Shx68tl5uc/07 Parts

This facia panel is the finished front trim that covers and protects the appliance's control area, restoring the unit's appearance and shielding internal controls from dirt and damage. It gives a clean, factory look after replacement. What it does

• Replaces cracked, chipped or cosmetically damaged front trim to restore appearance
• Covers and protects control buttons and electronics from spills and debris
• Provides the proper mounting surface for control overlays and handles
• Helps maintain a finished, factory-aligned front on the appliance

• Disconnect power to the appliance before beginning any service
• Removal typically requires removing door trim or control bezel screws/clips; keep fasteners for re-use
• Handle carefully to avoid scratching the finish during installation

This replacement power cord restores mains power to compatible Bosch appliances, providing a safe, OEM-style connection so your appliance can turn on and run reliably. Use when the original cord is damaged or not supplying power. What it does

• Supplies electrical power from the wall outlet to the appliance for normal operation.
• Replaces frayed, cut, or melted cords that can cause intermittent power or no power.
• Helps eliminate loose connections that can cause arcing, flickering, or tripped breakers.
• Restores a secure, strain-relieved connection where the cord meets the appliance chassis.

• Always disconnect power at the breaker or unplug the appliance before beginning service.
• Follow the appliance wiring diagram and secure all terminal connections per the manufacturer instructions.
• Route the cord through strain reliefs and grommets to prevent chafing; use supplied or OEM fasteners if present.

This outer door panel is the exterior front skin of the door assembly. It restores the appliance's appearance and shields internal door components when the original panel is dented, bent, or otherwise damaged.

• Forms the visible outer surface of the door and mounts over the inner door assembly
• Shields internal door components from impact and exposure
• Replaces panels that are dented, scratched, creased, or visibly worn
• Can help correct door appearance issues caused by a warped or loose outer panel

• Disconnect power before servicing; wear cut-resistant gloves
• Open and support the door; remove perimeter screws to release the outer panel
• Transfer handle/trim and any reusable hardware from the old panel to the new one
• Align the new panel and tighten screws evenly; verify smooth door operation and proper latching

This replacement hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal. Replacing a worn clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place for reliable operation.

• Applies clamping force to hold a hose on a barb or stub connection
• Helps prevent leaks at hose joints
• Common symptoms: water leaking at a hose connection, hose slipping off, poor fill or drain performance
• Replace when the original is loose, corroded, distorted, or lost tension; also recommended when installing a new hose

• Disconnect power and shut off water supply before servicing
• Expect some residual water; protect the work area
• Note the clamp's position/orientation; use appropriate hand tools for the clamp style
• Ensure the hose is fully seated and clamp is secure; run a test cycle and check for leaks

This insulating part installs in the specified location to help reduce heat transfer between internal spaces and exterior panels. Replacing a worn or missing insulator helps protect nearby components and maintain proper operating temperatures.

• Provides a thermal barrier to limit heat transfer to surrounding panels and wiring
• Helps prevent scorching or heat damage to adjacent components
• Restores proper insulation where the original has deteriorated or is missing
• Common signs of failure: visible damage or fraying, burnt odor, or unusually hot exterior areas

• Disconnect power and allow the appliance to cool completely before servicing
• Wear gloves and eye protection; insulation fibers can irritate skin and eyes
• Match the original orientation/placement; do not over-compress the material
• Keep insulation clear of vents, heating elements, fans, and moving parts

This suspension damper stabilizes the tub/drum by absorbing movement and vibration during operation. Replacing a worn damper helps reduce shaking and noise, improving spin performance and overall machine stability. What it does:

• Absorbs and controls tub/drum movement to reduce vibration and noise
• Helps prevent banging, "walking," or out-of-balance shutdowns during spin
• Can address excessive shaking, rattling, and longer spin times
• Restores smoother, more controlled operation when the original damper is worn

• One suspension damper

• Disconnect power and turn off water supply before servicing
• Access location varies by model; support the tub/drum to relieve load before removal
• Note orientation and reuse existing mounting hardware if new fasteners aren't provided
• After installation, re-level the appliance and run a test cycle to verify stability

This overflow component directs excess water safely back into the dishwasher's water path to help prevent overfilling and leaks. Replace if damaged to restore correct water management and leak protection.

• Guides overflow water away from the tub into the proper return/drain path
• Helps maintain correct water level during fill
• Can address water collecting in the base pan or leaking from the lower front area
• Useful when the leak protection/float has been tripped or cycles stop due to a detected leak

• Disconnect power and turn off the water supply before servicing
• Access the overflow/water-channel area per your model's service procedure
• Note orientation and transfer any clips or seals from the old part if present
• Reassemble, restore power/water, and run a short cycle to check for leaks

This cable harness routes power and control signals between the appliance's control and its components. Replacing a damaged harness restores solid electrical connections so the unit starts, runs, and completes cycles without intermittent failures or non-working functions. What it does:

• Distributes electrical power and control signals between boards, motors, valves, and sensors
• Replaces wiring that is burnt, brittle, frayed, or corroded
• Helps resolve symptoms like won't start, intermittent operation, inoperative features, or error/fault indications related to open/shorted circuits
• Restores safe, reliable connectivity to prevent further electrical damage

• 1 cable harness assembly

• Disconnect power at the breaker or unplug the appliance before servicing
• Photograph/label connections and routing to match the original layout
• Seat connectors fully by the housings; do not pull on wires
• Route and secure away from sharp edges, moving parts, and hot surfaces to avoid chafing or heat damage

This holder/retainer secures its mating part in the correct position inside the appliance, preventing unwanted movement and ensuring consistent operation. Replace a cracked or missing holder to restore a solid, factory fit and reliable performance.

• Supports and locks the attached component or rack/accessory in place
• Helps prevent vibration, rattling, or misalignment during use
• Typical signs of failure: broken tabs, visible cracks, looseness, or the part no longer staying secured
• Restores proper positioning of the related component for consistent function

• Disconnect power at the breaker; shut off water supply if applicable
• Note the holder's orientation; take a photo before removal
• Reuse existing screws/fasteners if none are supplied with the part
• Seat fully until it clicks/locks; do not overtighten into plastic

This cable harness routes power and signals between appliance control and components to restore reliable electrical connections. It replaces a damaged or worn harness to help eliminate intermittent operation and connectivity issues. What it does:

• Replaces the main wiring harness that links controls, sensors, and motors for proper electrical communication
• Restores reliable power and signal paths to correct intermittent power, non-responsive controls, or components that won't run
• Ensures secure connector mating to prevent arcing and poor contact
• Matches OEM connector types and wire lengths to fit in the original routing

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock
• Compare the new harness to the old one for connector types and routing before installation
• Handle connectors by the housings; do not pull on wires. Ensure all plugs snap fully into place

This is a replacement screw used to secure panels, trim pieces, and small brackets on compatible Bosch appliances — a simple hardware fix that restores proper fit and stops rattling or loose parts. What it does:

• Fastens outer panels, control bezels, or internal brackets to the appliance chassis
• Keeps panels aligned so doors and controls fit and operate correctly
• Stops vibration noise caused by loose or missing fasteners
• Replaces damaged, stripped, or corroded screws

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Thread by hand to start, then snug; avoid over-tightening which can strip threads or crack panels
• If threads are damaged, replace the mating nut or threaded insert per OEM guidance

This repair kit restores the pump sump area on compatible Bosch dishwashers, helping stop leaks and restore proper water flow. Use it to replace worn sump components without replacing the entire pump assembly. What it does:

• Replaces worn pump-sump components that can cause leaks or allow water to pool in the dishwasher sump.
• Restores sealing and impeller engagement to help the drain and circulation pumps move water effectively.
• Can stop symptoms like water remaining in the tub, unusual pump noise, or visible leaks around the sump area.

• Disconnect power and water supply before starting any repair.
• Inspect removed parts and mating surfaces for damage; replace the full pump assembly if housings are cracked.
• Follow manufacturer instructions for proper seal and impeller seating; test for leaks and correct operation after reassembly.