Pss29nhpb Bb Parts

This fan and pre-wired harness assembly drives airflow to the Quick Chill/CustomCool drawer so foods and beverages chill faster and hold the set temperature. Replace a noisy, non-running, or intermittent fan to restore proper drawer cooling.

• Circulates cold air into the Quick Chill/CustomCool/deli drawer for targeted cooling
• Helps correct no-chill or slow-chill performance in the drawer
• Addresses symptoms like no airflow, intermittent operation, or grinding/buzzing noises from the drawer area
• Replaces a failed fan motor or damaged wiring harness in this assembly

• Disconnect power before servicing; remove the drawer and covers to access the assembly
• Note wire routing and connector locations; transfer any original mounting hardware as needed
• Seat connectors fully and route harness away from moving parts to avoid pinching
• Restore power and verify the fan runs and airflow is present to the drawer

This foam insulation wraps the refrigerator's water reservoir to reduce sweating and help prevent freezing, keeping dispenser flow consistent and the fresh food compartment dry. Replace if the original insulation is torn, crushed, or missing. What it does:

• Insulates the water reservoir to help maintain a stable temperature
• Helps prevent the reservoir from freezing, which can slow or stop dispenser flow
• Reduces condensation that can drip or puddle inside the refrigerator
• Restores proper cushioning and protection around the tank

• 1 foam insulation piece for the water tank

• Unplug the refrigerator and shut off the water supply before servicing
• Remove shelves/drawers to access the water reservoir area
• Carefully remove the old insulation; avoid stressing or puncturing the reservoir and tubing
• Fit the new foam snugly around the tank, reassemble, restore power/water, and check for leaks and dispenser flow

White

The air damper assembly regulates the flow of cold air from the freezer into the fresh food compartment. A new damper restores balanced airflow for steady refrigerator temperatures—helping prevent warm spots or unwanted freezing of items.

• Controls and meters cold-air supply from the freezer to the refrigerator section
• Helps maintain even, consistent temperatures across shelves and drawers
• A stuck or worn damper may cause a warm refrigerator section while the freezer stays cold
• If stuck open, may lead to freezing near the air outlet and noticeable temperature swings
• Failing dampers can produce repetitive clicking or grinding noises from the damper area

• Unplug the refrigerator before servicing
• Access from the fresh food compartment; remove shelves and the diffuser/cover to reach the damper
• Note screw locations and wiring; handle seals and air passages carefully to prevent leaks
• After installation, verify the damper door moves freely and the cover seats properly; allow up to 24 hours for temperatures to stabilize

Front mounting grommet.

This screw fastens appliance panels, brackets, and trim so parts stay secure and aligned. Replace a missing, stripped, or rusty screw to stop rattles and restore a tight, factory fit.

• Secures covers, brackets, and trim to the appliance cabinet or liner
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration noise and loose or misaligned parts
• Maintains proper fit of guards, kickplates, or internal panels

• Disconnect power; turn off water supply if working near water lines
• Match to the original fastener to size and thread
• Start threads by hand to avoid cross-threading; tighten snugly, not excessively
• If threading into plastic, avoid overtightening to prevent damage

Size: 10-32 GXTT FLP.595 S

Keep the refrigerator's rear fan assembly secure and airflow on track with this fan orifice bracket. It supports the fan shroud/orifice so the motor and blade stay aligned, helping maintain proper cooling and reduce vibration.

• Secures the fan orifice/shroud to the machine-compartment frame
• Maintains correct fan motor and blade positioning for smooth operation
• Helps direct airflow through the condenser area for effective heat removal
• Typical symptoms of a failed bracket include rattling/buzzing from the back, a loose or wobbling fan assembly, reduced airflow, or warm temperatures

• Disconnect power and move the refrigerator to access the rear machine compartment
• Remove the rear access cover; support the fan motor/blade before loosening fasteners
• Transfer any reusable mounting hardware to the new bracket; align the orifice/shroud properly
• Ensure the fan spins freely and the assembly is secure before reinstalling the rear cover and restoring power

This replacement screw secures panels, brackets, and other hardware in your appliance. Installing a new fastener restores a tight, rattle-free fit when the original is missing, stripped, or corroded, helping keep components properly aligned.

• Fastens components, trim, and brackets to the cabinet or frame
• Replaces a missing, stripped, or rusted screw
• Helps reduce rattles, vibration, and loose panels or handles
• Maintains proper alignment of panels and hardware

• Disconnect power (and water/gas if applicable) before servicing.
• 12-24 thread, approximately 0.90-inch length; match to the original location.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Replace any additional damaged fasteners to ensure even clamping and a secure fit.

This evaporator fan bracket secures the evaporator fan assembly behind the rear panel. A rigid, correct-fit mount preserves blade clearance and airflow across the evaporator coils for steady temperatures while minimizing vibration and noise.

• Holds the evaporator fan assembly firmly in position
• Maintains alignment and clearance to prevent fan rubbing and excess noise
• Supports proper airflow through the evaporator compartment for consistent cooling
• Replace if the bracket is cracked, warped, or loose; symptoms may include rattling, scraping sounds, or the fan contacting the shroud

• Disconnect power before servicing and use cut-resistant gloves
• Remove shelves/drawers and the rear evaporator cover to access the fan assembly
• Transfer the fan motor and existing hardware to the new bracket; ensure the blade spins freely without contact
• Avoid damaging the evaporator coils; reassemble panels and restore power to test

Lamp 40w chill

This bottom hinge pin supports and serves as the pivot for the refrigerator door. An accurate, tight-fitting hinge pin helps the door swing smoothly and seal properly to maintain temperature and reduce wear.

• Serves as the lower pivot point for the door on the bottom hinge
• Helps keep the door aligned for proper closing and gasket contact
• Replacing a worn pin can improve door movement and reduce stress on the hinge

• Unplug the appliance before servicing
• Support the door to relieve weight from the hinge before removing hardware
• Transfer any spacers/shims in their original order to maintain alignment
• Tighten fasteners securely and check door swing and seal after installation

This air diverter is a duct component that directs and balances airflow inside the refrigerator. Replacing a cracked or missing diverter helps restore proper cooling performance and reduce frost or condensation around air passages.

• Guides cold air from the evaporator through the intended duct path
• Helps maintain even temperatures between compartments
• Improves airflow seal and direction to reduce warm-air bypass
• Common symptoms: uneven cooling, weak airflow, frost/condensation near ducts, or visible damage to the diverter

• Disconnect power before servicing
• Remove shelves/drawers and the interior panel to access the diverter per your model's service information
• Note orientation and transfer any reusable screws/clips
• Do not overtighten fasteners into plastic; confirm unobstructed airflow before restoring power

This ice bucket and auger assembly stores ice in the freezer and drives it to the dispenser chute. Replacing a cracked bin or worn auger restores smooth, dependable dispensing of cubed or crushed ice from the door.

• Holds ice in the freezer and uses the auger to feed ice toward the dispenser opening
• Works with the bin's internal components to deliver cubed or crushed ice as selected
• Common symptoms: no ice dispensing, slow/intermittent dispense, grinding or clicking during dispense, or visible cracks/worn auger parts
• Restores reliable, consistent ice delivery from the dispenser

• Disconnect power to the refrigerator before servicing
• Remove the ice bin and empty any remaining ice
• Align the auger drive with the motor coupler; slide the bin fully into place to engage the drive
• Wear cut-resistant gloves; edges and crusher components can be sharp

Fresh food side. For the same part in black, purchase WR11X10009.

Freezer side.