Pgss5pjxss Parts

This fastener secures appliance components where a #8-18 AB hex-washer-head screw is specified. At 1/2 inch long, it restores a tight, reliable hold when an original screw is missing, damaged, or stripped.

• Secures brackets, panels, and covers where this size/thread is specified
• Replaces missing, stripped, or corroded screws
• Helps reduce vibration or rattling caused by loose fasteners
• Correct #8-18 AB thread and 1/2-in length for a precise fit

• Disconnect power before servicing; shut off water supply if working near water connections
• Compare to the original to confirm length and thread match
• Start threads by hand to prevent cross-threading; use the correct driver for the head type
• Tighten snugly; do not overtighten into plastic or thin sheet metal

• Thread: #8-18 (Type AB)
• Head: Hex-washer
• Length: 1/2 in

This stand off is a small mounting spacer that secures and spaces internal components, restoring proper alignment and reducing panel movement or vibration for quieter, more reliable operation. What it does:

• Provides a solid mounting point to hold panels, brackets or wiring harnesses in place.
• Replaces broken, cracked or missing standoffs that allow components to shift or rub.
• Helps stop rattling, buzzing or misalignment caused by loose mounting points.
• Keeps proper clearance between parts to prevent wear or chafing over time.

• Disconnect power to the appliance before starting any repair.
• Remove the affected panel or access cover to reach the damaged standoff.
• Replace the old standoff with the new part; retain and reuse any existing screws or fasteners unless damaged.
• Hand-tighten mounting hardware and test the appliance; avoid overtightening plastic standoffs.

This OEM fastener secures interior components and trim on compatible appliances to restore proper fit and reduce movement. It's a direct-replacement hardware piece used where the original mounting screw or retainer is lost or worn. What it does

• Secures panels, trim pieces, brackets or small assemblies to the appliance frame
• Restores firm attachment to reduce rattles, gaps or misalignment
• Replaces missing or stripped hardware that prevents proper part installation
• Helps maintain proper operation by keeping service parts seated and stable

• Disconnect power or unplug the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Hand-start the fastener, then tighten snugly—do not over-torque
• Replace any additional damaged fasteners with the same OEM part for best fit

This 8-18 x 9/16 screw is a short sheet-metal fastener used to secure panels, trim and small components on appliances. It replaces missing or stripped screws to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance panels, brackets and trim to prevent movement and rattling
• Holds small components in correct alignment for reliable operation
• Replaces lost, worn or stripped screws that cause gaps or loose fittings
• Common symptom link: fixes rattling panels, loose trim, or parts that shift during use

• One 8-18 x 9/16 screw

• Use the correct 8-18 driver bit and hand or low-torque power driver to avoid stripping
• Do not overtighten; snug until secure to prevent thread damage or panel deformation
• Turn power off/unplug appliance when installing near electrical components
• Keep extra screws on hand—hardware often comes in single quantities

Size: 8-32 t. Includes 12 screws.

This spring closure is the OEM-style replacement that helps a door or panel return to a closed position smoothly and reduces slack or slamming for improved alignment and operation. It fits the original mounting points and restores the intended closing action. What it does:

• Provides the tension needed to pull a door/panel closed and hold it in place
• Restores consistent closing action when the original spring is worn or broken
• Helps reduce noisy slamming and prevents partial-open gaps that affect seal and alignment
• Works with the door/panel linkage to improve day-to-day usability

• One spring closure

• Turn off power to the appliance or unplug it before starting any repair
• Verify correct orientation and routing before fastening; spring tension can cause sudden movement
• Use appropriate hand tools and eye protection; if the original mounting clips are damaged, replace them as well

This replacement filter bypass adapter lets a refrigerator water line run without a filter cartridge installed, providing a secure connection so the dispenser and ice maker can continue to get water when a filter is removed. What it does:

• Replaces the filter cartridge with a sealed bypass so water flows through the housing without a filter element
• Restores normal dispenser and ice maker flow after removing or bypassing a cartridge
• Prevents leaks at the filter housing when a cartridge is not installed
• Useful when using an alternate filtration system or awaiting a replacement cartridge

• Shut off the water supply and run the dispenser until flow stops before starting
• Remove the old filter or cartridge per the owner's manual, then install the bypass in the same orientation
• Inspect the housing O-ring and replace if damaged to ensure a tight seal

This condenser fan shroud directs cooling airflow across the condenser and keeps the condenser fan and motor securely positioned for reliable cooling performance. It helps maintain proper condenser airflow and protects fan components from contact. What it does:

• Guides airflow from the condenser fan to improve heat dissipation
• Holds the condenser fan motor and blade in the correct position
• Reduces the risk of fan-to-coil contact and related noise or damage
• Can help address symptoms like noisy fan operation, increased run time, or reduced cooling when damaged or missing

• Disconnect power to the appliance before beginning any work
• Handle carefully — edges and nearby sheet metal can be sharp
• Basic hand tools are typically required; follow OEM instructions for removal/installation

This 10-32 x 1/2 machine screw secures appliance components where a standard 10-32 fastener is required. It restores proper mounting and reduces vibration or loose panels for reliable, quiet operation. What it does:

• Secures panels, brackets, or components that use a 10-32 threaded hole
• Prevents rattling, misalignment, and intermittent contact caused by loose fasteners
• Maintains electrical or mechanical connections when used as the OEM-specified screw
• Helps restore fit and finish after repair or disassembly

• Use the correct 10-32 driver (Phillips or slotted depending on head) and hand-start the screw to avoid cross-threading
• Tighten until snug; avoid over-tightening to prevent stripping threads or cracking plastic parts
• Replace only with the same size and thread spec to ensure proper fit
• Disconnect power if working near energized components or wiring

A short 8-32 x 3/8 hex washer head screw used to secure small appliance panels and components. Simple replacement for stripped or missing fasteners to restore proper fit and prevent rattles or loose parts. What it does:

• Secures panels, brackets, and small assemblies in place
• Helps eliminate vibration-related noise from loose parts
• Replaces missing, damaged, or corroded screws to restore proper alignment
• Fits standard 8-32 threaded holes requiring a 3/8" length screw

• One 8-32 x 3/8 hex washer head screw

• Use the correct 8-32 driver to avoid stripping the head
• Tighten snugly but avoid over-torquing to prevent thread damage
• Disconnect power and follow appliance safety procedures before accessing internal components
• Replace only like-for-like fasteners in load-bearing or safety-critical locations

This is a 10-32 machine-thread screw used to secure appliance panels, trim, and components. It replaces missing or damaged fasteners so parts fit tightly and operate without rattles or misalignment. What it does:

• Fastens panels, brackets, or assemblies that use a 10-32 machine screw
• Restores secure mounting where a stripped, missing, or corroded screw causes looseness
• Helps eliminate vibration noise or gaps caused by loose hardware
• Matches OEM thread size and length for correct fit in designated mounting holes

• One 10-32 x 5/16 machine screw

• Disconnect power and remove power source or batteries before servicing appliances
• Use the correct screwdriver or nut driver to avoid stripping the head
• Thread carefully; do not force or overtighten to prevent thread damage
• Replace any damaged mating hardware or clipped inserts for a secure repair

This is a 1/4-10 x 3/4 hex washer head screw that secures panels and components on compatible appliances, restoring proper fit and stability. Use when mounting hardware is loose, missing, or a screw is stripped or broken. What it does:

• Fastens panels, brackets, and assemblies with a hex washer head for a secure hold
• Replaces missing or damaged screws that cause rattling or loose parts
• Restores proper alignment and tension where the original screw was used

• Use the correct 1/4-10 driver or socket to avoid cam-out
• Tighten securely but avoid over-tightening to prevent thread damage
• Replace any stripped mating fastener for best results
• Disconnect power before working on electrical components or near wiring