Pdw9200joobb Parts

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

This float dome sits in the dishwasher's float well and rises with the water level to trigger the float switch and stop filling. Replace a cracked or missing dome to restore reliable water-level control and overfill protection.

• Moves up and down with the water level to actuate the overfill/flood switch
• Helps prevent overfilling by signaling the inlet valve to shut off at the correct level
• Guides and shields the float mechanism from dishes and debris
• Common symptoms: broken or missing dome, float sticking, dishwasher won't fill or keeps filling

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the float area on the tub floor
• Lift straight up or twist to remove the old dome; clear any mineral/debris from the float well
• Seat the new dome and run a brief fill test

This water inlet cover replaces a cracked or missing inlet-valve trim to protect and conceal the appliance's water inlet area. It restores a finished look while keeping hoses and valve components shielded from debris. What it does:

• Covers and protects the water inlet valve and hose connections from dust and impact
• Conceals exposed hoses and wiring for a cleaner rear-cabinet appearance
• Helps prevent snagging or accidental contact with the inlet valve assembly
• Reduces debris buildup around the inlet area that can affect connections

• Disconnect power to the appliance and shut off the water supply before starting.
• Usually fastens with a few screws or clips—have a screwdriver or nut driver ready.
• Align cover over the inlet valve area, then secure with the original fasteners.
• After installation, turn water and power back on and inspect connections for leaks.

Color: Black

This mounting nut secures the tower heater assembly in the appliance, keeping the heater stable and properly positioned for safe, efficient operation. Replacing a damaged nut restores secure attachment and reduces rattling or loose components. What it does

• Secures the tower heater assembly to the appliance chassis or mounting bracket
• Helps maintain proper heater alignment for reliable heating performance
• Prevents movement that can cause noise, intermittent contacts, or wear on connections
• Used when the original nut is stripped, corroded, or missing

• One tower heater assembly mounting nut

• Disconnect power to the appliance before attempting any repair
• Use appropriate hand tools; avoid over-tightening which can strip threads or damage the heater assembly

This silicon controlled rectifier (SCR) is the control device that regulates high-current power to heating and motor circuits, helping restore proper operation when the original SCR fails. A direct-fit replacement part for the listed appliance control. What it does:

• Regulates and switches high-current power to heating elements or motor circuits as commanded by the appliance control board.
• Stops or reduces power flow when the SCR fails, which can cause no-heat or intermittent heating.
• Can cause symptoms such as no heating, intermittent operation, or incorrect cycle heating when faulty.
• Works with the main control to protect and time the appliance's heating cycles.

• SCR control

• Disconnect power before servicing to avoid electrical shock.
• Handle the part and wiring carefully; match terminals and mounting to the original unit.
• Follow the appliance service manual or wiring schematic for correct installation and testing.

This vent flapper is the exterior exhaust flap that opens to let dryer air and lint exit and closes to keep weather, pests and drafts out when the dryer is off. It restores proper airflow at the outside vent hood. What it does:

• Opens with dryer airflow to allow exhaust to escape and closes when idle to block outside air.
• Helps prevent backdrafts, pests and rain from entering the vent system.
• Can restore normal drying performance when a stuck or broken flap was restricting airflow.
• Commonly replaced when the flap is cracked, warped, jammed or does not seal.

• One vent flapper/exterior exhaust flap.

• Disconnect power to the dryer (and gas supply if applicable) and work from the outside hood when possible.
• Remove the exterior vent hood or access cover to inspect and replace the flap; basic hand tools required.
• Check that the flap moves freely after installation and seats against its seal to prevent air leaks.
• Clean or repair the ductwork to avoid repeat failures.

This electronic control module assembly manages the dryer's cycle selection, timing and user interface so the dryer runs the selected program reliably. Replaces a failed control board to restore normal operation and controls. What it does

• Receives user inputs and starts selected dryer cycles
• Controls cycle timing, motor and heating signals per program
• Communicates status to the display and keypads/buttons
• Common symptom link: dryer won't start, won't advance cycles, shows control/display errors, or has intermittent operation

• Disconnect power before service to avoid shock—this is an electrical assembly.
• Handle the board by the edges and avoid static discharge; use proper ESD precautions if available.
• Verify harness connections and mounting before powering up; do not force connectors.

This shelf cup is a small replacement cup that secures a refrigerator door shelf in place, restoring shelf stability and preventing items from slipping or the shelf from sagging. It's a direct-fit replacement designed to match the original mounting. What it does:

• Supports and anchors a door shelf or shelf bin to the refrigerator door
• Keeps the shelf level so stored items don't slide or tip
• Replaces cracked, broken, or worn shelf cups that allow shelf movement
• Restores proper alignment and secure seating of the shelf/bin

• Disconnect power only if you must move or tilt the appliance; otherwise remove items from the door and work with the fridge closed
• Remove the affected shelf/bin and detach the old cup
• Press the new shelf cup into place until it seats fully; re-install the shelf/bin and check for secure fit

Specs: 10-32 gxtt flp.59

This is a replacement fastener screw used to secure panels and components on compatible appliances, restoring proper fit and reducing movement. It's a simple, direct replacement when an original screw is missing or damaged. What it does:

• Secures access panels, covers, or internal components to prevent rattling and movement
• Helps maintain proper alignment of parts so doors and panels close correctly
• Replaces missing, stripped, or broken screws that can cause loose parts or noise
• Restores the appliance's original fit where a matching OEM fastener is required

• One replacement screw

• Turn off and unplug the appliance before starting any repair
• Use the correct driver and avoid over-tightening to prevent stripping threads
• If the original screw was holding electrical components, ensure power is disconnected and follow OEM safety instructions

This part is a genuine OEM lower rack assembly made for use with various models of dishwashers.The lower rack assembly slides into the lower portion of the dishwasher to allow the user to easily load the appliance as well as hold the dishes still during the wash cycle and make sure they can be properly cleaned. Over time, this part might become dented, bent, snapped, worn, or otherwise rendered ineffective, requiring replacement. No special tools are needed to replace this part. Simply slide out the old rack and replace it with the new one.This OEM part is manufactured by General Electric and has been sourced directly from the manufacturer. This lower rack assembly is manufactured from high-quality, durable, non-corrosive materials to ensure the best possible quality. It is an authentic replacement part and thus is compatible with various models of dishwashers that have been made by brands that include General Electric, Hotpoint, and RCA.