Ra56233jq0 Parts

This center trim is the molded bezel that fits the front center of the cooktop/oven control area, restoring a finished look and protecting the control panel edges from heat and grime. What it does:

• Covers and protects the exposed edge of the control panel for a clean appearance
• Hides gaps, chips or discolored trim that make the console look worn
• Helps prevent dirt and grease from getting behind the control assembly
• Restores proper alignment and fit where the original trim is cracked or broken

• Disconnect power to the appliance before starting any repair.
• Typically secures with clips or screws—retain hardware and note orientation when removing old trim.
• Handle edges carefully; replacement may require gentle prying with a trim tool.
• If mounting hardware or support brackets are damaged, replace them separately.

Noise suppression kit. Mostly used on evaporator.

This broiler pan grid is the oven rack insert that holds food above the broil pan to promote even browning and let drippings fall away. It restores broiling performance for ovens using a two-piece broil pan set. What it does:

• Supports meats and vegetables during broiling so heat circulates around food for better sear and browning
• Allows drippings to fall into the lower broil pan to reduce smoke and flare-ups
• Replaces a missing, warped, or damaged grid that can cause uneven cooking or food slipping through
• Fits into the matching broil pan to restore original broiling configuration

• Ensure oven is off and grid has cooled before handling or installing
• Place grid into the broil pan with grid edges seated securely in the pan
• Clean after use with warm, soapy water; avoid harsh abrasives that can damage the finish

Package of 12

Sealer for refrigerant line insulation.

This compressor isolator is a rubber mount that cushions and reduces vibration and noise from the compressor, helping keep the appliance quieter and preventing metal-to-metal contact. What it does:

• Dampens compressor vibration to reduce noise and rattling
• Helps prevent compressor movement that can strain mounting hardware
• Reduces transfer of vibration to the cabinet and surrounding components
• Commonly replaced when vibration noise or scraping is heard from the base

• One compressor isolator (rubber mount)

• Disconnect power to the appliance before any service and work with the appliance unplugged
• Access may require tilting or moving the appliance; use safe lifting practices and get help if needed
• Inspect surrounding mounts and hardware; replace like-for-like and verify fit before final assembly

This is the left side, side curtain. For right side use WP8011308.

Size: 3/16 inch.

Size: 5/16 inch.

Size: 3/8 inch.

Size: 3/4 inch.

Size: 1/4 inch.

Includes 12 screws.

This bake element is the lower heating element inside the oven cavity. It supplies steady bottom heat during Bake cycles, helping the oven preheat properly and cook food evenly when the original element has failed.

• Provides the primary bottom heat during Bake mode
• Cycles with the oven control/thermostat to maintain set temperature
• Common failure symptoms: no heat in bake, very long preheat, uneven or undercooked results
• Visible damage may include blistering, cracks, or burned spots on the element sheath

• Disconnect power at the breaker and allow the oven to cool completely
• Remove racks; take out the element's mounting screws and gently pull the element forward to access the terminals
• Support and label wires; transfer them to the new element one at a time to avoid miswiring and prevent wires from slipping back
• Reinstall securely, restore power, and run a Bake test to verify operation

This is the range surface unit infinite switch for an 8-inch burner. It regulates power to the large surface element so you can set and maintain the desired heat level during cooking.

• Controls the temperature of an 8-inch surface (cooktop) element
• Replaces a switch that causes an 8-inch burner to be stuck on high, not heat, or only work intermittently
• Helps restore smooth, adjustable heat settings
• Designed for the large surface element circuit on compatible ranges

• Disconnect power before servicing; this is a high-voltage repair
• Note knob orientation and wire positions; take a photo for reference
• Transfer wires one at a time to the new switch to maintain correct connections
• Ensure the switch shaft and knob align properly before reassembly and testing