Pdw7880 Parts

Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.

Genuine Ge part

Seat Check Valve

By: Ge

Part Number: WD01X10176

Genuine Ge part

Pulley Cable Asm

4.0 (1)

By: Ge

Part Number: WD01X24276

Do-It-Yourself Stories from Customers like You Dishwasher broken door spring assembly William G. • Las Vegas , NV • September 24, 2019

Went on the internet, located the part on your website and ordered 2 items. Read more

Genuine Ge part

Trim Tub Flange Bk

By: Ge

Part Number: WD08X10021

Genuine Ge part

Conduit Spray Arm Mid

4.5 (2)

By: Ge

Part Number: WD12X10052

Do-It-Yourself Stories from Customers like You Bottom rack was rusting out and the middle sprayer was not spinning Charles B. • Rockwall , TX • July 29, 2016

Replaced the rack, the replacement was already fully assembled. Replacing the middle sprayer and assembly wasn't too bad. Read more

Genuine Ge part

Grommet Heater

5.0 (2)

By: Ge

Part Number: WD01X10094

Do-It-Yourself Stories from Customers like You Leaking water Stephen M. • Vineland , NJ • April 19, 2021

This was not an obvious source of a leak. The Tower Heater Assembly Nut developed a crack over time due to heat exposure. So the leak was gradual slowly getting worse over time. It was a hairline crack that ran down one of the edges of the nut making it hard to see. In talking to a pro he said it isn't a common problem. It is all the way in the back of the bottom of the dishwasher so it is not something you can see without pulling the dishwasher out and running it. The repair itself is easy. I... Read more

Genuine Ge part

Turbidity Sensor (Washer)

By: Ge

Part Number: WD21X10272

This turbidity sensor monitors wash water clarity so the machine can adjust wash cycles and rinse times for cleaner results and efficient water use. It replaces a failed or inconsistent turbidity reading to restore proper load sensing. What it does:

Detects soil level/turbidity in wash water so the washer adapts cycle length and rinse actions
Helps prevent over- or under-washing by feeding water-quality signals to the control board
Commonly replaces units that cause long or short cycles, poor cleaning, or error codes related to wash sensing

What's included: One turbidity sensor Install notes:

Disconnect power before replacing to avoid shock or damage to electronics
Handle the sensor and connectors carefully; avoid contaminating sensing surfaces
Verify connector orientation and secure mounting; test a short cycle after installation

Genuine Ge part

Gripper Stemware

5.0 (1)

By: Ge

Part Number: WD28X10181

Do-It-Yourself Stories from Customers like You Missing top shelf retainer and broken stem glass holders Stewart M. • Middletown , CT • September 19, 2016

Replaced the parts. Read more

Genuine Ge part

Bearing Spray Arm Mid

5.0 (3)

By: Ge

Part Number: WD01X10108

Do-It-Yourself Stories from Customers like You Leaking water onto the floor John G. • Canmer , KY • May 28, 2015

The main conduit was broken and the pump connector had a hole in it. The pump also was showing signs of leaking. I completely disassembled the dishwasher cleaned everything and reassembled. The repair videos are a big help. Thank you. Read more

Genuine Ge part

Spray Arm Water Supply Tube

5.0 (5)

By: Ge

Part Number: WD12X10113

Do-It-Yourself Stories from Customers like You The dishwasher was severely covered with calcium and lime the glassware and silverware were coming out with a lot of spotting Peter G. • Niceville , FL • October 18, 2016

I used lime away, vinegar, finish washer cleaner none of them worked. Finally just use Brillo on the entire cabinet interior. It came out very clean. Only needed very light scrubbing. Then replaced the severely corroded filters Riser tube and upper jet which was not turning. After this the upper arm turned perfectly silverware and glassware and silverware came out rinse very clean. Will do preventative maintenance in the future. Dishwasher was about 5 years old GE Profile high-end Read more

Genuine Ge part

Vent

5.0 (1)

By: Ge

Part Number: WD12X10045

Do-It-Yourself Stories from Customers like You The vent part was broken and woulkd not stay in its place and kept falling out the rinse aid cap was broken also and ended up falling on the he4ating element and burnt Martha R. • Spring , TX • February 08, 2015

This was very simple. Thgey just popped back into place asnd the cap screws in. Read more

Genuine Ge part

Comb Retainer

5.0 (3)

By: Ge

Part Number: WD12X10064

Color: white. Measures about 1 inch wide by 1-1/2 inches deep.

Do-It-Yourself Stories from Customers like You Dishwasher retainer clips broke Ken J. • Sammamish , WA • April 05, 2015

Replaced retainer clips. Read more

Genuine Ge part

Escutcheon Bowed Ss A

By: Ge

Part Number: WD34X11233

Genuine Ge part

Nut Tower Heater

By: Ge

Part Number: WD01X10097

Genuine Ge part

Dishwasher Heating Element

4.9 (8)

By: Ge

Part Number: WD05X10010

This part fixes the following symptoms

Not drying dishes properly

Do-It-Yourself Stories from Customers like You Flashing selection light: i think it fixed the problem by changing out the heating element Michael A. • Henderson , NV • April 19, 2015

Found a service manual that is close enough to my GE dishwasher. Service Manual for GE Dishwasher-EDW4000 was found on the following webpage. http://www.applianceaid.com/pdf/serv-man-EDW4000.pdf Gives enough information to test out the dishwasher. Read it, check out Factory Test Mode. GE should have given this out as a normal User Manual. The usual user manual lack anything to help troubleshoot a problem. Read more