Psb2201nss Parts

This turntable motor replaces the drive that spins the microwave glass tray so food heats evenly. The assembly includes the mounting gasket and restores smooth, consistent rotation when the original motor is seized, noisy, or stalls under load.

• Rotates the glass tray at a steady speed for even cooking and reheating
• Common symptoms of failure: tray not turning, intermittent rotation, loud humming or grinding
• Included gasket helps properly seal and cushion the motor mount

• Disconnect power before service; microwaves contain a high-voltage capacitor that can retain a charge
• Remove the glass tray and support ring; access the motor from the unit's underside
• Transfer/install the gasket in the same orientation; align the motor shaft with the coupler and secure with existing hardware
• Reconnect wiring and test turntable operation before reassembly

This NTC thermistor is a temperature sensor that feeds real-time temperature data to the control. Replacing a failing sensor helps restore accurate temperature regulation, reduce nuisance shutdowns, and improve consistent cycle timing and performance.

• Monitors temperature by changing resistance as heat rises or falls
• Sends a signal to the electronic control to manage heating and fan operation
• A failed sensor can cause inaccurate temperatures, short/long cycles, or sensor-related error messages
• May prevent certain cycles from starting

• Disconnect power and allow the appliance to cool completely before servicing
• Note connector orientation and wire routing; take a photo for reference
• Install the sensor in the original location/clip and route wires away from hot or moving parts
• Restore power and run a test cycle to proper temperature response

A temperature sensor assembly that monitors internal temperatures and sends readings to the appliance control so the unit can maintain proper heating or cooling. Replacing a failed sensor restores accurate temperature regulation and consistent performance. What it does

• Detects and reports temperature to the electronic control or thermostat
• Helps the appliance maintain set temperatures for consistent operation
• A faulty sensor can cause inaccurate temperature readings or uneven heating/cooling
• May trigger temperature-related error codes or put the unit into a diagnostic/fail-safe mode

• Disconnect power to the appliance before attempting any repair
• Handle the sensor and its wiring gently; avoid bending or damaging the sensing tip or connectors
• Reconnect wiring securely and confirm correct routing to prevent interference with moving parts

This micro switch is a small electromechanical door/control switch that restores reliable on/off signaling for your appliance. Replacing a failed switch helps restore normal operation and safety interlocks. What it does:

• Opens or closes an electrical circuit when actuated, enabling controls or motors to run
• Commonly used in door and safety interlock applications to prevent operation when open
• Can stop intermittent power or control-response problems caused by a worn switch
• Helps resolve symptoms like appliance not starting, controls not responding, or cycling unexpectedly

• One micro switch

• Disconnect power (unplug appliance or flip the breaker) before servicing
• Observe sharp edges and wear protective gloves; remove access panels as needed
• Verify correct switch orientation and actuator engagement before reassembly
• Test continuity with a multimeter after installation to ensure proper operation

The Relay Board is an OEM part for GE microwave ovens. It functions as an electronic gatekeeper, controlling power levels and settings based on commands from the control panel. 

Installed internally, this relay board routes appropriate voltages to the magnetron, fan, and other vital microwave systems during operation. Its components switch power on and off as the programmed cooking cycle directs.

Causes of a faulty board can include liquid damage, overheating from heavy usage over time, or failures in relay components. 

Symptoms of issues include: 

• Inability to select power levels or adjust time  
• Magnetron failing to cycle on or off correctly
• Fan or other internal parts not functioning as intended
• Microwave making unusual noises or failing to heat food

Replacing with this genuine OEM GE part restores full functionality and precise cooking performance. Compatible models include some Hotpoint, RCA, and select Kenmore microwave products.
 

This heater sheath is the metal protective tube that surrounds and secures a dryer's heating element, helping protect the element from abrasion and keeping heating airflow directed for reliable drying performance. What it does:

• Protects the heating element from contact and physical damage during operation
• Helps maintain proper airflow around the element for consistent heat distribution
• Reduces risk of element grounding or shorting caused by contact with other parts
• Can address symptoms like sputtering or uneven heating, burning/metallic smells, or visible damage to the element area

• 1 heater sheath

• Power off and unplug the appliance before service to avoid shock or injury
• Inspect the heating element and mounting hardware while replacing the sheath; replace any damaged parts
• Handle the sheath and element carefully—sharp edges may be present; wear gloves and eye protection

This installation hardware kit provides the mounting fasteners and brackets needed to secure the appliance during installation for a stable, code-compliant fit. Use it to complete new installs or replace missing hardware. What it does:

• Provides the mounting fasteners and brackets used to secure the appliance to surrounding cabinetry or floor
• Prevents shifting, tilting or excessive vibration after installation
• Enables proper alignment and stable operation following service or replacement
• Restores missing or damaged installation hardware so the appliance installs correctly

• Follow the appliance installation instructions and local codes; use only the fasteners supplied or specified by the manufacturer
• Disconnect power to the appliance before performing any installation or service that requires moving the unit
• Use appropriate tools and safety gear; some installations may require two people to safely position and secure the appliance
• If the appliance requires model-specific brackets or shims, confirm fit with the model's installation instructions before final installation

Replacement mounting bracket that secures internal panels or components to the appliance frame, restoring alignment and stability. Use this bracket to replace cracked, bent, or missing supports that cause vibration or loose parts. What it does:

• Supports and secures panels, trim, or internal assemblies to keep components properly aligned.
• Reduces rattling, sagging, or movement caused by a broken or missing bracket.
• Restores stable mounting after impact, wear, or stripped mounting points.
• Helps maintain proper fit and operation of adjacent parts by providing a solid attachment point.

• Disconnect power (and water/gas if applicable) before starting any repair.
• Basic hand tools required; remove adjacent panels or trim for access as needed.
• Retain original fasteners when possible; replace damaged clips or screws.

The Door Removal Tool is an OEM replacement part for GE microwave ovens. It is a specialized tool designed to assist in the safe and proper removal of the microwave door. This tool is essential for servicing, repairing, or replacing components within the microwave cavity, ensuring that the door can be securely detached and reattached without causing any damage.

Symptoms of needing the Door Removal Tool include:

• Requirement to access the interior components of the microwave for repairs or maintenance
• Difficulty in removing the microwave door using conventional methods
• Potential risk of damaging the door or other components without the proper tool

Causes for needing the Door Removal Tool can vary, but it is typically required when performing tasks such as replacing the magnetron, waveguide cover, or other internal parts that necessitate door removal for access.

This OEM replacement is also compatible with Hotpoint, RCA, and some Kenmore microwave models.

The Power Transformer is an OEM replacement part for GE microwaves. It is responsible for converting the incoming electrical voltage to the appropriate level required to power the microwave's various functions. It supplies power to the magnetron, which generates the microwaves used for cooking and heating.

Symptoms of a faulty transformer power unit include:

• No power or complete loss of power to the microwave
• Inconsistent or inadequate heating performance
• Unusual buzzing or humming noises during operation

A bad transformer power unit can occur due to electrical malfunctions, power surges, or component failure. If you experience issues such as no power to the microwave, inconsistent heating, or unusual noises coming from the unit, it may be time to replace the old or damaged transformer power unit with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This genuine oven rack restores interior cooking space and provides a stable, ventilated shelf for cookware. It replaces worn, bent, or missing racks so pans slide in and out smoothly for even cooking. What it does:

• Provides a sturdy support surface for cookware and bakeware
• Keeps food elevated for even air circulation and consistent baking
• Replaces damaged or warped racks that can cause uneven cooking or sticking
• Slides on existing oven rack guides for easy positioning

• Remove all oven shelves and allow the oven to cool before installing
• Slide the rack into the oven on the designated rack supports until fully seated
• No special tools required; check that the rack moves smoothly and sits level
• For safety, avoid leaning on racks or using them to support heavy loads beyond the oven's capacity

This circulation motor powers the circulating fan to move air inside the appliance, helping maintain even temperatures and support proper cooling or heating performance. It replaces a worn or failed motor to restore airflow. What it does:

• Spins the circulating fan or blower to move air through the appliance compartment
• Helps maintain consistent internal temperature and airflow for efficient operation
• Can address symptoms such as weak or no airflow, uneven cooling/heating, or unusual motor noise
• Works as the rotating drive component that transfers power to the fan assembly

• One circulation motor as shown

• Disconnect power before attempting any service to avoid electrical shock
• Verify orientation and mounting before removal; note wiring positions for reinstallation
• Use proper tools and follow manufacturer instructions; replace any worn grommets or fasteners as needed