Shu43c06lc C/22 Parts

This is the right side hinge plate. For left side use 00298567.

Bushing included. To order bushing separately use 00165296. This is the left side hinge. For right side hinge use 00263119.

This outer door is the dishwasher's exterior front panel that restores the appliance's appearance and protects internal components from damage. It provides a finished look and replaces dented, scratched, or corroded panels. What it does

• Covers and protects the inner door assembly, controls, and insulation from impact and moisture.
• Restores the dishwasher's exterior finish and alignment for proper sealing.
• Helps prevent further cosmetic damage and exposure-related corrosion.
• Resolves issues where visible dents, deep scratches, or rust affect the door surface.

• One outer door panel only.

• Disconnect power and water supply before starting any repair.
• Door panels can be heavy or awkward—have a second person assist to avoid dropping or bending the panel.
• Follow the manufacturer's service manual for correct removal/reinstallation steps and torque specifications.
• If trim, latch, or control components are attached, verify whether they must be transferred from the old door.

Color: White.

Bushing included. To order bushing separately use 00165296. This is the right side hinge. For left side hinge use 00263115.

This is the left side hinge plate. For right side use 00298570.

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

A reed switch door sensor that detects when the appliance door is closed so the control can start cycles. Replaces a failed magnetic sensor to restore reliable door-closed detection and normal operation. What it does

• Acts as a magnetic contact that signals the control when the door or lid is closed
• Helps prevent the appliance from starting if the door is open or not fully latched
• Common symptom fix for no-start, intermittent cycle start, or control not recognizing a closed door
• Works as the electrical switching element in the door/detector assembly

• One reed switch (single replacement sensor)

• Disconnect power to the appliance before replacing the part to avoid shock or damage
• Handle the switch and wiring gently; avoid bending or stressing terminals and solder joints
• Locate and access the door/detector area per your service manual or tech sheet; confirm connector orientation before installing

This shaft for the float switch is the replacement shaft that secures and guides the dishwasher float to accurately detect water level, helping the appliance fill and shut off properly. Direct-fit design replaces the worn or broken float shaft. What it does

• Guides the float so the level-sensing switch can detect low or high water levels.
• Prevents overfilling by ensuring the float actuates the water-level switch reliably.
• Commonly replaces a cracked, bent or missing shaft that causes inconsistent fill, continuous filling, or water-level errors.

• One replacement float switch shaft.

• Disconnect power to the appliance before starting any repair.
• Remove the access panels and float assembly per your model's service instructions to reach the shaft.
• Inspect the float and switch for damage; replace only the failed components as needed.
• Reassemble carefully and test fill/stop operation before returning the appliance to service.

This control unit is the dishwasher's main electronic control board that manages cycles, timing, and user commands so the appliance runs the selected wash programs reliably. Replace a failed board to restore normal control operation. What it does

• Receives input from the touchpad/controls and starts or stops wash cycles
• Manages cycle timing, valves, pumps and heater signals according to selected program
• Communicates error conditions to the display or control indicators
• Common symptoms: unresponsive controls, display errors, cycles that won't start or complete

• Disconnect power at the breaker or unplug the appliance before service
• Handle the board by edges and avoid static discharge (use an anti-static wrist strap if available)
• Verify connectors seat fully and match original wiring; do not force connections