Shv57c03uc/47 Parts

This drain hose adapter connects the appliance's drain hose to another hose or a compatible fitting, providing a secure, leak-resistant joint so wastewater can be routed to the household drain. Replace when the original adapter is cracked or loose.

• Couples the drain hose to another hose or to a sink/disposal/standpipe fitting
• Helps seal the joint to reduce leaks and hose slippage
• Restores a tight fit when the original adapter is worn, brittle, or missing
• Symptoms of a bad adapter: leaking at the connection, hose won't stay attached, visible cracks

• Disconnect power and turn off water before servicing
• Place a towel or pan to catch residual water from the hose
• Fully seat hose ends over the adapter barbs and secure with appropriate hose clamps
• Run a short test cycle and inspect all connections for leaks

The Instant Water Heater is an OEM part for Bosch dishwashers. It is responsible for heating the water to optimal temperatures during the cleaning cycle through its internal heating element and thermostat. 

Causes of failure can be attributable to scale build-up over time inhibiting heat transfer, cracks in heating elements, or thermostat malfunctions.

Symptoms of a bad water heater include:

• Incomplete cleaning even on high-temperature cycles
• Dishes not reaching appropriate sanitization temperatures
• Hot water not dispensing properly during the cycle
• Slow water heating causing extended cycle times

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This O-ring seals the NTC (negative temperature coefficient) temperature sensor where it inserts into the appliance. It restores a watertight seal at the sensor port to help prevent leaks and maintain reliable temperature-sensing performance.

• Provides a leak-tight seal between the NTC temperature sensor and its housing/tub/sump
• Helps prevent water seepage and moisture intrusion around the sensor opening
• Common symptoms of a failed seal: drips near the base, moisture in the leak tray, flattened/cracked ring, or a sensor that feels loose
• Good practice to replace when the NTC sensor is removed for service

• Disconnect power and shut off water supply before servicing
• Access the NTC sensor, remove the old O-ring, and clean mating surfaces
• Lightly moisten the new O-ring with water; seat it evenly to avoid pinching, then reinstall the sensor fully
• Run a brief test cycle and inspect for leaks

This O-ring is a circular sealing gasket that creates a watertight joint between mating parts. Replacing a flattened or cracked ring restores a tight seal and helps prevent leaks during operation.

• Provides a compressible seal between fittings, hoses, or housings
• Helps prevent drips and leaks at joints under normal system pressure
• Maintains proper flow by keeping connections sealed
• Typical failure signs: visible cracking/flattening, seepage at a joint, pooling water near the appliance

• Disconnect power and shut off the water supply before servicing
• Relieve any line pressure and place a towel to catch residual water
• Clean and inspect mating surfaces; replace any damaged components
• Lightly lubricate the O-ring with approved silicone lubricant, seat evenly without twisting, and test for leaks after reassembly

The Indicator Light is an OEM part for Bosch dishwashers. It serves as a visual cue, providing important status updates and notifications related to the dishwasher's operation.

Causes of a malfunctioning Indicator Light can stem from issues with the control board or wiring harness that powers the light, or the light itself burning out due to age or electrical surges.

Symptoms of a bad Indicator Light include:

• The light not illuminating at all, even when it should be on
• Flickering or dimming of the light during operation
• The wrong indicator light turning on or staying on inappropriately

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Small replacement O-ring that seals the dishwasher aqua sensor assembly to maintain a watertight seal and help ensure reliable sensor operation. Fits the sensor housing to reduce leaks and protect internal electronics. What it does:

• Seals the aqua/sensor housing to prevent water from escaping the sensor area
• Helps maintain accurate sensor readings by keeping the sensor dry and properly seated
• Commonly replaced when you see water pooling or dripping near the sensor assembly
• Used during aqua-sensor, pump, or housing repairs where the original seal is damaged

• Always disconnect power and turn off the water supply before starting repairs
• Replace the O-ring only when the sensor or housing is disassembled; inspect mating surfaces for damage or debris
• Ensure the O-ring is seated evenly in its groove before reassembly to avoid pinching or leaks

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

This is the right side hinge plate. For left side use 00298567.

This is the left side hinge plate. For right side use 00298570.

This electrical control switch completes or interrupts the power circuit that runs a specific appliance function, restoring on/off control for responsive operation and safer use. What it does:

• Acts as the user-activated or circuit-activated on/off control for a discrete function
• Restores power flow when the switch is made, allowing the associated component or cycle to run
• Common symptom: appliance function won't start or respond when the control is pressed or activated
• Common symptom: intermittent operation or no power to a given feature

• One switch

• Disconnect power to the appliance before attempting any service to prevent shock
• Access and replacement steps vary by model; follow the appliance service manual or schematic for safe disassembly
• Handle connectors carefully and confirm secure wiring/terminal seating after installation

This clamp secures a wooden or custom exterior panel to the appliance door, restoring proper panel alignment and reducing rattling or looseness. Designed to match the OEM bracket location and fit. What it does:

• Holds the decorative wood panel firmly against the dishwasher door frame
• Prevents the panel from shifting, sagging, or vibrating during cycles
• Restores even door fit and helps maintain the door's seal and appearance
• Works at the bracket attachment point to stabilize panel-to-door connection

• Disconnect power to the appliance before beginning any work
• Remove the outer door panel per the service manual to access the clamp location
• Inspect surrounding clips and screws; replace any damaged fasteners for a secure fit

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

A reed switch door sensor that detects when the appliance door is closed so the control can start cycles. Replaces a failed magnetic sensor to restore reliable door-closed detection and normal operation. What it does

• Acts as a magnetic contact that signals the control when the door or lid is closed
• Helps prevent the appliance from starting if the door is open or not fully latched
• Common symptom fix for no-start, intermittent cycle start, or control not recognizing a closed door
• Works as the electrical switching element in the door/detector assembly

• One reed switch (single replacement sensor)

• Disconnect power to the appliance before replacing the part to avoid shock or damage
• Handle the switch and wiring gently; avoid bending or stressing terminals and solder joints
• Locate and access the door/detector area per your service manual or tech sheet; confirm connector orientation before installing

This shaft for the float switch is the replacement shaft that secures and guides the dishwasher float to accurately detect water level, helping the appliance fill and shut off properly. Direct-fit design replaces the worn or broken float shaft. What it does

• Guides the float so the level-sensing switch can detect low or high water levels.
• Prevents overfilling by ensuring the float actuates the water-level switch reliably.
• Commonly replaces a cracked, bent or missing shaft that causes inconsistent fill, continuous filling, or water-level errors.

• One replacement float switch shaft.

• Disconnect power to the appliance before starting any repair.
• Remove the access panels and float assembly per your model's service instructions to reach the shaft.
• Inspect the float and switch for damage; replace only the failed components as needed.
• Reassemble carefully and test fill/stop operation before returning the appliance to service.