation

This rubber grommet provides a protective seal where hoses, wires or components pass through openings, helping prevent chafing and moisture intrusion. Use it to restore a tight fit and reduce wear at the penetration point. What it does:

• Seals and cushions openings to help prevent water leaks and air gaps.
• Protects wiring and hoses from rubbing on sharp metal edges that can cause wear or shorts.
• Reduces vibration and rattling by holding parts securely in place.
• Common symptoms of failure: visible cracking, missing or torn grommet, water dripping near the opening, or rubbing noises.

• Disconnect power to the appliance and turn off water supply before beginning any repair.
• Remove the access panel or boot as needed to reach the opening; press the grommet into the hole until fully seated.
• Inspect surrounding seals, hoses and wiring; replace any damaged components to prevent repeat issues.

This SCR 8-18 silicon-controlled rectifier replaces the control semiconductor that switches and regulates power to heating or motor circuits in compatible appliances, restoring proper power delivery and control. It's a direct-fit electrical replacement part. What it does

• Acts as a switching device on control boards to allow or block current flow when signaled.
• Regulates power delivered to heating elements or motor circuits to enable proper operation.
• Commonly linked to symptoms like no heat or intermittent heating, motors that won't start, or erratic control-board behavior.
• Helps restore reliable on/off control when a failed SCR is causing open or shorted conditions.

• One SCR 8-18 silicon-controlled rectifier (WD02X10160).

• Always disconnect power before servicing the appliance to avoid shock.
• Handle the part carefully; avoid touching leads and use anti-static precautions if available.
• Inspect surrounding connectors and wiring for damage; replace any corroded terminals.

A fixed mounting bracket that secures and stabilizes a component or panel in place, helping prevent movement and vibration for reliable appliance operation. Simple, durable replacement for worn or damaged brackets. What it does:

• Holds a panel, trim, or assembly securely to the appliance frame
• Keeps parts aligned to prevent rubbing, rattling, or misfit
• Restores proper support when an original bracket is bent, cracked, or broken
• Helps reduce noise caused by loose or unstable components

• Disconnect power (and water if applicable) before starting work
• Use the factory fasteners or equivalent-size screws to secure the bracket
• Inspect mating surfaces and hardware for damage; replace any stripped screws

This vent conduit assembly routes exhaust from the dryer to the home vent, restoring proper airflow and helping the appliance vent safely. It replaces a damaged, crushed, or disconnected dryer vent channel to improve drying performance and reduce lint buildup. What it does:

• Channels dryer exhaust from the appliance to the wall vent
• Prevents restricted airflow caused by crushed or separated vent tubing
• Helps reduce long dry times and overheating symptoms
• Lowers risk of lint buildup and related odors near the dryer

• Disconnect power (and gas supply for gas dryers) before beginning service
• Verify correct alignment and secure with appropriate clamps or fasteners
• Inspect adjacent venting and clean lint from vent path while replacing

A silicon-controlled rectifier (SCR) used on appliance control boards to regulate power to motors, igniters or other loads. Replacing a faulty SCR can restore proper power switching and steady operation of the driven component. What it does:

• Acts as a power-switching semiconductor in appliance electronic control circuits to allow current flow only when triggered.
• Enables controlled delivery of voltage/current to motors, igniters and similar loads on the control board.
• A failing SCR can cause symptoms such as no power to a motor or igniter, intermittent operation, or complete failure of the driven component.
• Match the SCR package and electrical ratings to the control board before replacing.

• Disconnect all power to the appliance before accessing control electronics to avoid shock or damage.
• Take electrostatic-discharge (ESD) precautions; handle the SCR by its body and avoid touching leads.
• Package orientation and electrical ratings on the control board and wiring before installation.

This is a stainless steel hex washer-head screw used to fasten and secure components. Its integrated washer head provides a broad bearing surface for a tight, durable hold in appliance assemblies.

• Secures panels, brackets, and hardware to prevent looseness and vibration
• Restores proper fastening when originals are stripped, missing, or corroded
• Stainless construction helps resist rust in moisture-prone areas
• Common symptoms of a needed replacement include rattling, loose panels, or missing hardware

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct nut driver or socket for the hex head to avoid stripping
• Replace any damaged or missing fasteners in matched pairs or sets for even clamping
• Do not overtighten; snug to manufacturer torque guidance when available

This floor plate is the OEM-style replacement that fits under the oven cavity to protect internal components and provide a stable cooking surface. Restores proper support and helps maintain even heat distribution in the lower oven area. What it does

• Covers and protects the oven's lower cavity from spills, drips, and falling debris
• Helps funnel heat and airflow for more consistent baking and roasting performance
• Prevents direct contact between food/drips and heating components
• Reduces corrosion and wear to inner oven parts caused by spills

• One floor plate as shown

• Designed to be installed in the lower oven cavity; for exact placement
• Remove power (unplug or shut off breaker) and allow the oven to cool before servicing
• Use appropriate gloves to avoid sharp edges; avoid forcing the part into place

This block foam door is an insulated panel that fits inside the appliance door to help reduce heat transfer and maintain consistent internal temperatures. It restores door insulation for more efficient cooling and temperature stability. What it does:

• Provides thermal insulation inside the door to reduce heat gain or loss
• Helps prevent frost buildup and cold spots by improving temperature consistency
• Supports efficient compressor cycling and can reduce energy waste when functioning properly
• Common symptom: uneven temperatures, visible condensation or frost on the door, or reduced cooling performance

• One block foam door

• Disconnect power before servicing and follow the appliance manufacturer's disassembly instructions
• May require removing the inner door liner and fasteners to access and replace the foam; keep hardware for reassembly
• Handle carefully to avoid damaging the foam or door liner; use appropriate hand protection

This bracket handle is the replacement mounting bracket that secures a refrigerator or freezer door handle, restoring proper handle alignment and a secure grip. It helps keep the door handle firmly attached and functioning. What it does:

• Secures the door handle to the appliance door so the handle stays mounted and aligned
• Restores a loose, wobbly, or detached handle for reliable opening and closing
• Prevents further wear on handle fasteners by providing the proper mounting support
• Matches OEM fit and function for straightforward replacement

• One replacement bracket handle

• Basic hand tools typically required; handle hardware may need removal first
• Follow OEM instructions and use correct fasteners; replace any damaged screws or anchors
• Disconnect power to the appliance (or keep door open/unloaded) and work safely to avoid pinching or dropping the door

This latch cam engages the door latch mechanism so the appliance door closes and stays secure during cycles. A worn or broken cam can prevent the door from latching or cause the door to feel loose. What it does

• Rotates with the latch to lock the door securely during operation
• Ensures the latch striker catches and holds the door closed
• Common symptom: door won't stay latched or appliance won't start
• Common symptom: door feels loose, noisy, or intermittently opens during cycles

• One latch cam

• Disconnect power before starting any repair to avoid shock or injury
• Inspect surrounding latch components and replace any visibly damaged parts
• Use basic hand tools; keep track of small fasteners and alignment during reassembly
• Test door operation several times after installation to ensure secure engagement

This fill hose routes incoming water from the household supply into the washer. It replaces cracked, split, or leaking inlet hoses to restore proper water fill and help prevent leaks during the wash cycle. What it does

• Connects the home water supply to the washer's inlet valve to allow normal water fill.
• Replaces damaged or deteriorated hoses that drip, spray, or fail to maintain water flow.
• Helps eliminate visible leaks and reduces the risk of water damage around the appliance.
• Restores reliable fill performance when the original hose is worn, swollen, or split.

• Turn off water supply and unplug the washer before starting installation.
• Confirm correct hose orientation and thread type before tightening to avoid cross-threading.
• Hand-start threads, then snug with a wrench—do not overtighten; check all fittings for leaks after restoring water.
• Inspect inlet valve and fittings; replace any corroded or damaged connectors for a secure seal.

This replacement lower dishrack restores smooth rolling and secure loading on the bottom level of your dishwasher, helping plates, bowls, and pots stay in place for consistent spray coverage and reliable cleaning results. What it does

• Organizes and supports dishes, cookware, and utensils on the lower level during wash and dry cycles
• Rolls in and out on the tub rails for easy loading and unloading
• Positions items for effective spray coverage and drainage
• Replace if tines are broken, coating is peeling/rusting, the rack derails or won't roll smoothly, or items tip over

• One lower dishrack

• Turn off power to the dishwasher before servicing
• Pull the old lower rack straight out; release/remove any rack stops if present
• Transfer any removable accessories from the old rack (such as utensil basket or clips), if needed
• Slide the new rack onto the rails and verify smooth operation

This high loop drain hose creates the required elevated drain loop to help prevent dishwasher backflow and ensure proper drainage. It replaces a worn or damaged drain loop and restores correct drain routing for reliable performance. What it does:

• Forms the high loop in the dishwasher drain line to reduce risk of sink water siphoning back into the appliance
• Directs wastewater from the dishwasher into the household drain properly
• Helps avoid intermittent draining issues caused by a collapsed or split drain loop
• Fits into existing drain connections—used where an elevated drain loop is required

• Designed for in-line replacement; route the hose to create a high loop secured under the countertop or cabinet as shown in the appliance installer instructions
• Turn off power and water supply to the appliance before performing service
• Inspect clamps and fittings and replace if corroded; ensure all connections are snug but not over-tightened

The Turbidity Sensor is an OEM part for GE dishwashers. It is a water quality monitor that detects small food particles in the rinse water during dishwashing cycles. The sensor plays an important quality control role by ensuring water has achieved the necessary clarity before terminating the rinse phase.

Symptoms of a bad turbidity sensor include:

• Incomplete or unsatisfactory rinsing results
• Cycles not advancing properly beyond the rinse stage
• Error codes related to turbidity detection

Causes can be mineral deposits interfering with the sensor's ability to transmit light through the water, or failure of the electronic components over time.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

TRANSITION PIECE ASM