Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement power cord that connects your washer to the wall outlet. Includes strain relief for cable protection. Needed when original cord is damaged, pinched, shorted, or worn. Direct plug-in installation.
Bought a new cord and removed the back of the washer and unclipped the old and clipped in the new. 5 minutes tops. Read more
Secures the door boot seal on front load washers to prevent water leaks. Replace if seal is loose or water seeps during wash cycles. Confirm fit with your model.
Im not a repairman, so all my knowledge to fix my washer came from either youtube or online chats. I posted this to help the next dad trying to save a few bucks. Door sensor... Since door sensor worked correctly, verified that by starting washer with door open, and agitate cycle would not start until door was closed. Meaning door sensor worked correctly. Timer... In high spin cycle washer sounded correcltly spinning, but when opening door, drum was was not moving. So timer was triggering... Read more
Fixes agitator that won't move or spins slowly. This upper agitator section restores proper wash action when teeth strip or wear. 10-minute repair.
I replaced the thrust washer , agitator and agitator dog assembly. The repair took about 10 mins after watching the repair video. All works fine. Mike C Read more
Secures the motor to its mounting point in your laundry center. Replace if the retainer is worn, broken, or has lost tension to prevent motor misalignment.
Replaced with new retainer clips and new capacitor to fix future problems Read more
Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.
Replaced clutch assembly which was a little tricky, but very doable. Just make sure to take your time. I do have to say that I am very impressed with AppliancePartsPro customer service when the replacement part also failed. A new clutch assembly was at my door step a few days later. I now has a working washer again. Thanks Again Appliance Parts Pro. Read more
Replace a cracked, broken, or worn washer timer dial. Sits behind the knob with gray indicator to select cycles. Essential cosmetic component.
Watched the video and completed repair as shown Read more
Push-in nut for washers. Secures components and panels inside the cabinet. Replace if cracked, broken, or missing to restore proper assembly.
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair... Read more
Secures hose connections to prevent leaks in your washer. Replace if you notice dripping at hose fittings or loose connections. Verify fit with your model.
Took off cover, installed new parts. Read more
Fix a washer that won't agitate or spin due to a faulty lid switch. This mounting screw secures the lid switch assembly. Simple 1-hour DIY repair.
Replaced the water inlet valve. Read more
Fix a burnt or melted lid switch connector causing your washer to be completely dead. This terminal receptacle restores power to the lid switch.
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!) Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts... Read more
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
Replace your washer's anti-rattle clip to eliminate vibration noise and buzzing during cycles. Secures components with light spring tension. Confirm fit with your model number before ordering.
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever. Read more
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Replaced with new part ordered from store Read more
Secures the rear bulkhead to the washer tub, reducing vibrations. Replace if damaged by water exposure, stripped threads, or rusted from age.
Springs were broken and back bracket was bent I replaced the bracket and all four Springs including the vertical one. I removed the cabinet as shown in the video. Then with a pair of vise grips's removed the springs one by one and replace them. The bracket was rusted And bent i used a quarter inch socket with a quarter inch ratchet to remove the screw. Due to the rust i used penetrating oil the screw. Read more
Fixes intermittent operation or no power issues caused by melted or cracked connector housing. Secures terminal connections in washer wiring harness.
10-16 x 5/8 inch mounting screw for washers and dryers. Replaces rusty, corroded, or broken screws that secure console panels and internal components.
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete. Read more