Prg366gh/08 Parts

This replacement tube routes water between internal components to maintain a sealed, reliable flow path. Swapping a cracked or hardened tube helps stop leaks and restore proper circulation and overall appliance performance.

• Carries water between internal components and maintains proper flow
• Helps keep connections watertight to prevent drips and pooling
• Replace if you see leaks, visible cracks, kinks, or a loose fit
• Restricted flow from a worn tube can contribute to reduced cleaning/performance

• Disconnect power and turn off the water supply before servicing; allow the unit to cool
• Remove access panels and keep towels handy for residual water
• Note the original routing and connection depth; transfer any fittings or clamps from the old tube if applicable
• Push the tube fully onto fittings and secure; run a test cycle and check carefully for leaks

This facia panel is the exterior trim that covers and protects the appliance's front control area, restoring a finished appearance and protecting internal controls from everyday wear. Ideal when the existing panel is cracked, scratched, or cosmetically worn. What it does:

• Covers the control board and user interface, providing a finished front surface
• Protects buttons, touchpads, and switches from accidental damage and debris
• Restores the appliance's appearance after chips, scratches, or faded finish
• Helps keep moisture and food soils away from internal control components

• One facia panel (trim piece) as shown

• Disconnect power to the appliance before starting any repair
• Typical installation requires removal of outer trim or inner door panel; keep all screws and clips for reassembly
• Handle with care to avoid scratching the new panel; align tabs and clips before tightening fasteners

This hinge plate is a replacement door hinge support that helps secure and align the appliance door for smooth opening and closing. Restores proper door alignment and support when the original hinge plate is worn or damaged. What it does:

• Provides a mounting surface for the door hinge to keep the door aligned
• Helps prevent door sagging, misalignment, and uneven closing
• Restores stable door movement and reduces stress on hinge assemblies
• Works with the existing hinge hardware to maintain proper door operation

• Hinge plate

• Disconnect power to the appliance before attempting any repairs and remove any water supply if applicable
• Handle the door carefully during removal/installation to avoid dropping or damaging the door or trim
• Use basic hand tools; support the door while swapping hinge components to prevent injury or damage

This compression nut secures 3/8 in. refrigeration or water tubing to a matching compression fitting, creating a tight mechanical seal for supply lines. It's a simple, serviceable fastener used on valves and pipe connections. What it does:

• Threads onto a compression fitting to hold ferrule and tubing in place
• Helps create a leak-resistant joint on 3/8 in. tubing connections
• Commonly used on water supply, ice maker, or refrigeration line fittings
• Replaces a worn or damaged nut that causes loose or leaking connections

• Turn off water or power to the appliance and relieve system pressure before servicing
• Hand-start threads to avoid cross-threading; tighten snugly with appropriate wrenches
• Inspect ferrule and tubing; replace ferrule or cut tubing square if reusing connection
• If you see persistent leaks after tightening, stop and check components.

This compression sleeve seals 3/8-inch refrigeration or water tubing where a compression fitting is used, restoring a tight, drip-free connection. It's a simple replacement to stop leaks and ensure a secure joint. What it does:

• Acts as the ferrule inside a compression fitting to compress against tubing and create a seal
• Restores a worn or flattened sleeve that causes leaks at nuts or fittings
• Used with a matching compression nut and fitting to secure 3/8" tubing
• Commonly replaced when connections leak, weep, or fail to hold pressure

• One compression sleeve sized for 3/8 in. tube

• Turn off and depressurize the system (water or refrigeration) before removing fittings
• Cut tubing square and deburr before installing the sleeve for best seal
• Slide the nut then the sleeve onto the tube, seat against the fitting, and tighten to manufacturer torque
• Inspect the joint for leaks after pressurizing and retighten if needed; replace sleeve if damaged during installation

This replacement cover is an exterior access panel that protects internal components and finishes the appliance for a clean look. It restores a sealed barrier over controls and wiring to help keep parts secure and reduce drafts. What it does:

• Covers and protects internal wiring, terminals and small components from debris and accidental contact
• Restores finished appearance where a damaged or missing panel left an opening
• Reduces rattling or vibration caused by loose or broken panels
• Helps prevent moisture and foreign objects from entering the service area

• One cover

• Disconnect power to the appliance before starting any work
• Installation may require removing screws or unclipping snap-in fasteners; keep hardware if reusing
• Handle edges carefully—use gloves to avoid cuts on sheet-metal edges

This replacement screw fastens appliance components to restore secure assembly and stable operation. It's a direct-fit fastener used where the original screw has stripped, corroded, or been lost. What it does:

• Secures panels, brackets, or small assemblies to prevent vibration and misalignment
• Restores proper fit where a damaged or missing screw causes rattling or loose parts
• Provides the correct fastening point for unchanged OEM mounting locations
• Works as a like-for-like replacement when the original screw is worn or missing

• Screw

• Turn off and unplug the appliance before beginning any repair
• Use the matched screwdriver or driver bit to avoid stripping the head
• Replace with the same thread engagement depth; do not force or overtighten
• Repair with the appropriate method before installing

This heat shield is a stamped metal panel that redirects and blocks excess heat inside the oven cavity to protect wiring, insulation, and nearby components. It restores proper heat management and helps prevent heat-related damage. What it does:

• Shields adjacent parts from direct flame or intense oven heat
• Prevents heat transfer to wiring, insulation, and control components
• Reduces risk of warped or discolored cabinet panels near the oven
• Useful when the original shield is dented, rusted, or missing

• One heat shield panel

• Disconnect power (and gas if applicable) before servicing
• Allow the appliance to fully cool prior to removal/installation
• Use proper fasteners and align to existing mounting points; retain any original screws
• Beware of sharp metal edges and wear gloves