Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Secures control knobs onto shafts in top-load washers. Replace when knobs slip or fall off to restore proper fit and operation. Verify compatibility.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Cushions where the washer lid meets the top panel to soften closure and protect the finish. Replace worn, cracked, or missing bumpers to reduce noise.
The problem was most likely the evaporator fan motor but it could have been a bad blade, loose parts or bad motor mounts. Hard to tell without taking everything apart and inspecting. Since fridge was 17 years old I decided to order the entire evaporator fan assembly as shown in the parts diagram including fan blade, motor brackets, motor, motor mounts, screws, etc. Getting to the assembly involved removing the ice maker unit plus the entire rear inside of the freezer section. Parts cost around... Read more
Adjustable leveling leg threads into washer base to stabilize cabinet and reduce vibration. Replace if cracked, broken, or missing for proper support.
Took the old leveling legs out and put the new ones in Read more
Secures the drive pulley to the transmission shaft in top-load washers. Replace if the original nut is backing off, stripped, or missing.
Plastic bushing that fits inside your washer's lid hinge for smooth pivoting. Replace if worn, cracked, or causing lid misalignment and squeaking.
Not hard when you have videos and a mechanical background....piece of cake.... Read more
12-pack of inlet hose washers for washers and washer dryer combos. Replace cracked, worn, or missing washers to prevent leaks at water connections.
I called on your service, a person on the phone name Mr.Berry ask what the matter was . I told him the said a water valve should fix it . it sure was the right fix. thank you guys and thank you Mr. Berry. john m Read more
Secures the drum mounting hub to the drive shaft in top-load washers. Replace if screw is stripped, corroded, or missing during hub repair work.
Replaced the hub nut, tub bearing split ring, tub seal, hub washer and agitator coupler. I watched multiple times the APP video. It was extremely helpful and I would not have attempted this without seeing the video. I had a lot of trouble getting the hub nut off. I used an 1 5/8" 6 point strike box wrench and a 4# hammer to get it off. I sprayed it with WD 40 5 or 6 times over of the course of a week to let it soak. I finally got it off. Had I known that the shaft is not round I would have... Read more
Replace missing or stripped mounting screws in your refrigerator. This 12-pack of 8-32 thread screws secures panels, brackets, and components.
Snap-in plastic clip cover that conceals fasteners and secures panels on your top-load washer. Replace if broken or missing to restore appearance.
Secures washer drum and internal components during transport to prevent movement and damage. Replace if missing, bent, or broken before moving your appliance.
Washer won't advance through cycles or timer dial doesn't respond? This mechanical timer restores timed operation and reliable cycle progression.
Replacement screw secures panels, brackets, and trim on washers, dryers, and refrigerators. Needed when original fasteners are stripped or missing.
Replacement mounting screw for refrigerators. Secures panels, brackets, and components. Needed when original screws are stripped, missing, or lost.
Alignment pin keeps washer door hinge positioned so the door closes evenly. Replace if cracked, bent, or missing to restore proper door fit and seal.
Replaced washer tub straps and a broken strap retaining clip. Read more
Replacement shelf support stud for refrigerator shelves. Installs to hold shelves in place. Needed when original stud is broken, cracked, or missing.
6-20 x 3/8 in. screw secures panels and brackets inside washers. Replaces missing, stripped, or damaged fasteners to restore proper fit and stability.