Wap24021uc/11 Parts

This front drum motor mounting bushing supports the dryer drum shaft and helps the drum spin smoothly for quiet, even drying. It replaces a worn bearing surface to reduce noise and prevent drum misalignment. What it does:

• Provides a low-friction bearing surface for the drum shaft at the front motor mount
• Helps keep the drum properly aligned during rotation
• Reduces squealing, grinding, or rubbing noises caused by a worn front bushing
• Prevents excess wear on the drum shaft and adjacent components when functioning correctly

• One front drum motor mounting bushing

• Disconnect power before beginning any repair and follow all safety precautions
• Inspect the drum shaft, drum seal, and rear bushing for wear and replace as needed
• Use appropriate tools to remove the old bushing and press or seat the new bushing evenly
• Re-check installation and related components if alignment or noise persists after replacement

This operating module is the electronic control board that manages cycle selection and user-interface functions, helping restore normal operation and responsive controls to the appliance. What it does

• Controls and sequences appliance functions such as cycles, timers, and display feedback
• Interfaces with the user control panel to register button presses and selection changes
• Can resolve symptoms like unresponsive controls, incorrect cycle behavior, or error codes tied to the control electronics
• Works alongside sensors and power components to start and stop operations as commanded

• Always disconnect power to the appliance before beginning service to avoid shock and damage
• Handle the board carefully and avoid electrostatic discharge; use an anti-static strap if available
• Verify connector orientation and seating before restoring power; do not force connectors

This fastening ring secures and stabilizes a component assembly to maintain alignment and proper sealing. It's a direct-fit retaining ring used where a small stamped or formed clamp is required to hold parts in place. What it does:

• Holds a shaft, seal, or housing component in position to prevent movement or misalignment
• Helps maintain a consistent seal around gaskets or bearings to reduce leaks
• Prevents rattling or vibration by keeping mating parts tightly seated
• Restores proper component engagement that can stop intermittent operation or noise

• Use appropriate pliers or retaining-ring tools; avoid prying with screwdrivers
• Wear eye protection—rings can snap or release under tension

2 included - Front load

This hose inlet is the dishwasher water-connection fitting that routes incoming water into the appliance. It provides a secure connection to help prevent leaks and ensure consistent water supply for normal wash cycles. What it does:

• Connects the household water supply to the dishwasher's internal water system
• Seals the inlet to help prevent drips or leaks at the connection point
• Ensures the appliance receives steady water flow for proper filling and operation
• Be replaced when the inlet is cracked, corroded, or leaking

• Disconnect power and shut off the water supply before starting any work
• Inspect and replace any worn O-rings or gaskets when installing the new inlet
• Hand-tighten fittings and then check for leaks; retorque per OEM guidance if available

This holder is a replacement mounting bracket that secures a small internal component in place to restore proper alignment and support. It helps keep parts stable so the appliance operates as intended. What it does

• Secures and supports an internal component to prevent movement or misalignment
• Replaces cracked, broken, or worn mounting points that allow rattling or improper part position
• Restores stable contact where a loose component causes intermittent operation or noise
• Fits a specific OEM location; use the part number to confirm exact application

• One replacement holder/mounting bracket

• Disconnect power and water before starting any repairs
• Inspect surrounding clips or fasteners and reuse or replace as needed—this part typically snaps or screws into place
• Handle plastic mounting parts gently to avoid cracking during installation

Replacement holder that secures internal components and accessories, restoring proper fit and preventing movement or rattling. Direct-fit design replaces a worn, cracked or broken holder to keep parts stable during normal operation. What it does

• Secures panels, racks or small internal components in place to prevent shifting.
• Restores correct alignment when a broken holder allows parts to sag or detach.
• Eliminates rattling or vibration caused by loose or damaged mounts.
• Helps maintain proper operation by keeping components positioned as intended.

• Disconnect power (and water supply if applicable) before starting repair.
• Remove any obstructing panels or accessories to access the holder; keep track of fasteners.
• Install the new holder in the same orientation; snap or fasten it until it seats securely—do not force or overtighten.

This inner oven door window is the glass panel that restores clear visibility into the oven and protects internal components from heat and debris. Replacing a damaged or fogged window brings back a safe view of cooking without affecting oven operation. What it does:

• Provides a clear viewing surface so you can monitor food without opening the door
• Protects internal oven components from splatter and heat exposure
• Stops drafts and prevents further breakage when cracked or chipped
• Helps restore normal appearance when the glass is scratched, cloudy, or shattered

• Disconnect power to the appliance and allow the oven to cool completely before beginning
• Handle glass with heavy gloves and eye protection to avoid cuts
• Installation typically requires removing the oven door and a small number of screws or clips
• Use the exact part number to ensure correct fit; do not force glass into place

This genuine replacement motor powers the component it's coupled to, restoring reliable motion and performance. Installing a new one brings your appliance back to proper operation.

• Drives the attached mechanism to provide the force needed for movement or airflow
• Common failure symptoms: won't start or stalls, loud humming/grinding, vibration, overheating, or burning odor
• Restores proper operation and performance when the original motor is worn or failed
• Built to interface with the existing mounting and wiring on applicable models

• Disconnect power at the breaker or unplug the appliance; allow hot parts to cool
• Photograph wire routing and note terminal positions before removal
• Support the assembly during removal; transfer any brackets, wheels, or pulleys from the old motor as required
• After installation, spin the shaft by hand to ensure free movement and proper rotation/clearance before reassembly

This flexible water hose routes water between internal components in your appliance. Replacing a worn or cracked hose restores a sealed, reliable water path to help prevent leaks and water-flow issues.

• Directs water between assemblies to maintain proper flow
• Helps keep the water path watertight to avoid leaks
• Can resolve symptoms like slow/failed draining, pooling water, or visible drips
• Replaces hoses that are brittle, cracked, kinked, or clogged

• Disconnect power and shut off water supply before servicing
• Place towels or a pan to catch residual water; note original routing
• Move over and secure existing clamps/seals; avoid kinks during routing
• Run a test cycle and check all connections for leaks

A replacement drain hose that routes wastewater from the dishwasher tub to the household drain. Replacing a damaged or clogged drain hose restores proper draining, helps prevent standing water and reduces the risk of leaks. What it does:

• Channels wastewater from the dishwasher to the home drain so cycles can finish without leaving water in the tub.
• Provides a sealed path to prevent leaks under the appliance; cracks or splits can cause puddles or floor damage.
• Flexible routing helps avoid kinks and obstructions; a blocked or pinched hose can cause slow draining or drain-related error codes.

• Disconnect power and water supply before starting any work.
• Remove the lower access panel or toe kick to access the hose and note original routing before removal.
• Reconnect using the existing clamps or appropriate replacement clamps; ensure fittings are seated and secured to prevent leaks.
• Run a short drain cycle and inspect all connections and surrounding areas for leaks.

This replacement flap restores proper operation by sealing or guiding an opening within the appliance assembly. Replacing a damaged flap helps maintain correct movement and alignment, preventing nuisance rattles and performance issues in the related area. What it does:

• Covers or seals an opening, chute, or compartment to maintain proper function
• Guides airflow, water, or items as designed within the assembly
• Hinges/snaps to allow controlled opening and closing
• Typical failure symptoms: cracked or broken plastic, flap won't stay closed, poor sealing, noise or misalignment in the affected section

• 1 flap

• Disconnect power and, if applicable, shut off water before servicing
• Wear cut-resistant gloves; edges and surrounding metal/plastic may be sharp
• Note the original orientation and hardware; take a quick photo before removal
• After installation, verify the flap moves freely and seals/aligns as intended

This dispenser tray is the dishwasher detergent cup assembly that holds and releases detergent during wash cycles, helping ensure detergent is delivered when the machine rinses and cleans dishes. What it does

• Holds detergent/soap and releases it at the correct point in the wash cycle
• Ensures proper detergent flow to improve cleaning performance
• Prevents loose detergent from scattering inside the tub
• Visible replacement sign: cracked, warped, or detergent residue that won't clear

• One dispenser tray (detergent cup) as shown

• Disconnect power and water supply before removing or installing the dispenser
• Remove the inner door panel per manufacturer instructions to access the tray
• Handle carefully to avoid damaging the door latch and wiring harness
• Run a short test cycle after install to confirm proper operation and detergent release

This fixing kit supplies the mounting and fastening hardware used to secure appliance components during installation or repair, helping restore proper fit and reduce vibration or loose panels. Ideal for replacing missing or damaged fasteners. What it does

• Provides the specific screws, clips, and brackets used to anchor panels or assemblies
• Stops rattling and vibration caused by loose or missing mounting hardware
• Restores proper alignment of doors, panels, or internal components
• Replaces worn or corroded fasteners that can compromise a secure fit

• Disconnect power and water before beginning any repair work
• Use proper tools and follow the appliance manufacturer's installation instructions
• Inspect surrounding components and mounting surfaces; replace any damaged parts