Ra724kwh Parts

This lower oven bake element provides the primary heat source for Bake cycles, restoring proper preheat and even, reliable cooking. Replace it if the oven won't heat, preheats slowly, or bakes unevenly.

• Heats from the bottom in Bake to reach and maintain set temperature
• Common symptoms: no heat in Bake, very slow preheat, oven temperature too low, or uneven results
• Visual clues: cracks, blisters, or burned spots on the element sheath
• If shorted, it may trip the circuit breaker when Bake is selected

• Disconnect power at the breaker and let the oven cool completely
• Remove racks, take out the element's mounting screws, and gently pull the element forward
• Hold wires so they don't retract; transfer and firmly connect the terminals; replace any heat-damaged connectors
• Reinstall element, ensure it's not contacting the cavity, restore power, and test Bake

This oven door gasket assembly seals the door to the oven frame to keep heat in and prevent hot air leaks. Replacing a worn seal restores proper preheat times, temperature stability, and more consistent baking performance.

• Forms a heat-resistant seal between the oven door and front frame
• Helps reduce heat loss and maintain set oven temperatures
• Common fix for heat leaking around the door, long preheat times, and uneven baking/roasting
• Replace if the gasket is torn, frayed, flattened, brittle, or missing retainer ends

• Disconnect power at the breaker and allow the oven to cool completely
• Open the door and remove the old gasket from its retainers; note clip/hook locations and orientation
• Clean the sealing surface/channel before installing
• Install the new gasket without stretching; fully seat all retainers and verify the door closes evenly

This speed nut is a clip-on fastener that provides threads for a screw on the appliance. It secures sheet-metal panels, brackets, or trim and helps keep assemblies tight under vibration and repeated use.

• Provides captive threads so a screw can tighten into thin sheet metal
• Helps secure panels, brackets, and trim pieces in place
• Replace if a screw spins without tightening, a panel rattles/feels loose, or the original clip is missing or damaged
• Restores a snug, reliable attachment point without a loose nut

• Disconnect power and, if applicable, shut off gas; allow the appliance to cool before servicing
• Note the clip's orientation; slide it onto the panel edge or stud as designed
• Start the screw by hand to avoid cross-threading; do not overtighten
• Wear cut-resistant gloves when handling sheet-metal parts

Top-heat thermostat that controls the oven's upper heating circuit to maintain proper temperature. Replacing a failing thermostat restores consistent broil/top-bake performance and helps the oven reach set temperatures reliably. What it does

• Regulates the oven's top/broil heating element by cycling the circuit on and off to hold set temperatures.
• Restores proper top-heat and browning when a failed thermostat causes inconsistent or weak broil performance.
• Addresses symptoms such as broil not activating, uneven top browning, or the oven struggling to reach set temperatures.
• Works with the oven's control system to maintain safe, repeatable top-heat operation.

• Disconnect power to the appliance at the breaker or unplug before starting; allow the oven to cool completely.
• Access varies by model; remove the required control or oven panels to reach the thermostat.
• Label or photograph wiring before disconnecting so connectors are returned to their original positions.
• After installation, restore power and verify proper broil/top-heat operation.

This capillary clip secures the oven thermostat's sensing bulb/capillary to the cavity wall so it stays correctly positioned for accurate temperature control. Replace a missing or damaged clip to prevent a sagging bulb and erratic oven performance.

• Holds the thermostat capillary tube/sensing bulb in place inside the oven
• Helps maintain consistent temperature regulation by keeping the bulb properly located
• Direct replacement for a broken, corroded, or missing clip
• Symptoms include a loose or dangling bulb, uneven baking, or temperature swings

• Disconnect power (and gas, if applicable) and allow the oven to cool completely
• Access the oven cavity; locate the thermostat sensing bulb and capillary along the wall or back panel
• Position the bulb/capillary and secure with the new clip; avoid kinking or crushing the tube
• Restore power, and test operation

This small retainer secures the surface element receptacle in a range or cooktop so the element plugs in straight and stays seated. Replacing a bent or missing clip helps restore a stable, reliable connection.

• Holds the surface element receptacle firmly to the cooktop or bracket
• Keeps the element plug aligned and fully seated
• Helps prevent arcing, heat damage, and intermittent burner performance from a loose receptacle
• Useful when the element feels wobbly or the receptacle shifts during use

• Disconnect power before servicing
• Lift the cooktop or access panel to reach the receptacle area
• Support the receptacle, release the old clip, and snap the new clip into place
• Ensure the receptacle is secure and aligned before reinstalling the element

This is the control knob for a surface burner's mini valve. It fits over the valve stem so you can turn the burner on/off and adjust the flame level smoothly and safely.

• Rotates the burner's mini valve to control gas flow and flame size
• Replaces a cracked, stripped, missing, or melted knob
• Helps when the knob no longer engages the valve or is hard to turn
• Restores normal feel and control of the burner

• Disconnect power and shut off gas before beginning work
• Pull the old knob straight off the valve stem; align and press the new knob on
• Do not force—verify the flat/D orientation on the stem matches the knob
• Test burner operation and knob travel after installation

This genuine replacement screw secures panels, trim and small components on compatible appliances to restore proper fit and prevent rattling or gaps. Use it when a missing or damaged fastener causes loose or misaligned parts. What it does:

• Fastens panels, bezels, trim pieces and small assemblies to the appliance frame
• Restores secure fit to eliminate rattling, vibration noise or loose trim
• Replaces stripped, rusted or missing screws that prevent proper alignment

• Disconnect power to the appliance before servicing to avoid electrical hazard
• Use the correct screwdriver or driver bit to prevent stripping the head
• Tighten securely but avoid over-torquing; excessive force can strip threads or crack plastics
• Keep removed fasteners organized to ensure correct reassembly

This silicon controlled rectifier (SCR) switches and regulates power to heating elements and motors in compatible appliances, restoring controlled current flow for proper operation. It's a direct-replacement electronic switching component. What it does:

• Acts as a solid-state switch to control AC power to heater or motor circuits
• Helps regulate current during timed or thermostatic cycles
• Common replacement when appliance shows intermittent heating, no heat, or erratic motor control
• Replaces a failed/shorted SCR that can cause blown fuses or control board errors

• One silicon controlled rectifier (single SCR)

• Intended for technicians or experienced DIYers; disconnect power before servicing
• Verify correct SCR orientation and secure the 8-32 screw terminal; avoid overtightening
• Observe ESD precautions and handle the part by non-conductive areas

This replacement screw secures appliance components and panels. Use it to replace a missing, stripped, or rusty fastener to restore a tight, rattle-free fit and keep assemblies properly aligned.

• Fastens brackets, trim, and panels securely to the appliance frame
• Replaces lost, worn, or corroded hardware
• Helps correct loose or wobbly parts and misalignment
• Reduces vibration or rattling caused by loose fasteners

• Disconnect power (and gas, if applicable) before servicing
• Match to the original and replace one-for-one to ensure correct length/thread
• Start by hand to avoid cross-threading; tighten snugly—do not overtighten
• If multiple screws secure a part, loosen/tighten evenly to maintain alignment

This replacement oven rack restores a safe, level surface for cookware inside the oven cavity. Replace a missing, bent, or damaged rack so you can load, slide, and position pans at the correct height.

• Supports bakeware and cookware in the oven; slides on the factory side rails
• Helps maintain proper spacing from heating elements for consistent results
• Common symptoms: rack is warped/bent, broken welds, flaking finish/rust, or it no longer slides smoothly
• Restores full oven capacity when a rack is missing

• Allow the oven to cool completely before handling racks
• To install, align with the side supports, tilt the front slightly upward to clear the stops, and slide into position
• Ensure both sides are fully seated and level before use
• Refer to your owner's manual for self-clean cycle recommendations regarding rack removal

This replacement screw fastens appliance components to restore secure fit and reduce vibration or panel movement. Simple, direct replacement for a missing or stripped fastener to help maintain proper assembly and operation. What it does:

• Secures panels, brackets or trim to keep parts aligned and prevent rattling
• Restores mounting where a lost or damaged screw causes loose or sagging components
• Helps maintain electrical and mechanical connections by keeping parts properly seated
• Small hardware solution for cosmetic and functional stability

• Use the correct sized screwdriver or driver bit to avoid stripping the head
• Inspect mating threads and replace if damaged; do not force a stripped screw
• Tighten until snug — avoid over-tightening which can crack plastic or strip threads
• If accessing areas near power or controls, disconnect appliance power first and follow all safety precautions

This oven rack is a replacement wire shelf that supports cookware and bakeware for standard ranges and ovens. It restores proper cooking clearance and helps maintain even heat circulation inside the oven. What it does:

• Provides a stable shelf for pots, pans and baking sheets during cooking or baking.
• Restores correct rack positioning when the original rack is missing, bent, or worn.
• Helps maintain proper airflow and even heat distribution by holding items off the oven floor.
• Fits into existing left/right rack supports and slides into place on oven rack guides.

• Remove power to the appliance before accessing the oven interior for safety.
• Install by sliding the rack into the oven's existing rack guides until fully seated.
• Handle with care; edges can be sharp and the rack will be hot after use.

This replacement leveling screw secures and adjusts an appliance's leg so the unit sits level and stable on the floor. Restores proper tilt for even door operation and stable performance. What it does:

• Replaces a worn or damaged leveling screw used to raise or lower an appliance leg
• Helps stop rocking, reduce vibration, and keep doors aligned
• Common fix when an appliance tilts forward/back or is uneven on the floor
• Works with the corresponding leveling leg/assembly to set final height

• Support the appliance before adjusting or removing leveling hardware to prevent tipping
• Use appropriate hand tools; tighten securely but avoid over-torquing
• No electrical disconnection is typically required, but unplug if working near electrical components
• If the leveling leg assembly is damaged, replace the entire leg/assembly per manufacturer instructions