Shx333a05uc/14 Parts

This hose clamp secures a rubber or plastic hose to its fitting inside the appliance, helping prevent leaks at connection points. Replace a stretched, corroded, or damaged clamp to maintain a tight, reliable seal.

• Clamps the hose to a barb or fitting to keep it from slipping off
• Helps maintain a watertight connection and reduce drips at the joint
• Can help resolve leaks caused by a loose hose connection
• Common signs: moisture around a hose joint, visible rust/deformation, or a clamp that won't tighten

• Disconnect power and turn off the water supply before servicing
• Place a towel or tray to catch residual water; note hose routing and clamp position
• Use appropriate hand tools for your clamp style; fully seat the hose and tighten evenly
• After reassembly, run a brief test and inspect for leaks at the connection

This is the right side hinge plate. For left side use 00298567.

Spring-style hose clamp that secures flexible water hoses to fittings on select appliances, helping maintain a leak-tight connection at hose joints. Keeps hoses seated to reduce leaks and ensure reliable water flow. What it does:

• Holds flexible inlet, drain, or circulation hoses tightly on barbed fittings and nipples.
• Prevents leaks and water loss at hose connections by maintaining steady clamp pressure.
• Common signs it needs replacement: dripping or pooling near hose connections, a loose or wobbly hose, or visible clamp corrosion or deformation.
• Small, inexpensive part that restores a secure hose connection when the original clamp has failed.

• Always disconnect power and shut off the water supply before servicing appliance plumbing.
• For spring-style clamps, use pliers to open the clamp, position it over the hose, and release slowly so it seats properly; ensure the hose is fully pushed onto the fitting.
• Inspect the hose and fitting for damage; replace the hose if cracked or excessively worn before installing a new clamp.
• Wear eye protection when compressing or releasing spring clamps to avoid injury from sudden release.

This is a genuine OEM washer sourced directly from the manufacturer for use in many dishwashers and other appliances. Washers are used to help distribute the load a screw or bolt carries when connecting components. For example, in a dishwasher, the handle has two screws, one on each side, connecting it to the central unit. These screws have washers on them that help the screws bear the weight of pulling the dishwasher door open and closed repeatedly. Over time, the washers may warp and become loose, causing them not to sit flush on the screw. When the washers are damaged, they should be replaced to prevent further damage. Before working on the dishwasher, disconnect the power source. Locate the screw and washer that need to be replaced. Remove the screw and take the washer off the end. Install a new washer on the screw and reinstall it in the dishwasher. Reconnect the power. This washer is made of high quality metal; it is sold as an individual unit. Screws are not included with the washer. This washer is specifically designed for use in dishwashers manufactured by Bosch.

A replacement door handle that restores a secure grip and the appearance of the appliance door. Durable, user-replaceable design helps address common wear and damage so the door opens and closes with a solid feel. What it does:

• Provides a secure grip for opening and closing the appliance door.
• Replaces cracked, loose, bent, or cosmetically damaged handles.
• Restores original door alignment and user feel when the existing handle is failing.
• Matches OEM-style fit and mounting locations for a straightforward swap on compatible models.

• Disconnect power and, if applicable, water supply before beginning repair; empty the door area.
• Typical installation requires removing exterior trim or the inner door panel and unscrewing the old handle; save mounting hardware if reusable.
• Use proper-size screwdrivers and avoid overtightening fasteners to prevent damage.

Bushing included. To order bushing separately use 00165296. This is the left side hinge. For right side hinge use 00263119.

This electronic control unit regulates dishwasher cycles and key electronic functions so the appliance runs the selected programs and responds to controls. Replacing a faulty control restores proper cycle selection and timing for reliable operation. What it does:

• Controls wash, rinse and drain cycles by sending signals to valves, pumps and heaters
• Interprets user inputs from the console and starts or cancels selected programs
• Monitors and reports electronic errors that can prevent normal operation
• Symptoms of failure include a blank or unresponsive control panel, failure to start cycles, unexpected error codes, or erratic cycle behavior

• Disconnect power to the appliance before starting work to avoid shock
• Handle the board carefully; avoid touching circuit traces and use ESD precautions if possible
• Verify connector alignment and secure all plugs before restoring power

This is the left side hinge plate. For right side use 00298570.

This electrical control switch completes or interrupts the power circuit that runs a specific appliance function, restoring on/off control for responsive operation and safer use. What it does:

• Acts as the user-activated or circuit-activated on/off control for a discrete function
• Restores power flow when the switch is made, allowing the associated component or cycle to run
• Common symptom: appliance function won't start or respond when the control is pressed or activated
• Common symptom: intermittent operation or no power to a given feature

• One switch

• Disconnect power to the appliance before attempting any service to prevent shock
• Access and replacement steps vary by model; follow the appliance service manual or schematic for safe disassembly
• Handle connectors carefully and confirm secure wiring/terminal seating after installation

The Tube Dishwasher is an OEM component for Bosch dishwashers. It is responsible for circulating water throughout critical spray arms during different cycles. 

Causes of a bad tube dishwasher can include mineral buildup reducing the tube diameter over time, physical damage from scraping dishware against the pipes, or wear from normal vibration/motion.

Symptoms of a bad tube dishwasher include:

• Incomplete spray coverage in hard-to-reach areas  
• Soft or spotty cleaning performance in certain sections
• Puddles or leaks at the tube installation points
• Dirty or stagnant water unable to circulate properly

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Power Cord is an OEM part for Bosch dishwashers. It serves the critical function of supplying electric current safely from the wall outlet to internal components. The power cord's insulation and grommet prevent water intrusion that could create a hazardous situation. 

Causes of a bad power cord can include normal wear and tear of the outer casing, cracks that expose internal wires, and severed connections disrupting current flow. 

Symptoms of a bad power cord include:

• The dishwasher fails to turn on or operate
• Loose connections at the wall outlet or rear of the appliance 
• Bare or frayed wire exposed from damaged insulation
• Shock or electrocution risk in a wet environment

Replacing your cord with this genuine OEM part restores a vital link to powered cleaning. For continued safe and reliable dishwasher use, this Bosch replacement cord is also compatible with some Thermador, Gaggenau, and Kenmore models.

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

This sleeve-style insulator protects wiring and components from heat and abrasion, helping maintain safe operation and reduce shorts or premature wear. It's a simple replacement that restores original clearance and protection. What it does:

• Covers and insulates wiring or terminals to prevent chafing and heat damage
• Helps reduce electrical shorts caused by worn or exposed conductors
• Restores proper spacing and component protection after panel or control repairs
• Commonly replaced when insulation is cracked, brittle, or missing

• One sleeve-style insulator (quantity: 1)

• Disconnect power to the appliance before inspecting or replacing electrical insulation
• Slide the sleeve onto the wire or over the terminal so it fully covers exposed conductor or contact points
• Verify routing and clearances so the insulated area does not contact sharp edges or high-heat surfaces
• Inspect surrounding wiring and components for additional damage and replace as needed

A reed switch door sensor that detects when the appliance door is closed so the control can start cycles. Replaces a failed magnetic sensor to restore reliable door-closed detection and normal operation. What it does

• Acts as a magnetic contact that signals the control when the door or lid is closed
• Helps prevent the appliance from starting if the door is open or not fully latched
• Common symptom fix for no-start, intermittent cycle start, or control not recognizing a closed door
• Works as the electrical switching element in the door/detector assembly

• One reed switch (single replacement sensor)

• Disconnect power to the appliance before replacing the part to avoid shock or damage
• Handle the switch and wiring gently; avoid bending or stressing terminals and solder joints
• Locate and access the door/detector area per your service manual or tech sheet; confirm connector orientation before installing