Ps950fsss Parts

This glass control and board assembly replaces the cooktop's front touch/control panel and the electronic board behind it, restoring user input and control of heating functions. Fits single-surface electric/induction ranges using a glass control assembly. What it does:

• Replaces the glass touch/control panel and the associated control electronics that register user commands.
• Restores responsive touch keys/buttons and display functions when worn or unresponsive.
• Resolves symptoms such as unresponsive controls, missing display LEDs, intermittent control behavior, or failure to start heating cycles.
• Interfaces with range power and element control circuits to send user commands to the cooktop.

• One glass control panel with attached control board assembly.

• Disconnect power at the breaker before starting; serious shock hazard if power is not removed.
• Handle the glass panel carefully to avoid cracking; use proper lifting and support during removal/installation.
• Note connector locations and mounting hardware; mark or photograph wiring before disconnecting.

This is a truss-head screw used to fasten appliance panels and trim securely. It provides a low-profile, wide bearing surface to hold components in place and resist pull-through. What it does:

• Fastens trim, access panels, brackets, and lightweight components
• Wide truss head spreads load to prevent damage to thin sheet metal
• Replaces missing or stripped screws that cause loose panels or rattling
• Maintains proper alignment of cosmetic and service panels

• One truss-head screw (8-32 x 0.343 in)

• Use the correct #2 Phillips driver; a magnetic bit helps hold the screw
• Tighten snugly but avoid overtightening to prevent thread or panel damage
• Disconnect power before removing or working near electrical components
• If threads are damaged, replace with the exact part rather than reusing with thread repair

This daughter relay board connects to the main control and switches specific appliance functions, restoring power delivery to heating or motor circuits so the unit runs only the functions it needs. Fits as a direct replacement relay daughter board. What it does

• Switches power to individual appliance circuits under control commands from the main board.
• Helps enable heating elements, motors or other controlled loads when relays close.
• Commonly linked to symptoms such as elements or motors that don't energize, intermittent operation, or control errors.
• Works as a replacement component when the existing relay board is burned, charred, or fails to activate circuits.

• One daughter relay board

• Disconnect power before accessing or servicing the appliance to avoid shock or damage.
• Handle the board carefully to avoid static discharge; use proper ESD precautions if available.
• Verify connector orientation and seating; do not force pins—match keyed connectors.

8-18 AB IHW 5/8 S

This vent tube directs heated air and moisture from the appliance to its exhaust path, maintaining proper airflow around internal components. Replace a cracked, warped, or missing tube to restore safe ventilation and help prevent heat and condensation buildup. What it does:

• Channels hot air and steam from the cavity to the outlet
• Helps prevent heat accumulation around controls and adjacent surfaces
• Reduces moisture/condensation at the vent outlet
• Common symptoms: excessive warmth near the console, persistent odors/steam, visible damage, or rattling from a loose/broken tube

• 1 vent tube

• Disconnect power; shut off gas. Allow the appliance to cool completely before servicing.
• Access and attachment points vary by model; refer to your service manual or diagram for location.
• Note the tube's orientation and routing; transfer any brackets or seals from the old part if present.
• Reuse existing screws/clamps and ensure the vent path is clear after installation.

This electrical jumper links two terminals within the appliance's wiring to restore proper continuity for the affected circuit. Replace a burnt, damaged, or missing jumper to bring the related function back to reliable operation.

• Bridges terminals to complete or modify an electrical circuit as designed by the manufacturer
• Helps address symptoms like a specific feature not working, intermittent operation, or no power to a component
• Replace if the original shows heat damage, broken leads, or loose connections
• Direct replacement for the original jumper used in the wiring harness

• Disconnect power at the breaker or unplug the appliance before servicing
• Use your model's wiring diagram to locate the correct jumper
• Label/photograph wire positions and transfer one connection at a time
• Ensure connectors are fully seated; do not alter the factory wiring configuration

This thermal cutoff (runaway) is a temperature-safety device that stops the dryer's heating circuit if temperatures exceed safe limits, helping prevent overheating and potential fire hazards. Replaces a failed or tripped runaway TCO in dryer heating assemblies. What it does:

• Opens the heating circuit if the dryer temperature climbs above safe thresholds to stop further heating.
• Prevents uncontrolled heating when other thermostats or controls fail.
• Common symptom: dryer overheats or element stays energized; may also result in no heat if the cutoff is open.
• Works with the dryer's existing thermostats and heating element assembly as a safety interlock.

• One thermal cutoff (runaway) device.

• Disconnect all power before accessing the dryer heating assembly.
• Locate and replace the TCO on or near the heater housing; keep wiring orientation the same.
• Do not bypass or defeat safety devices; After replacement, inspect other thermostats, fuses, and the heating element for related faults.

This module indicator light is the small lamp that illuminates a range or oven control module so you can see status and settings. It replaces a worn or burned-out control lamp to restore front-panel visibility and feedback. What it does:

• Lights the control module so panel indicators and displays are visible
• Signals control status when the oven or range is powered and operating
• Commonly replaced when the panel stays dark or individual indicator fails
• Helps restore clear visual feedback from touchpads and selector controls

• One module indicator light

• Disconnect power to the appliance before inspecting or replacing the lamp
• Access may require removing the control panel or console; handle modules and wiring gently
• Verify proper seating and secure connections before restoring power
• Test the control board and wiring for faults

This right-side hinge assembly secures and guides the appliance door for consistent opening and closing, restoring proper alignment and sealing. It's a direct-fit replacement when the door feels loose, binds, or won't stay aligned. What it does:

• Supports the door on the right side and maintains correct pivoting motion
• Restores proper door alignment to improve closing and sealing
• Helps eliminate sagging, binding, or uneven gaps during operation
• Works with existing hinge pins and mounts where applicable

• Replace both hinges if the left-side hinge shows similar wear; balance is recommended for long-term alignment
• Disconnect power and remove any panels or door components per manufacturer instructions before starting
• Use proper tools and keep fasteners organized; tighten to OEM torque if specified

This chassis brace is a right-side cabinet support that stabilizes the appliance frame and helps keep panels aligned for reliable operation and a secure fit. It restores proper cabinet support after damage or wear. What it does:

• Provides structural support to the appliance cabinet on the right side
• Helps keep exterior panels and controls aligned to reduce vibration and rubbing
• Restores correct spacing for components mounted to the chassis
• Commonly replaced when bent, cracked or after collision damage

• One right-side chassis brace

• Designed for straightforward replacement; refer to your model's service manual for exact steps
• Disconnect power (and gas if applicable) before beginning any repair
• Use proper fasteners and torque per OEM instructions; avoid overtightening
• If cabinet damage is extensive, inspect surrounding components for additional repairs