Shv68tl3uc/09 Parts

This lock clamp secures an appliance component or assembly so it stays properly seated during operation. Replacing a worn or missing clamp helps restore a stable, rattle-free fit and reliable performance. What it does:

• Holds mating parts together to prevent shifting or vibration
• Helps maintain correct alignment of the secured component
• Can resolve issues where a part won't stay attached or seated
• Restore normal operation when the original clamp is broken or missing

• One lock clamp

• Disconnect power (and shut off water/gas if applicable) before servicing
• Note the clamp's original orientation; take a photo to aid reassembly
• Seat the component fully, then engage the clamp securely without over-stressing it
• Reassemble and test for a firm, stable fit before returning the appliance to service

This temperature sensor (NTC) monitors wash temperature and reports it to the control so the cycle heats and advances correctly. Replacing a faulty sensor can restore proper cleaning performance and normal cycle times. What it does:

• Measures water temperature and sends resistance changes (NTC) to the control
• Helps the control regulate heating and cycle progression
• Failure symptoms can include no/insufficient heat, extended cycles, or poor drying
• May trigger a temperature-sensor fault (e.g., E11 on some models)

• 1 temperature sensor

• Disconnect power and turn off water supply before servicing
• Access is typically at the sump/heat-pump area; remove the toe-kick/lower panel as needed
• Expect some residual water; place a towel or tray to catch drips
• Ensure the sensor seats fully and the seal is in good condition to prevent leaks

The Spray Head is an OEM replacement part for Bosch dishwashers. It directs pressurized water along the dish racks, targeting every inch of dishware and cookware. Consistent coverage cleans thoroughly without waste.   

Symptoms of a bad spray head can include clogged nozzles, inconsistent patterns, or spray heads that do not oscillate and rotate properly through cycles. Mineral deposits pose blockage risks over time.

Causes of a bad spray head include:

• Uneven or skipped areas of spray coverage inside the machine
• Rotating/oscillating mechanisms that jam or continuously stick  
• Nozzles fully or partially blocked reducing water pressure
• Head assembly detaching from water tub wall or bracket

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This replacement spring restores proper tension in the specific mechanism it supports, helping the connected component operate smoothly. A worn or broken spring can cause weak action, poor latching, or parts that won't return or stay in position.

• Provides controlled tension/return force for moving parts per your model's design
• Helps doors, lids, latches, or dispenser mechanisms open/close or release reliably
• Symptoms of failure can include weak or uneven tension, components not staying shut/open, or sluggish operation
• Replace if the spring is stretched, broken, deformed, corroded, or missing

• Disconnect power and shut off water supply before servicing
• Note the spring's orientation and anchor points; take a photo for reference
• Use needle-nose pliers for removal/installation and avoid over-stretching
• If your model uses paired springs, replace both to maintain balanced tension

This repair set renews the hinge pivot components so the door opens smoothly and closes squarely. Replacing the worn hardware helps maintain proper alignment and a tight gasket seal for consistent performance. What it does:

• Replaces worn hinge pin/bushing hardware to restore door support
• Helps fix a door that sags, scrapes, or won't close flush
• Can reduce clicking, squeaking, or grinding at the hinge
• Helps the door seal make full contact to prevent warm air leaks

• 1 repair set

• Disconnect power; if applicable, turn off the water supply
• Remove items from the door; support the door and lift it off the hinge
• Install the new hinge hardware in the original orientation
• Reinstall and align the door; verify gasket seal and adjust leveling if needed

The Frame is an OEM part for Bosch dishwashers that provides support and organization for your cutlery, offering a designated space for your forks, knives, spoons, and other utensils. 

A bad frame can occur due to wear and tear, accidental damage, or exposure to harsh chemicals. Signs of a faulty frame include cracks, broken sections, or difficulty in smoothly sliding the drawer in and out.

Symptoms of a bad frame include:

• Cracks or broken sections in the frame 
• Difficulty in sliding the cutlery drawer in and out
• Unorganized or unstable storage of cutlery 

Replace your damaged or worn-out frame with this genuine OEM Bosch part to restore your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This factory screw secures select Bosch/BSH appliance components. Use it to replace a missing or damaged fastener so panels, brackets, or trim stay tight and rattle-free during operation.

• Tightens and holds appliance parts such as panels, brackets, or trim in place
• Helps correct issues like loose or vibrating panels caused by a missing/stripped screw
• Maintains proper fitment after service or disassembly
• Torx T20 drive head helps resist cam-out during tightening

• Unplug power and shut off any water supply before servicing
• Use a T20 Torx driver; hand-start to avoid cross-threading
• Do not overtighten—snug to manufacturer torque guidance if available
• Replace any additional missing or damaged fasteners for even clamping

The Indicator Light is an OEM part for Bosch dishwashers. It serves as a visual cue, providing important status updates and notifications related to the dishwasher's operation.

Causes of a malfunctioning Indicator Light can stem from issues with the control board or wiring harness that powers the light, or the light itself burning out due to age or electrical surges.

Symptoms of a bad Indicator Light include:

• The light not illuminating at all, even when it should be on
• Flickering or dimming of the light during operation
• The wrong indicator light turning on or staying on inappropriately

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This factory fastener secures panels, brackets, and internal components in your appliance. Replacing a missing or damaged screw restores a snug fit, reduces vibration and rattles, and keeps assemblies properly aligned during service or reassembly.

• Anchors panels, trim, and internal parts to the appliance frame or subassemblies
• Helps prevent vibration, buzzing, and loose or shifting components
• Ideal replacement for lost, stripped, or corroded hardware
• Common symptoms include loose panels, gaps, rattling noises, or parts that won't stay secured

• Disconnect power and shut off water or gas before servicing
• Match this screw to the original and replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; use the correct driver and do not overtighten
• Inspect the mating clip/insert; replace if stripped or damaged for a secure hold

The Installation Set is an OEM part for Bosch brand dishwashers. It includes all the necessary mounting brackets and hardware required to securely install the dishwasher into the cabinetry cavity beneath the kitchen counter. 

Symptoms of a bad mounting set include:

• Loose fit of the dishwasher in the opening that allows side-to-side movement 
• Visible gaps around the perimeter of the unit once installed
• Sagging or inability to fully open or close the dishwasher door

Causes of a bad mounting set can include broken mounting brackets, corroded or damaged hardware, or missing screws, washers, or fittings that compromise a tight mounting installation. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers.
 

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

This control module is the appliance's program board that manages electronic controls and cycle operation. Replacing a failed module helps restore proper control response and reliable cycle management. What it does:

• Manages program logic, cycle timing and selection for the appliance
• Processes inputs from buttons, sensors and the user interface
• Routes signals to motors, valves and other components to run cycles
• Common symptoms of a failing module: unresponsive controls, error codes, failure to start, or interrupted/incorrect cycles

• Disconnect power to the appliance before servicing to avoid shock
• Use anti-static precautions and avoid touching circuit traces or connector pins
• Note connector and cable orientation; ensure all plugs and ribbon cables are fully seated on reassembly

This replacement dishwasher door handle restores a secure, easy-to-grip place to open and close the door, improving usability and appearance. Designed to match the original fit and mounting style for straightforward swap-out. What it does:

• Replaces a cracked, bent, or missing door handle so the door can be opened and closed safely
• Provides a solid grip to prevent slips and reduce stress on the door panel
• Restores factory appearance when the original handle is damaged or worn
• Helps prevent further cabinet or door edge damage from makeshift grips

• Disconnect power to the appliance before starting any repair to avoid injury
• Many installations require removing the inner door panel to access mounting screws; keep hardware organized
• Use basic hand tools (screwdriver, nut driver) and avoid overtightening fasteners to prevent damage

This holder secures internal components to keep assemblies aligned and stable, reducing vibration and wear. It's a simple replacement that restores proper fit where a broken or missing clip causes loose panels or noisy operation. What it does

• Secures and aligns panels or wiring harnesses inside the appliance
• Prevents rattling, vibration, and misalignment caused by damaged or missing clips
• Helps maintain proper component spacing to avoid wear or interference
• Restores secure attachment after breakage or plastic fatigue

• Disconnect power and water before starting any repair
• Remove access panels or trim to reach the damaged clip—keep fasteners organized
• Press or snap the holder into place; replace any broken tabs before reassembling
• If plastic anchors are damaged, replace them with matching OEM clips

This replacement worm gear is a small plastic drive gear that transmits rotational motion between the motor and driven components, restoring normal gear-driven movement and reducing slipping or grinding. What it does:

• Transfers torque from the motor to the mating gear or gearbox for proper mechanical operation
• Replaces worn, stripped, or damaged worm teeth that cause slipping or loss of drive
• Stops grinding, clicking, or intermittent movement when the gear is the fault
• Helps restore smooth, consistent operation of the driven mechanism when installed correctly

• One worm gear

• Disconnect power to the appliance before beginning any repair
• Inspect mating gears and shafts for wear; replace worn parts to prevent repeat failure
• Use OEM-approved lubricant only where specified; do not force or overtighten mating components

This electronic operating module (programmer) controls a range of appliance functions and restores proper cycle selection and timing when the control board fails. Replaces a failed or unresponsive control module to help the appliance run intended cycles reliably. What it does:

• Manages cycle selection, timing, and user interface inputs on the appliance
• Receives commands from the control panel and operates relays/valves/motors accordingly
• Can correct symptoms like unresponsive controls, failure to start cycles, or erratic cycle behavior
• Resolves intermittent operation or incorrect cycle advancement when the original module is faulty

• One operating module (programmer)

• Disconnect power (unplug or shut off circuit breaker) before starting any work
• Handle the module carefully to avoid electrostatic damage; ground yourself before touching electronics
• Replacement may require reconnecting wiring harnesses and securing the module in its mounting; follow the appliance's service manual for exact procedure