Tmh116xsd-7 Parts

Seal tape restores a tight seal around appliance doors and panels to help prevent air or moisture leaks and improve temperature stability. Use it to replace worn or missing sealing strips that allow drafts, frost, or heat loss. What it does

• Creates a flexible barrier to close small gaps and reduce airflow or moisture migration at door and panel seams.
• Helps maintain correct internal temperatures and can reduce frost buildup or inefficient cooling/heating.
• Replace when tape is cracked, compressed, detached, or visibly deteriorated.
• Commonly used where a thin, form-fitting sealing strip is needed on appliance doors and access panels.

• One seal tape.

• Clean and dry the mating surface before installing for best adhesion; remove old residue.
• Cut to fit and press firmly along the length to seat the tape; trim excess as needed.
• Disconnect power (unplug or switch off breaker) before starting.

This refrigerator water filter cartridge replaces the installed filter to help restore clear, better-tasting water and improve ice quality. It's a direct-fit replacement designed for compatible Whirlpool refrigeration systems. What it does:

• Filters water to reduce common impurities that can affect taste and clarity
• Helps improve the quality of ice produced by the refrigerator
• Can resolve symptoms like cloudy water, off-taste, or reduced water flow from the dispenser
• Restores proper filtration performance when the original filter is expired or clogged

• Follow the refrigerator manufacturer's instructions for removal and installation.
• Run and discard the recommended amount of water after installation to flush the system before use.
• Turn off the water supply and disconnect power if required by your model before servicing.
• Inspect the new filter for damage; do not use a damaged filter.

This capacitor stores and releases electrical energy to help an AC motor start and run smoothly. Replacing a weak or failed capacitor can restore reliable motor operation and reduce humming, no-start, or stall conditions.

• Provides the phase shift and starting torque an induction motor needs to start
• Helps the motor reach and maintain proper speed under load
• Common symptoms of a failing capacitor: motor hums but won't start, intermittent starts, slow or stalled rotation, or frequent thermal trips
• Visible clues may include a swollen case or leaking residue

• Disconnect power to the appliance before servicing; verify no voltage is present
• Capacitors can retain a charge—discharge safely before handling
• Note wire positions; move leads to the new capacitor one at a time and ensure snug terminal fit
• Reuse the original bracket/clip if applicable and secure the capacitor to prevent vibration

Screw that secures appliance panels and components to restore proper fit and reduce movement. Use this direct-replacement fastener to swap out stripped, missing, or damaged screws that cause loose panels or rattling. What it does:

• Secures panels, trim, brackets, and internal components to maintain alignment and prevent vibration.
• Replaces stripped, corroded, bent, or missing screws that can cause rattling, gaps, or loose parts.
• Restores proper fit and function of assemblies when original fasteners fail.
• Small part — confirm size and thread match your appliance before ordering.

• Disconnect power (and water, if applicable) before starting any repair.
• Use the correct screwdriver or bit; avoid overtightening to prevent stripping or cracking.
• Replace all like fasteners in the same area if multiple are damaged to ensure even fit and alignment.

This molded wire support clip secures wiring and small harnesses to the appliance cabinet or components to prevent rubbing, pinching, or contact with moving/heat-producing parts. It helps reduce chafing and electrical wear for safer, more reliable operation. What it does:

• Holds wiring harnesses and individual wires in place to prevent contact with sharp edges, motors, or heating elements
• Minimizes wire movement and vibration that can lead to chafing or broken conductors
• Helps maintain proper routing for consistent connections and component performance
• Commonly used where a small push-fit retainer is needed to secure low-voltage or signal wires

• One wire support clip as shown

• Disconnect power to the appliance before servicing to avoid shock or injury
• Push-fit installation: align clip over wire/harness and press into the mating hole or slot until it snaps in place; clip may require slight flexing
• Inspect surrounding wiring and routing for damage; replace any frayed or exposed wires before reassembly
• If the mounting hole or panel is damaged, use the correct replacement panel or a suitable repair to ensure a secure fit

This piston assembly restores the moving piston used in the appliance's fluid/valve system to help recover proper dispensing and motion. It replaces a worn or damaged piston so the affected function can operate as intended. What it does:

• Replaces the piston that moves inside a valve or dispenser to control fluid or airflow
• Restores proper actuation and sealing that can prevent drips or improper dispensing
• Commonly installed when symptoms include poor dispensing, leaks near the valve area, sticking motion, or unusual noises during operation
• Works as a direct-fit replacement where this OEM piston assembly is specified

• One piston assembly as shown

• Disconnect power (and water supply or gas, if applicable) before starting any repair
• Follow the appliance service manual and use appropriate tools; keep small fasteners and seals organized
• Inspect sealing surfaces and O-rings; replace damaged seals to ensure a leak-free install
• Test the appliance after installation to confirm correct operation

Size: 2.8 fl.oz tube. 748 non-corosive sealant.

This thermistor is a refrigerator temperature sensor that monitors internal air temperature so the control board can regulate cooling. Replaces a failed sensor to help restore accurate temperature readings and more consistent cooling. What it does:

• Senses internal refrigerator temperature and sends a variable resistance signal to the control board
• Helps the control system cycle the compressor and fans correctly for stable temperatures
• Commonly replaced when refrigerator runs too cold, too warm, or has irregular cooling cycles
• Can address temperature-error codes or defrost control issues when the sensor is faulty

• Disconnect power to the appliance before inspecting or replacing the sensor
• Handle the sensor and wiring harness carefully to avoid damage to the probe or connectors
• Install in the original sensor mounting location and secure wiring away from moving parts

This base is the appliance's lower cabinet section that supports internal components and helps stabilize the unit. It restores a solid foundation so the appliance sits level and protects internal parts from floor contact and debris. What it does:

• Provides structural support for the appliance's internal assemblies and controls
• Helps stabilize the unit and reduce excessive vibration or rocking
• Protects wiring, motors and other components from contact with the floor
• A damaged or cracked base can cause noisy operation, misalignment, or uneven sitting

• Disconnect power (and gas if applicable) before beginning any repair
• Follow the OEM service manual for disassembly and reassembly steps
• Replacement may require removing the cabinet and/or drum; having a second person helps with lifting and alignment
• Inspect and reuse original fasteners only if undamaged; replace any worn mounting hardware

This magnetron generates the microwave energy that heats food in a microwave oven. Replacing a failed magnetron restores normal cooking power and stops weak or no-heat performance. What it does:

• Converts high-voltage power into microwave radiation to heat food
• Restores full heating when poor or no heating is caused by a failed magnetron
• Addresses symptoms such as weak heating, no heating, or unusual humming/buzzing during operation
• Not a control board or transformer—this part is the microwave source component

• One magnetron (single unit)

• Disconnect power before servicing; microwave high-voltage components can hold a dangerous charge
• Handle the antenna/ceramic output carefully to avoid damage; inspect seals and waveguide components during replacement
• After installation, verify proper operation and safety features before normal use

This replacement screw is a general-purpose fastener used to secure exterior panels, trim, or internal components on compatible Whirlpool appliances. It restores proper fit and reduces rattles or loose parts for a safer, more reliable appliance. What it does:

• Secures panels, trim pieces, or mounting brackets to keep components in place
• Prevents vibration-related noise and movement caused by missing or loose fasteners
• Helps maintain alignment of control panels and exterior housings
• Replaces stripped, corroded, or lost screws to restore original fit

• Use the correct screwdriver or bit to avoid stripping the head
• Match screw length and thread engagement with the original for a secure fit
• Tighten to snug only; over-tightening can strip threads or crack panels
• Disconnect power before performing repairs on electrical components

This replacement power cord supplies electricity to the appliance so it can run safely and reliably. It replaces a worn, frayed or damaged cord to restore steady power and reduce risk of electrical problems. What it does:

• Delivers mains power from the outlet to the appliance's internal wiring
• Replaces cords with visible damage, exposed wires, or broken plug ends
• Stops intermittent power or complete loss of power caused by a damaged cord
• Helps prevent arcing and poor connections when original cord has failed

• Always disconnect power at the wall or breaker before inspecting or replacing the cord
• Secure the cord strain relief and ensure wire connections are tight and correctly routed