Wdsr20804wn Parts

Outer tub cover kit that replaces a cracked or missing washer tub cover, protecting the inner tub and helping stop rubbing, noise and fabric snags. Restores proper tub clearance for smoother drum movement and quieter operation. What it does:

• Covers the outer wash tub to protect the inner tub and fasteners from contact and wear
• Helps stop rubbing, scraping or thumping sounds caused by tub-to-tub contact
• Reduces the chance of clothes catching between the inner and outer tubs
• Restores correct tub spacing so the drum spins without interference

• Disconnect power and water supply before starting any repair
• Access may require removing the agitator or inner tub and using basic hand tools
• Inspect mounting clips, seals and surrounding components and replace any damaged items
• Test the washer on a short cycle after installation to ensure proper fit and quiet operation

This power line filter sits between household AC and the washer's internal wiring to reduce electrical interference and help stabilize control operation. Replacing a failed filter may restore power and prevent nuisance breaker or GFCI trips.

• Filters incoming AC power to reduce electromagnetic interference reaching the control and motor circuits
• Helps prevent interference-related issues like erratic controls or random resets
• Failure may present as no power/blank display, intermittent power loss, or tripping a breaker/GFCI
• Visual clues of failure can include scorching, swelling, or a cracked housing

• Unplug the washer or switch off the circuit breaker before servicing; allow a few minutes for internal components to discharge
• Access the filter location (often near the control area or rear panel) per your model's service information
• Note wire locations (LINE, LOAD, and GROUND) and move one lead at a time to avoid miswiring
• Mount securely and ensure the ground connection to the cabinet is tight for proper operation

This small bushing fits the washer's lid hinge to provide a smooth, stable pivot. Replacing a worn hinge bushing restores proper lid alignment and helps reduce squeaks, rubbing, or excessive play when opening and closing the lid. What it does:

• Acts as a low-friction sleeve between the hinge pin and bracket
• Supports smooth lid movement and helps maintain alignment
• Reduces metal-on-metal wear and hinge noise
• Symptoms of wear can include squeaking, binding, scraping, or a loose/wobbly lid

• 1 hinge bushing

• Disconnect power before servicing
• Support the lid to prevent it from dropping when the hinge is loosened
• Remove hinge hardware to access and swap the bushing; reassemble and check lid alignment
• Many models use a bushing on each hinge—inspect both sides and replace as needed

Secure your washer's drain hose with this drain hose strap. It keeps the hose positioned at the standpipe or laundry tub, helping prevent movement, dislodging, and messy leaks when vibration increases during drain and spin cycles.

• Secures the drain hose to a standpipe or utility sink, per installation guidelines
• Helps prevent the hose from backing out or spraying water during operation
• Reduces strain and kinking by keeping the hose routed in place
• Replaces a missing, cracked, or broken strap

• Unplug the washer and turn off water supply before starting
• Position the drain hose in the standpipe or tub and tighten the strap to secure it without kinking the hose
• Maintain the manufacturer-recommended air gap and hose height per your installation manual
• Run a quick drain/spin to ensure the hose stays secured and there are no leaks

Size: 14-10 a trt 7/8 s.

This 2-speed clutchless motor replaces the washer's drive motor to restore agitation and spin without a mechanical clutch. It provides the two common drive speeds used for agitate and spin cycles on compatible top-load washers. What it does:

• Turns the washer tub/agitation mechanism to enable agitate and spin functions
• Operates at two speeds (agitate and spin) using an internal clutchless design
• Commonly used when a washer hums, runs but won't agitate or spin, or fails to change between agitate and spin
• Works with the existing mounting bracket and wiring harness on compatible models

• Disconnect power before servicing to avoid shock or injury
• Motor is heavy and may require lifting assistance; support the tub during removal/installation
• Reuse the existing mounting hardware and wiring harness
• Follow the washer's service manual for disassembly, torque, and wiring routing; test operation before reassembling the cabinet

Single-speed PSC motor that restores rotational drive to the appliance. Replaces a worn or failing motor to stop humming, no-spin or intermittent operation and helps return steady rotation when the rest of the drive system is serviceable. What it does:

• Converts electrical power into mechanical rotation to drive the appliance's rotating components.
• Common signs a motor needs replacement: humming, no rotation, slow or intermittent rotation, or unusual motor smells.
• Replaces a failed motor to restore normal, consistent rotation when the motor is the root cause.
• Designed for direct replacement where the same mounting and wiring are used.

• Always disconnect power to the appliance before beginning service.
• Follow the appliance service manual and wiring diagrams; label or photograph connections before removal.
• Support drum/assembly as required when removing or installing the motor; avoid strain on wiring.

This clip cover is a small snap-in plastic trim piece that protects and secures appliance panels or trim, giving a finished look and hiding fasteners. Replaces broken or missing covers to restore appearance and retention. What it does:

• Snaps into place to conceal screws or clip anchors on trim and panels
• Helps hold lightweight trim pieces securely to the cabinet or frame
• Prevents exposed fasteners and reduces snagging or sharp edges
• Useful when cracked, worn or lost covers cause loose or rattling trim

• One clip cover

• Disconnect power or unplug the appliance before accessing panels or trim
• Push the clip cover onto the mating clip or anchor until it snaps fully into place
• Use a small flat tool only to remove; avoid prying on surrounding trim to prevent damage
• Replace any damaged mounting clips before installing the cover for a secure fit

8-18 hi/lo 5/8

Size: 8-32 t. Includes 12 screws.

Size: 8-18 ab.

This hex nut overmold assembly secures appliance components while the molded sleeve protects surrounding surfaces and reduces vibration. It replaces worn or missing fasteners to restore a secure fit and help prevent rattling or movement. What it does:

• Provides a threaded fastening point for panels, trim, or internal brackets
• Molded overmold sleeve protects finishes and helps isolate vibration
• Restores secure mounting when a nut is stripped, missing, or loose
• Helps reduce rattling and movement of attached parts

• Disconnect power and follow appliance-specific safety procedures before starting
• Tighten by hand then snug with the appropriate wrench; avoid overtightening to prevent damaging the molded sleeve

This dial assembly replaces a worn, cracked, or missing rotary control dial and restores a clear, tactile control for selecting settings. It provides a direct, user-facing interface so you can change cycles, temperatures, or power levels with confidence. What it does:

• Replaces a damaged or broken dial so the control knob turns smoothly and stays in position
• Restores the pointer/indicator used to select settings on the control panel
• Helps resolve symptoms like a loose, cracked, missing, or hard-to-turn dial
• Works as the user interface component that transmits rotation to the underlying control mechanism

• One dial assembly

• Disconnect power or unplug the appliance before beginning work
• Remove the existing dial by pulling straight off or following the appliance disassembly steps for your model
• Handle the new dial carefully to avoid scratching or damaging the indicator surface

A single replacement screw used to secure appliance panels, trim, and internal brackets so components stay aligned and reduce rattling. Simple, direct-fit fastener for restoring proper mounting and stable operation. What it does:

• Secures panels, mounting brackets, trim pieces and other appliance components
• Helps stop rattling, vibration, or loose panels caused by missing or stripped fasteners
• Restores proper alignment of doors and access panels when original screw is lost or damaged
• Matches the OEM fastening point for a straightforward hardware replacement

• Disconnect power to the appliance before working on electrical components or access panels
• Use the correct screwdriver to avoid stripping the head; match drive type to the screw
• Tighten firmly but do not overtighten—stop when snug to avoid damaging threads or parts
• Keep removed fasteners organized and compare with the replacement to ensure correct fit

This shipping bar assembly secures the oven door and internal components during transport to prevent movement and damage. Replacing a damaged or missing shipping bar helps ensure the range or oven door stays protected while moving the appliance. What it does:

• Holds the oven door and internal parts in place during shipment to reduce jostling and impact
• Prevents door misalignment or damage caused by transit
• Helps avoid rattling or loose parts after relocation
• Used only for transport/protection; remove before regular appliance operation if instructed by manufacturer

• One shipping bar assembly

• Intended for use during shipping/transport — confirm removal instructions in your owner's manual before operating the appliance
• Install or remove with the appliance powered off and according to manufacturer guidance
• Keep small fasteners and clips secure; replace any missing hardware with OEM-specified parts

This is a 8-18 x 1/2 inch hex washer head screw used to secure appliance panels and components. It provides a reliable, corrosion-resistant fastener for repair or reassembly tasks. What it does:

• Fastens panels, brackets or trim where an 8-18 x 1/2" screw is specified
• Hex washer head offers wider bearing surface to prevent pull-through
• Stainless finish resists rust and corrosion in humid appliance environments
• Restores proper fit and function when original screw is missing or damaged

• One 8-18 x 1/2 in. hex washer head stainless screw

• Use the correct driver/socket to avoid stripping the head
• Tighten securely but avoid over-torquing to prevent damage to plastic or thin metal parts
• Disconnect power and follow appliance safety precautions before working inside the unit
• Replace only with the same size and head style for proper fit