Wd31x1004 Parts

This inlet hose is the internal water line for your dishwasher, routing fresh water from the fill valve into the wash system. Replacing a brittle or leaking hose restores reliable filling and helps protect floors and cabinetry from water damage.

• Channels incoming water from the inlet valve to the tub/sump
• Maintains proper fill level and flow at the start of each cycle
• A cracked, kinked, or loose hose can cause leaks or slow/no fill
• Restores correct water delivery and helps prevent water damage

• Disconnect power and shut off the water supply before servicing
• Pull the dishwasher forward for access; place a towel or pan to catch residual water
• Note the original routing and clamp positions; transfer clamps and avoid kinks
• Restore water, run a quick fill cycle, and check all connections for leaks

This rotor position sensor (Hall sensor) tracks the direct-drive motor's rotor position and speed so the control can commutate the washer motor accurately. Replacing a failed sensor can restore proper wash/agitate and spin performance. What it does:

• Detects rotor position and speed from the stator assembly
• Sends timing feedback to the control for correct motor start, direction, and speed
• Supports smooth agitation and spin ramp-up/ramp-down
• Failure may cause: no spin or agitation, cycle stalling/pausing, or an LE motor error code

• 1 rotor position sensor assembly

• Unplug the washer and shut off water; wear protective gloves
• Access the motor at the rear of the tub; remove the back panel if needed
• Remove the rotor and stator; support the stator to protect wiring, then unclip/unscrew and replace the sensor
• Align the sensor correctly and seat the connector fully before reassembly and testing

This base bracket mounts to the washer's lower frame to hold associated components securely in place. By keeping parts properly anchored, it helps maintain alignment and stability during operation to minimize vibration and noise.

• Attaches to the washer base and provides a mounting point for designated hardware
• Helps keep assemblies from shifting during agitation and spin
• Supports smooth, quieter operation by reducing vibration and rattling
• Common signs of failure include a bent or cracked bracket, loose/misaligned parts, or unusual noises from the base area

• Disconnect power and water supply before servicing; move the appliance for safe access
• Carefully tip or lay the washer back on protective padding; use a helper for stability
• Note the bracket's orientation and reuse existing mounting hardware as applicable
• Tighten fasteners securely and verify nearby parts have proper clearance before test run

This stator assembly is the stationary motor coil that produces the magnetic field to drive the washer motor. Replaces a worn or damaged stator to restore magnetic coupling between the motor and rotor for normal drum movement. What it does:

• Generates the magnetic field the rotor uses to spin the drum
• Restores normal spin and agitation when a failed stator causes no-spin, weak spin, or humming
• Works with the washer's rotor/drive components as part of the motor assembly
• Handles the electrical and magnetic interface; must match motor/rotor configuration

• One stator assembly

• Disconnect power and water before servicing; use proper lockout procedures
• May require removal of the motor/rotor and housing to access the stator
• Inspect rotor magnets, bearings, and wiring for related damage while replacing

This spring-style hose clamp secures a washer's rubber hose to its fitting to maintain a tight, leak-resistant seal. Replacing a weakened clamp helps stop drips and keeps the hose firmly in place during operation.

• Provides constant spring tension to hold a rubber hose on its port
• Helps prevent leaks at the connection point
• Resists vibration so the hose doesn't back off the fitting
• Common signs include water at a hose joint, a loose/detached hose, or a rusted/broken clamp

• Disconnect power and turn off water supply before servicing
• Place a towel or pan to catch residual water from hoses
• Use pliers to compress the ears, slide off the old clamp, position the new clamp behind the hose bead, and release evenly
• After reassembly, run a quick test cycle and check for leaks

Locking pin for shock absorber.

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

The Control Unit is an OEM part for Bosch warming drawers. As the central hub, it regulates all functions including temperature settings, timers, and indicator lights. Working seamlessly with internal components, the control unit facilitates precise warming performance.

Symptoms of a bad control unit include:

• Inability to turn on or adjust the temperature 
• Preset warming functions not engaging
• Lights remaining dark or blinking erratically
• Frequent error codes appearing

Causes of failure relate to water or moisture damage over time, power surges affecting electronic parts, as well as general component wear. 

This Bosch control unit replacement restores full functionality. It is also compatible with some Thermador and Gaggenau models. Ensure your warming drawer operates precisely with this reliable OEM part.

This drawer heating element is the replacement heating component for warming/serving drawers, restoring the drawer's ability to gently heat and hold food at serving temperatures. It fits into the drawer cavity and connects to the drawer's power circuit. What it does:

• Heats the warming drawer to maintain food temperature for serving
• Restores normal warming function when a drawer no longer heats
• Helps resolve symptoms such as no heat from the drawer or uneven/weak warming
• Works as the drawer's primary heating component in the warming/serving assembly

• One drawer heating element

• Disconnect power to the appliance before servicing to avoid shock
• Remove the warming drawer and any trim/panels to access the element
• Inspect wiring and connectors; replace only with matching OEM part number

This shaped handle cap covers and finishes the end of an appliance door or handle for a clean, finished appearance and to protect the handle end from damage. It restores the original look and helps keep dirt out of the handle cavity. What it does:

• Covers the exposed end of a door or drawer handle for a finished appearance
• Protects the handle end from chips, scratches, and grime
• Helps stop drafts or moisture intrusion into handle cavities
• Replaces missing, cracked, or broken handle end caps

• Typically snaps or slides into place; a small flat screwdriver or trim tool may help with removal/installation
• Work carefully to avoid scratching surrounding surfaces
• If the handle or surrounding trim must be removed, follow the appliance manufacturer's disassembly instructions first
• For appliances with electrical components near the handle, disconnect power before servicing

The washer Hose Retainer Holder Clip is an OEM part that mounts behind the control panel on LG front-loading washers. It positions water supply hoses to prevent kinks or stress that leads to leaks over time. 

Causes of a failed clip include fatigue from years of front-load vibration and damage from any installation or repair work behind the control panel.

Symptoms of an insufficient hose retainer clip include:

• Loose, misrouted, or flopping hoses behind the control panel
• Bulging or kinked hoses that restrict water flow
• Water leaks at hose connections

This OEM replacement clip is compatible with select Kenmore front-loaders.