Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Grey thumb screw secures attachments on stand mixers. Replacement needed when original screw cracks, breaks, or threads strip. Installs easily by hand.
Replaced it with ordered part. Read more
Replacement spring for stand mixer beater shaft assembly. Secures to lift rod with nut and washer. Install if original spring is missing, broken, or lost.
Replaced the part. Read more
Replacement mounting screw for stand mixer panels, brackets, and trim. Secures internal components to keep parts aligned. Replace if missing, stripped, or rusted.
Fix mixer parts that shift or make noise with this retaining ring. Snaps into groove to secure components on shaft. Takes under 20 minutes to install.
I watched the video demonstration on the AppliancePartsPros.com website. It was easy to follow, and in less than 20 minutes my daughter's KitchenAide Mixer was as good as new. Read more
Rubber foot for stand mixer base. Replaces worn, cracked, or missing feet. Stabilizes mixer, reduces vibration, and protects countertops.
Super simple fix. The board plug in are in a little different location but were easily identified. Read more
Replacement 8-32 x 5/8 mounting screw for securing internal panels, brackets, and components in stand mixers. Restores tight fit if original is missing or stripped.
I purchased a replacement assembly from Appliancepartspluspro.com Upon inspection of new part I noticed there were only 6 terminals for the 8 wires I needed to connect. After much investigation by their tech support person Ali, it became apparent that my old part was discontinued and no longer available. The new part was the correct replacement but now I had to figure out what to do with the 2 extra wires. I labeled all of the wires and the terminals on the the old part. After moving wires, one... Read more
Pouring shield attaches to 5-6 quart lift bowl stand mixer to prevent ingredients from flying out while mixing. Replace if lost or damaged. Verify fit.
Bought a new one. Read more
Fix a mixing bowl that won't lock in place or keeps sliding during use. This retaining pin secures the bowl clip to keep your bowl firmly seated.
If your mixer bowl won't stay in place or wobbles during mixing, this retainer clip secures it properly. Simple DIY fix takes just minutes to install.
Screwed in the new clip with the new screw. Unfortunately it was too tight for the bowl so I loosened the screw and the bowl attached just fine. Read more
Mounting screw secures internal brackets and panels in mixers. Replace if missing, stripped, or damaged to prevent loose components and rattling.
If your mixer's bowl lift handle is cracked or missing, this rotating handle restores convenient bowl access. Simple installation—no tools needed.
Our Kitchen Aid mixer was shipped without a handle on the arm that raises and lowers the bowl. Apparently it was a cost savings measure on some models. Kitchen Aid support was no help. I searched Appliance Parts Pro, found the part, ordered it and was able to install with only a rubber mallet. Price and shipping was fair. Read more
Fix a mixer that won't engage or slips during operation. This cam restores proper mechanical linkage timing. Straightforward DIY replacement part.
I put in a new one from Appliancepartspros.com Read more
Factory replacement screw for stand mixers. Secures panels, brackets, and internal components. Replace lost, stripped, or corroded hardware for proper fit.
Secure panels and components with this 6-32 machine screw. Replaces stripped, missing, or damaged fastening screws to restore proper fit and stability.
Replace your chipped or discolored mixer paddle to restore smooth, even mixing. This coated flat beater fits select KitchenAid models. Easy DIY fix.
Replaced beater blade and hope it doesn't happen again. tried to purchase replacement beater blade in BB&B store.. Their cost $42.98. Your cost $14.99. Obviously, I will remain with your website. I have used it before and will use it again. Read more
If your stand mixer won't turn or makes grinding noises, the planetary gear assembly likely failed. Transfers motor power to the beater shaft.
I ordered a new one from ApplincePartsPros.com They are always ready to help with their videos and help with getting all the right parts. My wife thinks I can fix anything if she only knew were I get my info Thank all the fine staff at AppliancePartsPros Mark Read more