Shp878wd5n/11 Parts

This factory fastener secures panels, brackets, or internal components in your appliance, helping keep assemblies tight and rattle-free. Replace missing or stripped screws to restore a secure fit and dependable operation.

• Fastens components to the appliance frame, chassis, or panel assemblies
• Helps maintain alignment and reduce vibration or rattling
• Replaces lost, rusted, or stripped screws during service
• Common signs it's needed: loose panel or handle, vibration noises, or parts that won't stay secured

• Disconnect power and shut off water or gas before servicing
• Match the screw's location and length to the original from your model
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver type/size specified for your model's screw head

This protective cover sheet mounts to the appliance's frame to shield and support nearby components. Replacing a damaged or missing panel helps keep wiring and mechanisms protected and securely mounted, reducing vibration and preventing premature wear.

• Shields internal components from debris, moisture, and accidental contact
• Helps maintain proper alignment and support of adjacent assemblies
• Can reduce rattling or vibration when correctly secured
• Replace if bent, cracked, corroded, or missing

• Disconnect power (and water supply if applicable) before servicing
• Wear cut-resistant gloves; panel edges can be sharp
• Note and retain original fasteners/clips for reuse
• Route wires and seals carefully to avoid pinching; align panel before tightening fasteners

This support is a factory replacement component that holds and stabilizes a specific part within your appliance so it stays aligned and secure. Replacing a cracked or missing support restores proper fit and helps prevent noise or binding.

• Provides structural support and alignment for the designated component
• Keeps parts seated securely to minimize movement and vibration during use
• A damaged or missing support can cause looseness, rattling, sagging, or misalignment
• Restores proper fit and function when the original is cracked, warped, or broken

• Disconnect power and shut off any gas/water supplies before servicing
• Refer to your model's parts diagram to identify location and orientation
• Install using the appliance's existing screws or clips; avoid overtightening to prevent damage
• Wear cut-resistant gloves; beware of sharp edges and pinch points

This lock clamp secures an appliance component or assembly so it stays properly seated during operation. Replacing a worn or missing clamp helps restore a stable, rattle-free fit and reliable performance. What it does:

• Holds mating parts together to prevent shifting or vibration
• Helps maintain correct alignment of the secured component
• Can resolve issues where a part won't stay attached or seated
• Restore normal operation when the original clamp is broken or missing

• One lock clamp

• Disconnect power (and shut off water/gas if applicable) before servicing
• Note the clamp's original orientation; take a photo to aid reassembly
• Seat the component fully, then engage the clamp securely without over-stressing it
• Reassemble and test for a firm, stable fit before returning the appliance to service

This temperature sensor (NTC) monitors wash temperature and reports it to the control so the cycle heats and advances correctly. Replacing a faulty sensor can restore proper cleaning performance and normal cycle times. What it does:

• Measures water temperature and sends resistance changes (NTC) to the control
• Helps the control regulate heating and cycle progression
• Failure symptoms can include no/insufficient heat, extended cycles, or poor drying
• May trigger a temperature-sensor fault (e.g., E11 on some models)

• 1 temperature sensor

• Disconnect power and turn off water supply before servicing
• Access is typically at the sump/heat-pump area; remove the toe-kick/lower panel as needed
• Expect some residual water; place a towel or tray to catch drips
• Ensure the sensor seats fully and the seal is in good condition to prevent leaks

The Spray Head is an OEM replacement part for Bosch dishwashers. It directs pressurized water along the dish racks, targeting every inch of dishware and cookware. Consistent coverage cleans thoroughly without waste.   

Symptoms of a bad spray head can include clogged nozzles, inconsistent patterns, or spray heads that do not oscillate and rotate properly through cycles. Mineral deposits pose blockage risks over time.

Causes of a bad spray head include:

• Uneven or skipped areas of spray coverage inside the machine
• Rotating/oscillating mechanisms that jam or continuously stick  
• Nozzles fully or partially blocked reducing water pressure
• Head assembly detaching from water tub wall or bracket

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This repair set renews the hinge pivot components so the door opens smoothly and closes squarely. Replacing the worn hardware helps maintain proper alignment and a tight gasket seal for consistent performance. What it does:

• Replaces worn hinge pin/bushing hardware to restore door support
• Helps fix a door that sags, scrapes, or won't close flush
• Can reduce clicking, squeaking, or grinding at the hinge
• Helps the door seal make full contact to prevent warm air leaks

• 1 repair set

• Disconnect power; if applicable, turn off the water supply
• Remove items from the door; support the door and lift it off the hinge
• Install the new hinge hardware in the original orientation
• Reinstall and align the door; verify gasket seal and adjust leveling if needed

The Wire Harness is an OEM part for Bosch dishwashers. It safely routes electrical signals between electronic control boards, switches, motors, and other components for proper function.

Causes of a bad wire harness can include short circuits due to moisture intrusion or physical damage over time such as cuts, kinks or exposed conductors from repetitive closing of the dishwasher door.

Symptoms of a bad wire harness include:

• Cycle or component malfunctions like improper washing or drying
• The control panel lighting or displays not responding
• Error codes displayed on controls
• Abnormal noises from internal motors or solenoids

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This factory screw secures select Bosch/BSH appliance components. Use it to replace a missing or damaged fastener so panels, brackets, or trim stay tight and rattle-free during operation.

• Tightens and holds appliance parts such as panels, brackets, or trim in place
• Helps correct issues like loose or vibrating panels caused by a missing/stripped screw
• Maintains proper fitment after service or disassembly
• Torx T20 drive head helps resist cam-out during tightening

• Unplug power and shut off any water supply before servicing
• Use a T20 Torx driver; hand-start to avoid cross-threading
• Do not overtighten—snug to manufacturer torque guidance if available
• Replace any additional missing or damaged fasteners for even clamping

This Bottom Case is the lower housing of the appliance. It forms the structural base that supports and protects internal components, helping restore proper alignment and stability when the original base is cracked, warped, or damaged.

• Provides the mounting base for key assemblies and exterior panels
• Helps protect internal parts from impact and debris
• Maintains chassis alignment to reduce vibration, rattling, or poor panel fit
• Replace if the original base is broken, warped, or otherwise compromised

• Disconnect power and, if applicable, shut off water before servicing
• Edges can be sharp; wear cut-resistant gloves and eye protection
• Access typically requires removing lower/outer panels; transfer any hardware or seals from the old base
• Before reassembly and testing

The Ventilation Duct is an OEM part for Bosch dishwashers. It is a molded plastic component situated at the top of the appliance that serves two critical functions.

The ventilation duct allows steam and vapors produced during washing and drying cycles to efficiently escape. The duct also serves as the channel through which hot air is directed during the drying phase to evaporate water from clean dishes. 

Causes of a failed ventilation duct can include cracks that compromise a tight seal, or blockages obstructing smooth flow.

Symptoms of a bad ventilation duct include:

• Puddles or standing water inside the dishwasher
• Dishes failing to fully dry at the end of cycles
• High humidity or moisture trapped inside the appliance
• Hot air not properly channeled through the drying passages

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Threaded nut used to secure components on a bolt or stud inside your appliance. Replacing a stripped or missing nut restores proper clamping force and helps prevent loosening from vibration, temperature changes, and normal operation. What it does:

• Secures parts together on a threaded fastener to maintain alignment and clamp load
• Resists loosening from vibration and heat cycles when properly tightened
• Helps prevent rattling, leaks, or shifting components caused by loose hardware
• Replace if threads are worn, rounded, corroded, or the nut will not hold torque

• 1 nut

• Disconnect power and shut off water or gas to the appliance before servicing
• Support the component and start the nut by hand to avoid cross-threading
• Tighten with the correct tool to the manufacturer's specified torque; do not overtighten
• Replace companion washers/gaskets if required by the service manual and confirm alignment before final tightening

The Indicator Light is an OEM part for Bosch dishwashers. It serves as a visual cue, providing important status updates and notifications related to the dishwasher's operation.

Causes of a malfunctioning Indicator Light can stem from issues with the control board or wiring harness that powers the light, or the light itself burning out due to age or electrical surges.

Symptoms of a bad Indicator Light include:

• The light not illuminating at all, even when it should be on
• Flickering or dimming of the light during operation
• The wrong indicator light turning on or staying on inappropriately

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This factory fastener secures panels, brackets, and internal components in your appliance. Replacing a missing or damaged screw restores a snug fit, reduces vibration and rattles, and keeps assemblies properly aligned during service or reassembly.

• Anchors panels, trim, and internal parts to the appliance frame or subassemblies
• Helps prevent vibration, buzzing, and loose or shifting components
• Ideal replacement for lost, stripped, or corroded hardware
• Common symptoms include loose panels, gaps, rattling noises, or parts that won't stay secured

• Disconnect power and shut off water or gas before servicing
• Match this screw to the original and replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; use the correct driver and do not overtighten
• Inspect the mating clip/insert; replace if stripped or damaged for a secure hold

The Facia Panel is an OEM part for Bosch dishwashers. As the central interface, the facia panel houses all function buttons, cycle/option selectors, and status LED lights.

The facia maintains a sleek appearance while clearly presenting settings. Integrated controls allow for customized washes tailored to any load.

Causes of a bad facia panel can include normal wear from thousands of touches over the years. Exposure to steam and detergents may deteriorate electronics or graphics over time as well. Accidental impacts pose a hazard.

Symptoms of a bad facia panel include:

• Non-responsive or unreliable touch buttons
• Faded labels or instructions that are difficult to read
• Loose panel assembly or mounting points
• Faulty status lights or improper sequencing

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This stud secures internal components and panels, providing a threaded anchor point that keeps parts aligned and stable for safe operation. It's a simple replacement that restores proper mounting when the original stud is missing, cracked, or stripped. What it does:

• Provides a threaded attachment point for securing panels, terminals, or assemblies
• Restores stable mounting when a factory stud is broken, bent, or stripped
• Helps eliminate rattling or loose connections caused by missing hardware
• Allows safe reassembly after service or part replacement

• Disconnect power and follow all safety procedures before servicing the appliance
• Use the correct size wrench or socket; thread carefully to avoid cross-threading
• Do not overtighten—tighten to snug fit consistent with surrounding hardware
• Repair or replace the mating component before installing