Psh25pgw Parts

This spacer is a small mounting support used to maintain proper clearance and alignment between refrigerator panels, doors, or components. It helps reduce rubbing, vibration, and noise by restoring correct spacing and fit. What it does:

• Keeps panels, trim, or components spaced correctly to prevent metal-on-metal contact and wear
• Helps align doors and panels for a flush fit and smoother operation
• Reduces vibration and rattling caused by misaligned parts
• Used wherever a fixed clearance or gap is required during reassembly

• Disconnect power to the appliance before beginning any service that requires panel or component removal
• Inspect mating surfaces for damage or debris before installing the spacer; replace any damaged fasteners
• Install in the same orientation and location as the original spacer; do not overtighten mounting hardware

This 8-18 x 9/16 screw is a short sheet-metal fastener used to secure panels, trim and small components on appliances. It replaces missing or stripped screws to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance panels, brackets and trim to prevent movement and rattling
• Holds small components in correct alignment for reliable operation
• Replaces lost, worn or stripped screws that cause gaps or loose fittings
• Common symptom link: fixes rattling panels, loose trim, or parts that shift during use

• One 8-18 x 9/16 screw

• Use the correct 8-18 driver bit and hand or low-torque power driver to avoid stripping
• Do not overtighten; snug until secure to prevent thread damage or panel deformation
• Turn power off/unplug appliance when installing near electrical components
• Keep extra screws on hand—hardware often comes in single quantities

This damper assembly controls airflow between refrigerator compartments to help maintain even temperatures. Replaces a failed or stuck damper to restore proper air distribution and temperature balance. What it does

• Regulates cold air flow from the freezer to the fresh food section.
• Opens and closes in response to the refrigerator's temperature control / user settings.
• Commonly used when fridge temperature is too warm, too cold, or fluctuates between compartments.
• Helps reduce uneven cooling and prevents overworking the compressor when functioning correctly.

• One damper assembly.

• Disconnect power to the appliance before starting any repair.
• Handle the damper linkage and plastic parts carefully to avoid breakage.
• Verify electrical connectors are fully seated and routing does not block damper movement.

Size: 8-32 t. Includes 12 screws.

This condenser fan shroud directs cooling airflow across the condenser and keeps the condenser fan and motor securely positioned for reliable cooling performance. It helps maintain proper condenser airflow and protects fan components from contact. What it does:

• Guides airflow from the condenser fan to improve heat dissipation
• Holds the condenser fan motor and blade in the correct position
• Reduces the risk of fan-to-coil contact and related noise or damage
• Can help address symptoms like noisy fan operation, increased run time, or reduced cooling when damaged or missing

• Disconnect power to the appliance before beginning any work
• Handle carefully — edges and nearby sheet metal can be sharp
• Basic hand tools are typically required; follow OEM instructions for removal/installation

This shield trough assembly catches and channels defrost and condensation water away from the refrigerator cabinet to help prevent leaks and ice buildup. It's a direct-fit replacement that restores proper water drainage and containment. What it does

• Collects defrost and condensation runoff and directs it to the drain pan
• Helps prevent water pooling inside the cabinet and under the appliance
• Reduces ice or frost accumulation caused by redirected water
• Provides structural support for adjacent trim and evaporator covers where applicable

• Disconnect power to the appliance before beginning any repair.
• Remove relevant shelves, drawers, and trim panels to access the trough; keep fasteners organized.
• Handle gently to avoid bending or damaging mounting tabs and seal surfaces.

This is a replacement 10-32 x 1 machine screw used to fasten appliance components. It restores secure mounting of panels, brackets and hardware so parts stay aligned and vibration or rattling is reduced. What it does:

• Secures panels, brackets, housings and small components to the appliance frame
• Keeps control boards, motors or assemblies held firmly in place
• Prevents loose parts that can cause vibration, noise or intermittent connections
• Matches the OEM thread and length for proper fit when replacing a worn or missing screw

• Disconnect power before working inside the appliance
• Use the correct 10-32 driver or bit to avoid stripping the head
• Thread into the original hole and tighten snugly; avoid over-torquing
• Replace with the same size and thread type to ensure proper fit and safety

This water inlet valve assembly controls water flow to the dispenser and ice maker, restoring proper fill and dispensing when the valve is the source of the problem. Replaces a failed or leaking inlet valve to resume normal water delivery. What it does

• Opens and closes to let water into the ice maker and dispenser when signaled
• Stops water flow when closed to prevent continuous filling or flooding
• Commonly linked to no water dispensing, slow/weak fill, or intermittent filling of ice maker
• Helps stop leaks or drips when the internal valve seat is failing

• One water inlet valve assembly

• Disconnect power and shut off water before replacing to avoid electrical shock and flooding
• Verify water supply line is depressurized and dry before disconnecting fittings
• Tighten plumbing connections to the manufacturer torque recommendations; check for leaks after installation

This slide and bracket assembly restores smooth, supported movement for a refrigerator or freezer drawer. It replaces a worn or broken glide and helps the drawer open and close properly for reliable food access. What it does

• Provides the sliding track and mounting bracket that support a refrigerator/freezer drawer
• Restores smooth glide and proper alignment when original slide is bent, cracked or worn
• Helps eliminate drawers that stick, sag or fall out when opened
• Supports the drawer weight and guides it into place during use

• One slide and bracket assembly as shown

• Disconnect power to the appliance or remove food before starting to reduce risk of injury
• Typical install requires removing the drawer to access and replace the slide and bracket; retain screws or clips for reuse only if in good condition
• Inspect mating parts (drawer edges, cabinet track) for damage and replace if needed to ensure proper fit

This 10-32 x 1/2 machine screw secures appliance components where a standard 10-32 fastener is required. It restores proper mounting and reduces vibration or loose panels for reliable, quiet operation. What it does:

• Secures panels, brackets, or components that use a 10-32 threaded hole
• Prevents rattling, misalignment, and intermittent contact caused by loose fasteners
• Maintains electrical or mechanical connections when used as the OEM-specified screw
• Helps restore fit and finish after repair or disassembly

• Use the correct 10-32 driver (Phillips or slotted depending on head) and hand-start the screw to avoid cross-threading
• Tighten until snug; avoid over-tightening to prevent stripping threads or cracking plastic parts
• Replace only with the same size and thread spec to ensure proper fit
• Disconnect power if working near energized components or wiring

This pivot is the replacement pivot piece that supports and guides a refrigerator door or sliding drawer, restoring proper alignment for smooth opening and closing. Fits original equipment pivot points. What it does:

• Supports the weight of a door or drawer and keeps it aligned on its track
• Guides smooth opening and closing and prevents binding or sagging
• Restores proper contact and seal when a worn pivot causes misalignment
• Helps reduce noise from loose or worn pivot points

• Disconnect power to the appliance before beginning any repair
• Access may require removing interior panels, trim, or the drawer/door per model instructions
• Handle carefully to avoid scratching sealed surfaces; replace worn fasteners if needed
• If alignment issues persist after replacement, check related hinges, tracks, and mounting hardware

This flow meter is a dishwasher water flow sensor that measures incoming water to help the control manage cycle fill and wash performance. Replaces a failed or intermittent flow reading to restore proper water-level sensing. What it does:

• Senses and reports water flow to the dishwasher control so fill and wash cycles operate correctly
• Commonly linked to symptoms like improper filling, error codes related to water flow, or interrupted cycles
• Helps the control detect low or no flow conditions that can halt cycles for safety
• Works as the direct replacement component for the dishwasher's flow-sensing assembly

• One flow meter

• Disconnect power and water supply before servicing to avoid shock and flooding
• Handle the sensor and wiring gently; avoid kinking or stressing the harness during replacement
• Verify tight, leak-free connections to the inlet and control after installation

This module shelf secures the appliance's control or module assembly inside the freezer, keeping electronics stable and protected for reliable operation. It replaces a cracked or missing support and restores proper component positioning. What it does:

• Holds and supports the control/module assembly or related electronics inside the freezer compartment
• Prevents module shifting that can cause loose wiring or intermittent connections
• Helps maintain proper airflow around components by keeping parts in their intended position
• Reduces rattle and vibration noise from loose internal modules

• Disconnect power to the appliance before beginning any work to avoid electrical shock
• Access may require removing interior shelves, drawers, or a rear access panel—refer to your model's service instructions
• Handle electronic modules and connectors carefully; avoid pulling on wiring

This replacement painted #8-18 screw secures panels and components on select appliances, restoring proper fit and reducing vibration. Use it when original fasteners are missing, stripped, or corroded to help keep parts aligned and stable. What it does:

• Fastens trim, panels, brackets, and small components in appliance assemblies
• Replaces stripped, rusted, or missing #8-18 fasteners that cause loose parts
• Helps eliminate rattles and misalignment from loose or damaged screws
• Matches the painted finish for a cleaner, OEM-like appearance

• Use the correct driver bit and avoid over-torquing to prevent stripping
• Inspect mating threads and replace if damaged before installing
• Disconnect power to the appliance if working near electrical components; follow all safety precautions