Pdw9800lbb Parts

This sump clamp secures the dishwasher's sump connection at the base of the tub, helping maintain a tight, leak-resistant seal. Replacing a weakened or corroded clamp can help stop drips and keep the wash system stable.

• Secures the sump connection so it stays firmly in place
• Applies even clamping force to help maintain a watertight seal
• Helps prevent leaks or puddles beneath the dishwasher
• Typical signs include water leaking from the bottom, a loose connection, or a rusted/broken clamp

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick and access the sump area; have towels or a pan ready for residual water
• Loosen and remove the old clamp; inspect mating surfaces and the sump seal/gasket and replace if worn
• Position the new clamp squarely and tighten evenly—do not overtighten; run a brief test and check for leaks

This middle conduit carrier secures the dishwasher's water feed tube so it stays aligned as the rack moves. Replacing a cracked or missing carrier helps restore reliable spray delivery and consistent cleaning performance.

• Secures and guides the middle water conduit/feed tube on the rack
• Keeps the conduit aligned with the rear water port for consistent spray
• Helps prevent rack binding or rattling from a loose feed tube
• Helps with weak spray or poor cleaning on the upper rack when the carrier is damaged

• Disconnect power and turn off water before servicing
• Pull the rack forward; release the old carrier's tabs or fastener and detach from the feed tube
• Snap or fasten the new carrier in place; ensure the conduit seats fully at the rear port
• Verify smooth rack travel and run a brief test cycle to check operation

The comb retainer is the small clip that secures the rack comb/tine row to your dishwasher's rack. It keeps the insert firmly in place so dishes stay upright and wash effectively without the tines coming loose.

• Locks the rack comb/tine insert onto the rack wires to prevent shifting
• Helps keep plates, lids, and cookware upright during cycles
• Restores stability when the original retainer is cracked, worn, or missing
• Common symptoms: comb/tine row loosens or falls off, dishes tip over, or you notice rattling in the rack

• Unplug the dishwasher and shut off the water supply before servicing
• Pull out the rack and note the retainer's orientation for reference
• Release and remove the damaged retainer; align and snap the new retainer securely onto the comb and rack wire
• Confirm the comb/tine row is firmly attached and the rack moves freely before running a cycle

This junction box cover replaces the appliance's electrical access panel to protect wiring and provide a secure entry point for the power cord. It restores a finished, safe electrical connection area and helps prevent exposed wiring. What it does

• Covers and protects the appliance's electrical junction box from dust and accidental contact
• Provides the mounting location and opening for the power cord/strain-relief connection
• Secures wiring and helps keep wire connections contained and stable
• Common symptom: cover cracked, missing, or loose—exposed wires or inability to secure the power cord

• Disconnect power at the breaker or unplug the appliance before servicing electrical parts
• Remove mounting screws from the old cover and replace with the new cover; retain or replace strain relief as needed
• Inspect the cord and wiring while access is open; replace any damaged wiring or strain relief components
• Follow the appliance manufacturer's instructions and local electrical codes for safe installation

Size: 10-16 ab.

Vent driver assembly operates the dryer vent door to manage airflow during operation. Replacing a faulty driver restores proper vent door movement, improving exhaust flow and helping prevent backdrafts. What it does:

• Moves and positions the vent/duct door so exhaust can exit when the appliance runs
• Retracts/closes the vent door when the appliance stops to limit backdrafts
• Common symptoms: vent door won't open or close, reduced exhaust airflow, or visible vent door sticking
• Interfaces with the vent door linkage and the appliance wiring harness to receive control signals

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Basic hand tools are typically required; support the vent door assembly during removal/installation
• Handle wiring connectors and plastic components carefully to avoid damage
• Follow the appliance's service manual or OEM instructions for exact steps and torque/spec guidance

This hex-washer-head screw secures appliance components and panels. The correct 10-16 thread, 1-inch length fastener restores a tight, factory fit when an original screw is missing, stripped, or corroded.

• Fastens brackets, shields, trim, or panels to the appliance chassis
• Helps resolve rattling, gaps, or loose parts caused by a missing/damaged screw
• 10-16 thread with 1-inch length matches factory hardware for specified locations
• Hex-washer head provides solid tool engagement and distributes load to protect surfaces

• Disconnect power before servicing; if working on a gas appliance, also shut off the gas supply
• Support the part being secured and align holes before tightening
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Replace any additional missing screws in the same area for uniform support

This clamp secures a hose or small tubing connection on compatible GE laundry appliances to help prevent leaks and keep the connection stable during operation. Durable metal construction resists vibration and wear. What it does:

• Holds a hose or tube firmly to a fitting to reduce leaks and loss of water or airflow
• Stops hose slippage caused by vibration or pressure changes
• Helps restore a tight connection after hose replacement or service
• Simple, low-profile design for use in confined appliance spaces

• Disconnect power and shut off water supply before servicing
• Drain hoses and remove remaining water to avoid spills
• Use the proper screwdriver or nut driver to tighten; do not over-tighten
• Inspect the hose and fitting for wear and replace if damaged before reinstalling the clamp

A small replacement clamp used to secure hoses and small assemblies to prevent leaks or disconnection. Fits the original mounting point and restores a tight seal where the worn clamp no longer holds reliably. What it does:

• Secures a hose or tubing connection to keep water or air from leaking
• Restores proper tension where the original clamp has loosened or corroded
• Helps stop intermittent leaks and prevents hoses from slipping off fittings
• Works in confined appliance areas where a compact clamp is required

• Turn off power and water to the appliance before starting any repair
• Use appropriate hand tools; avoid over-tightening to prevent hose damage
• Dispose of the old clamp and any corroded hardware; inspect surrounding fittings for wear

Includes 12 screws.

This rubber grommet provides a protective seal where hoses, wires or components pass through openings, helping prevent chafing and moisture intrusion. Use it to restore a tight fit and reduce wear at the penetration point. What it does:

• Seals and cushions openings to help prevent water leaks and air gaps.
• Protects wiring and hoses from rubbing on sharp metal edges that can cause wear or shorts.
• Reduces vibration and rattling by holding parts securely in place.
• Common symptoms of failure: visible cracking, missing or torn grommet, water dripping near the opening, or rubbing noises.

• Disconnect power to the appliance and turn off water supply before beginning any repair.
• Remove the access panel or boot as needed to reach the opening; press the grommet into the hole until fully seated.
• Inspect surrounding seals, hoses and wiring; replace any damaged components to prevent repeat issues.

This left-hand arm hinge assembly replaces a worn or damaged door hinge to restore proper door alignment and smooth opening and closing. Designed as the left-side support arm for the appliance door. What it does:

• Supports the left side of the door and secures the door to the cabinet during operation
• Guides smooth door movement and helps prevent sagging or uneven closing
• Stops rubbing, binding, or intermittent contact that can cause noise or poor seal
• Restores proper door fit to maintain normal operation and safety

• Disconnect power to the appliance before starting any repair
• Support the door while removing and installing the hinge to prevent dropping
• Use basic hand tools; verify hinge orientation and alignment before tightening
• Retain or replace mounting hardware if damaged; do not overtighten fasteners

This replacement basket lid is the top cover for the laundry basket assembly, restoring a secure, finished opening so laundry stays contained and the appliance looks and operates as intended. What it does:

• Replaces a cracked, warped, or missing basket lid to restore the basket opening
• Helps keep clothes contained during loading and unloading
• Reduces movement and rubbing that can cause fabric snags or noise
• Restores proper fit and appearance of the basket area

• Disconnect power to the appliance before starting any repair
• Basic hand tools may be required; for disassembly steps
• Handle edges carefully to avoid scratching the finish during install
• If clips or fasteners are damaged, replace them to ensure a secure fit

Size: 8-18 B 1HW 1/2 S N

This rubber grommet cushions and seals appliance components to reduce vibration and prevent wear. It replaces a worn or torn grommet to restore proper fit and quiet operation. What it does:

• Cushions metal-to-metal contact to reduce noise and vibration.
• Helps secure hoses, wiring, or panels where mounted through a hole.
• Prevents chafing and protects components from abrasion.
• Common symptom: rattling, rubbing sounds, or visible rubber deterioration.

• Turn off power to the appliance before starting any repair.
• Remove necessary panels or components to access the damaged grommet; note fastener locations for reassembly.
• Press or push the grommet into the mounting hole until fully seated; some installations may require a flat tool to ease placement.
• If grommet secures wiring or hoses, verify routing and clearance before restoring power.

This inlet transition is a molded connector that fits between the appliance cabinet and the inlet opening to guide incoming air and help maintain a sealed airflow path. It restores proper fit and reduces air leakage where the inlet meets the cabinet. What it does:

• Provides a finished, secure connection at the appliance inlet to direct airflow into the unit
• Helps reduce air leaks that can reduce drying/heating performance or cause airflow imbalance
• Replaces worn, cracked or broken inlet trim that can rattle or vibrate during operation
• Restores correct clearance and sealing where the inlet joins the cabinet

• One inlet transition piece

• Basic hand tools typically required; access the inlet area by removing the back panel or service panel as applicable
• Handle carefully to avoid bending or damaging adjacent trim and mounting tabs
• Disconnect power (and gas if applicable) before beginning service; follow all safety precautions in the appliance manual
• If mounting hardware is missing or damaged, replace with OEM-specified fasteners for secure fit