Shx3ac72uc/13 Parts

This is a Bosch dishwasher control board. The dishwasher's control board ensures that the various cycles and settings can be properly managed, such as the washing and draining cycles. If the user notices issues with dishes not coming out clean after a full cycle, the control board should be checked for error codes or signs of visible wear and tear that may indicate it needs to be replaced. Make sure that the dishwasher is turned off, unplugged, and completely disconnected from its power and water sources. It's recommended that work gloves are worn to prevent injury. This is a genuine OEM part and has been sourced directly from the manufacturer. This is an authentic part and as such is sold individually and made from durable, high-quality, non-corrosive materials to ensure the highest possible quality. This part is compatible with dishwashers that have been manufactured by Bosch, Thermador, Gaggenau, and various other brands.

Tall item spray head.
This Spray Head is an OEM part for Bosch Dishwashers. It plays a role in distributing water evenly during the dishwasher's washing cycles. Continuous exposure to hard water, debris, or mineral deposits can cause issues with this component.

What Causes a Bad Spray Head:
Hard water deposits, debris, or mineral buildup can clog or block the spray head, affecting its performance. Physical damage can also impair its functionality.

Symptoms of a Bad Spray Head:

• Inadequate cleaning of dishes
• Uneven water distribution
• Reduced water pressure during washing cycles

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.
 

This holder secures its mating component inside your appliance, keeping it correctly positioned and stable during operation. Replace a cracked, warped, or missing holder to restore proper support and prevent looseness, noise, or misalignment.

• Provides physical support for the intended part or panel
• Maintains correct position and alignment during operation
• Helps reduce vibration, rattling, or intermittent contact from a loose component
• Typical signs of failure: broken tabs, worn slots, missing piece, or a component that won't stay seated

• Disconnect power; if the appliance is water-connected, turn off the water supply before servicing
• Use your model's parts diagram to locate and orient
• Transfer and reuse original screws or clips as needed
• After installation, verify a secure fit and test operation

This temperature sensor (NTC) monitors wash temperature and reports it to the control so the cycle heats and advances correctly. Replacing a faulty sensor can restore proper cleaning performance and normal cycle times. What it does:

• Measures water temperature and sends resistance changes (NTC) to the control
• Helps the control regulate heating and cycle progression
• Failure symptoms can include no/insufficient heat, extended cycles, or poor drying
• May trigger a temperature-sensor fault (e.g., E11 on some models)

• 1 temperature sensor

• Disconnect power and turn off water supply before servicing
• Access is typically at the sump/heat-pump area; remove the toe-kick/lower panel as needed
• Expect some residual water; place a towel or tray to catch drips
• Ensure the sensor seats fully and the seal is in good condition to prevent leaks

This stress relief is a small strain-relief clip that protects wiring where the harness passes through the cabinet, reducing pull and chafing on connections. Replacing a worn clip helps prevent loose wires and intermittent electrical issues. What it does:

• Secures the appliance wiring at an entry point to reduce strain on terminals and connectors.
• Prevents chafing and abrasion of wire insulation where harnesses pass through the cabinet or mounting openings.
• Can reduce symptoms such as intermittent power, flickering controls, or visible loose/frayed wires at the harness.
• Simple mechanical part: no electrical function but critical for long-term wiring reliability.

• Disconnect power (unplug appliance or switch off breaker) before accessing wiring; turn off gas supply where applicable.
• Remove panels as needed to access the harness entry; seat the clip fully so wires are routed through the relief, not pinched.
• Inspect surrounding wiring and replace any frayed or damaged wires; do not use the clip to conceal damaged wiring.

This seal creates a tight, leak-proof interface between mating components inside your appliance. Replacing a worn seal helps stop drips and protects nearby parts for reliable, leak-free operation.

• Forms a watertight barrier between connected parts
• Replaces cracked, flattened, or deformed sealing material that can leak
• Helps address puddling, dampness, or seepage around the unit
• Maintains proper performance and helps prevent water damage to surrounding components

• Disconnect power and shut off the water supply before servicing
• Access the sealed joint and note the original orientation and seating depth
• Clean mating surfaces; do not use sealants unless specified by the manufacturer
• Seat the new seal evenly; lightly lubricate with a water-safe lubricant and run a test cycle to check for leaks

This is a screw. This is a genuine Bosch replacement screw and has been sourced directly from the manufacturer. This replacement part is a high-quality piece of standard hardware with many different applications. This Bosch screw is intended for use with multiple different dishwasher models. It's common over time and with regular usage for screws to easily become stripped, rusted, broken, or lost. This can lead to improper functionality of appliances. It's important to always use genuine manufacturer replacement screws to ensure the highest-quality materials and a proper fit. When installing screws, always follow proper guidelines and abide by appropriate safety measures. For proper installation instructions and usage guidance, it is always recommended to refer to the equipment diagram supplied specifically by the manufacturer. This replacement screw is designed to work with various models of dishwashers manufactured by Bosch, Thermador, and Gaggenau. Please note this screw is a genuine OEM part made of high-quality, durable, non-corrosive metal and is sold individually.

White tray handle that restores a secure grip and smooth operation to your appliance's tray. Direct-fit replacement that matches the original handle's mounting points for an easy, reliable swap-out. What it does:

• Provides a secure grip for pulling out and pushing in the appliance tray.
• Stabilizes the tray to help prevent tipping or accidental drops when loaded.
• Addresses symptoms like cracked, broken, loose, or missing handle that make the tray hard to open.
• Matches the original shape and mounting locations for proper fit and function.

• Disconnect power at the breaker or unplug the appliance before working near electrical components.
• Remove the tray or rack as needed to access mounting screws or clips; retain original hardware unless replacement hardware is specified.
• Align the handle with the mounting points and secure using the existing screws/clips; avoid over-tightening to prevent damage.

This front leveling leg supports and adjusts the appliance at the front, helping it sit stable and truly level. Replace a damaged or missing leg to restore proper height, stability, and smooth door alignment during everyday use.

• Provides height adjustment at the front to level the appliance
• Helps prevent rocking, vibration, and rattling
• Maintains correct cabinet/door alignment for proper operation
• Replace if the foot is cracked, stripped, missing, or won't adjust
• Common signs: unit wobbles, sits unevenly, or is difficult to level

• Disconnect power; if applicable, shut off water or gas. Pull the appliance forward and remove the toe-kick/access panel for clearance.
• Protect the floor; tilt or raise the front slightly to reach the leg.
• Unscrew the damaged leg; thread the new leg in by hand to avoid cross-threading.
• Adjust height until level front-to-back and side-to-side; verify stability before returning to service.

This factory screw secures select Bosch/BSH appliance components. Use it to replace a missing or damaged fastener so panels, brackets, or trim stay tight and rattle-free during operation.

• Tightens and holds appliance parts such as panels, brackets, or trim in place
• Helps correct issues like loose or vibrating panels caused by a missing/stripped screw
• Maintains proper fitment after service or disassembly
• Torx T20 drive head helps resist cam-out during tightening

• Unplug power and shut off any water supply before servicing
• Use a T20 Torx driver; hand-start to avoid cross-threading
• Do not overtighten—snug to manufacturer torque guidance if available
• Replace any additional missing or damaged fasteners for even clamping

The Support is an OEM part for Bosch dishwashers. This part supports the door hinges, ensuring that the dishwasher door opens and closes smoothly and securely. The hinge support is vital for maintaining the alignment of the door, preventing stress on other components, and ensuring a proper seal during operation to avoid leaks.

Causes of hinge support failure often include mechanical wear and tear from frequent use, accidental damage from forceful handling, or corrosion from exposure to moisture and cleaning chemicals.

Symptoms of a failing dishwasher door hinge support include:

• Difficulty in opening or closing the dishwasher door
• A door that hangs unevenly or does not close fully
• Noticeable creaks or squeaks during door movement
• Increased effort required to operate the door

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Dishwasher Inner Door Panel is an OEM part for Bosch dishwashers. It is located inside the dishwasher door and protects internal components. 

Symptoms of a bad inner door panel include:

• Scratches, cracks, or damage impairing the appearance of the door interior
• Loose screws or mounting points causing rattling 
• Difficulty closing or sealing the door properly

Causes of a bad inner door panel can include prolonged exposure to heat and steam, damage from impact or mishandling of dishes, or normal wear over time compromising the integrity of the panel. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Insulating Part is an OEM component specifically designed for Bosch dishwashers. This part plays an important insulating and sealing role, helping to keep heat and moisture contained within certain areas of the dishwasher. 

Causes of a bad insulating part can include damage or wear over time that compromises its insulating and sealing abilities. Cracks, tears, or compression of the insulating material are signs it needs replacement.

Symptoms of a bad insulating part include:

• Inefficient washing and drying performance due to loss of heat and moisture
• Higher energy costs as the dishwasher works harder to achieve the proper temperatures
• Dripping or pooling of water outside the intended areas  

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. Replace yours today and restore your dishwasher's optimal insulation and seal.
 

This factory fastener secures panels, brackets, and internal components in your appliance. Replacing a missing or damaged screw restores a snug fit, reduces vibration and rattles, and keeps assemblies properly aligned during service or reassembly.

• Anchors panels, trim, and internal parts to the appliance frame or subassemblies
• Helps prevent vibration, buzzing, and loose or shifting components
• Ideal replacement for lost, stripped, or corroded hardware
• Common symptoms include loose panels, gaps, rattling noises, or parts that won't stay secured

• Disconnect power and shut off water or gas before servicing
• Match this screw to the original and replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; use the correct driver and do not overtighten
• Inspect the mating clip/insert; replace if stripped or damaged for a secure hold

This electronic control board manages an appliance's main functions and cycles, restoring responsive controls and proper operation when the original control fails or behaves erratically. It helps bring back predictable, safe operation. What it does:

• Regulates electrical signals to motors, valves and user interface components to control cycles and timing.
• Resolves symptoms such as unresponsive or blank controls, incorrect cycle behavior, or intermittent/erratic operation.
• Restores proper communication between touchpads/displays and internal components when the original control is faulty.
• Prevents incorrect or stalled cycles caused by failed control electronics.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Handle the board by its edges and avoid static discharge; use an anti-static wrist strap if available.
• Refer to the appliance service manual for mounting and wiring instructions.

This stainless-steel dishwasher door handle replaces a worn or damaged handle and restores a clean, flush grip on the front of the dishwasher door. It provides a durable, easy-to-grasp surface for everyday use. What it does:

• Replaces the exterior door handle so you can open and close the dishwasher smoothly; common symptom is a loose, cracked, or broken handle.
• Restores the appliance's appearance by matching stainless finishes.
• Provides a secure, comfortable grip for normal operation.
• Mounts to the door with factory fastening points.

• Always disconnect power to the appliance before servicing.
• Installation typically requires removing the inner door panel or access cover; keep track of mounting hardware.
• Use the correct hand tools and avoid overtightening fasteners to prevent damage.