Wdsr20804wn Parts

This apron kit is used to convert the older 3 piece support apron to the new one piece apron. Kit includes: one piece rod support apron, spring clips, nut and bracket assembly, conduit, wire ties and instruction sheet.

The Wire Tie is an OEM part for GE dryers. It is used to secure and organize internal wiring, ensuring that wires remain properly positioned and do not interfere with the operation of the dryer. This part plays an important role in preventing wires from becoming tangled, pinched, or damaged during the dryer’s cycles.

Over time, the wire tie can become worn out, broken, or damaged due to prolonged exposure to heat, vibrations, or wear from normal use. A compromised wire tie can lead to loose or unsecured wiring, which may impact the performance of the dryer or cause electrical issues.

Symptoms of a bad Dryer Wire Tie include:

• Loose or unsecured internal wiring
• Interference with dryer components during operation
• Electrical malfunctions or short circuits
• Wires appearing frayed or damaged due to improper support

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

This tub clamp secures the washer tub or associated hoses to keep components aligned and sealed during operation. It replaces a worn or broken clamp to reduce movement and help prevent leaks and noise. What it does:

• Holds the tub/hose connection or tub assembly parts together to maintain a tight fit
• Helps prevent leaks caused by loose or damaged clamps
• Reduces rubbing, vibration, and associated noise from a loose tub assembly
• Restores proper component alignment after clamp failure

• Disconnect power and turn off water supply before starting any repair
• Inspect mating parts (tub, hoses, mounting points) for damage and clean before installing
• Use appropriate clamp pliers or screwdriver as required; ensure clamp is seated and tightened evenly

5/16-18 tpt ihw s n

A small push-in plug button used to fill or cover an access hole or trim opening and restore a finished appearance. Designed to snap into place for a secure fit and to keep dirt and moisture out. What it does:

• Covers unused holes or fastener openings to restore a finished look
• Helps keep dirt, moisture, and debris from entering cavities
• Holds trim or panels flush by filling gaps where a fastener or post is missing
• Commonly replaced when cracked, lost, loose, or causing rattles or gaps

• One plug button

• Disconnect power to the appliance before accessing panels or trim
• Typically snaps into place—press firmly until seated; may require removing trim for access
• Avoid prying with sharp tools that can damage surrounding surfaces
• Replace only with the exact part number to ensure proper fit and finish

This right-side end cap is a replacement trim/closure piece designed for the washer cabinet to restore proper fit and finish and help keep internals protected from debris. It replaces a damaged, cracked or missing end cap. What it does:

• Covers and protects the washer's right-side edge or mounting area from dust and moisture
• Restores a flush appearance where the original end cap was cracked or broken
• Helps prevent snagging on clothing or towels from a damaged trim piece
• Can reduce rattles or vibration caused by a loose or missing end cap

• Disconnect power to the appliance before beginning any work
• Usually secured with screws or clips; basic hand tools are typically all that's required
• Align the part to the right-side mounting location and fasten securely without over-tightening

This tub shield protects the washer's inner drum edge from wear and keeps clothing and items from catching on the tub lip. It helps reduce fabric snags and prevents damage to the drum opening during normal use. What it does:

• Covers the exposed edge of the inner tub to prevent garments from catching or tearing
• Protects the tub rim from chips, gouges, and wear that can lead to leaks or rough spots
• Helps keep the drum seal area smooth for consistent door/tub engagement
• Commonly replaced when you see fabric snags, visible tub edge damage, or persistent abrasion marks

• One tub shield

• Disconnect power and water supply before starting any repair
• Typically installs around the inner tub lip; may require drum rotation and simple fasteners or clips
• Inspect the tub rim and door seal while replacing the shield; replace damaged seals as needed

This front panel assembly replaces a cracked, worn or damaged console face to restore your appliance's appearance and support the control components. It provides the outer housing for buttons, displays and mounting points. What it does

• Covers and protects the control area from spills, dust and impact.
• Provides mounting locations and alignment for buttons, switches and display components.
• Restores a secure, finished surface when the original panel is cracked, warped or missing.
• Resolves cosmetic issues and loose or misaligned controls that affect operation.

• One panel front assembly.

• Disconnect power (unplug or switch off breaker) before starting any repair.
• Remove any trim, bezels or clips carefully to avoid damaging adjacent parts; keep fasteners for reinstallation.
• Handle edges and mounting tabs gently; some panels use plastic clips that can break if forced.
• If the control components or display must be transferred, note connector locations and orientation before disconnecting.

2 wire insulator.