Pgs920sef Parts

This oven felt seal fits around the door perimeter to cushion the door and help reduce heat loss. It restores the intended door clearance and soft contact between the oven door and frame for safer, quieter operation. What it does:

• Cushions the oven door edge to prevent metal-on-metal contact and reduce rattling
• Helps limit heat and smoke from escaping the oven cavity when the door closes
• Restores proper door clearance to prevent scraping or uneven sealing
• Commonly replaced when felt is worn, compressed, torn, or missing

• One oven felt seal as shown

• High-level replacement; remove the oven door or open hinge per your service manual before replacing the seal
• Work with the oven powered off and fully cooled; disconnect power for safety
• Press the felt into the channel or adhesive area; ensure even fit around the full perimeter

Right hand side

A receiver hinge that secures and supports an oven door hinge pin to keep the door aligned and operating smoothly. Replaces a worn or broken receiver to restore proper door fit and movement. What it does

• Accepts and retains the oven door hinge pin so the door opens and closes correctly.
• Supports door weight to prevent sagging or uneven alignment.
• Helps the door latch and seal properly for safe, consistent operation.
• Commonly replaced when the door drops, rubs, or will not stay closed.

• One receiver hinge

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove the oven door or access panel per the service manual for safer installation.
• Use basic hand tools; check hinge pins and mating hardware for wear and replace if needed.

Door hinge replacement that restores proper door alignment and smooth opening and closing for compatible appliances. Installs in place of a worn or damaged hinge to reduce door sag, improve sealing, and stop binding. What it does:

• Provides the pivot point that allows the door to open and close smoothly.
• Keeps the door aligned to maintain an even seal and prevent gaps that cause temperature loss.
• Replaces a bent, worn, or damaged hinge that can cause door sag, rubbing, or binding.
• Helps reduce noise or rough movement when opening or closing the door.

• Disconnect power (unplug or shut off the circuit) before beginning any repair.
• Support the door during removal and installation to prevent it from dropping or becoming damaged.
• Use appropriate hand tools and follow the appliance manufacturer's instructions; tighten fasteners securely but avoid overtightening.

The upper manifold panel is an OEM part for GE ranges. It is responsible for housing and protecting the control buttons and knobs of the range. It is designed to withstand daily use and resist damage from heat, moisture, and other external factors.

A bad upper manifold panel can result in issues such as unresponsive buttons, malfunctioning knobs, or a worn-out appearance. Causes of a bad panel can include wear and tear over time, accidental spills, or damage due to impact.

Symptoms of a bad upper manifold panel include:

• Unresponsive or sticky buttons
• Loose or broken knobs
• Faded or worn-out labeling on the panel
• Difficulty in adjusting or setting cooking functions

Replace your worn-out or damaged upper manifold panel with this genuine OEM GE part to restore your range. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This oven light gasket fits between the glass lens and the oven liner. It restores a proper seal around the light opening to help keep grease and moisture out of the light cavity and hold the lens securely in place. What it does:

• Seals the joint between the oven light lens and the cavity wall
• Helps prevent grease and moisture from entering the light assembly
• Keeps the lens snug to reduce looseness or rattling
• Replace if the gasket is cracked, flattened, brittle, missing, or if moisture/grease is visible around the lens

• One oven light lens gasket

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the light lens/retainer as your model requires (unscrew lens or release clips)
• Note gasket orientation and clean the mating surfaces
• Seat the new gasket evenly and reinstall the lens; do not overtighten the glass

This 1/4-20 screw secures panels, brackets, and other assemblies in your appliance. It restores a tight, reliable hold when an original fastener is missing, stripped, or corroded.

• Fastens components that require a 1/4-20 threaded screw
• Helps keep panels and assemblies aligned and rattle-free
• Direct replacement for worn, rusted, or lost hardware
• Common symptoms: loose or vibrating parts, misaligned brackets, missing fastener

• Disconnect power; turn off gas supply before servicing
• Allow the appliance to cool; wear gloves and eye protection
• Start threads by hand to avoid cross-threading; use the correct driver/tool
• Tighten snugly—do not overtighten to prevent stripping or damage

The Burner Valve Assembly 270 is an OEM part for GE gas ranges. It controls gas flow to individual burners to deliver precise heating levels.  

Causes of a bad burner valve assembly include worn rubber diaphragms, debris inside valve channels, or damage from repeated heating cycles.

Symptoms are:

• Uneven cooking temperatures across burners
• Inability to ignite or adjust certain burners  
• Fluctuations in flame height/cooking output

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models.

This small replacement bumper cushions and protects the appliance frame/trim where panels meet, helping reduce vibration, chipping and rattles for a cleaner, quieter fit. Ideal when the original bumper is worn, cracked or missing. What it does:

• Cushions contact between the frame/trim and adjacent panels to reduce noise and prevent damage
• Helps maintain proper panel alignment and sealing where the trim meets the cabinet
• Reduces rattling or vibration caused by loose or degraded trim pads
• Restores protective spacing that prevents chips or scratches to finished surfaces

• One frame front bumper

• Disconnect power to the appliance before starting work and follow all safety precautions
• Usually installs by pressing into a slot or onto a mounting surface after removing the trim piece; some trim removal may be required
• Inspect mating surfaces for damage or debris and clean before installing the new bumper
• Replace with the exact part number only; do not force or modify the bumper to fit

The Spark Ignition Switch and Harness is an OEM part for GE ovens and ranges. This switch and harness work together to safely ignite the gas burners by providing power from the control unit to the burners.

Causes of a bad switch or harness include wear and tear over time from repeated use or aging components. It could also be damaged from liquid spills or cleaning chemicals getting inside the unit.

Symptoms of a bad switch or harness include:

• Gas burners not lighting properly or at all
• Irregular or no ignition of the burners
• Safety issues with gas leaks if the switch fails to ground properly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Burner Valve Assembly 3R 310 is an OEM part for GE gas ranges. It controls gas flow to individual burners to deliver precise heating levels.  

Causes of a bad burner valve assembly include worn rubber diaphragms, debris inside valve channels, or damage from repeated heating cycles.

Symptoms are:

• Uneven cooking temperatures across burners
• Inability to ignite or adjust certain burners  
• Fluctuations in flame height/cooking output

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models.