Wed7ohebwo Parts

This Whirlpool Lint Screen is an OEM part for specific Whirlpool dryer models. This lint screen is essential for trapping lint and debris from clothes during the drying process, helping to prevent duct clogs and maintain efficient dryer operation. 

Lint screens can become less effective or damaged over time due to lint build-up, wear, or accidental tearing. A compromised lint screen can lead to reduced dryer efficiency, longer drying times, and increased risk of lint-related safety hazards.

Symptoms of a bad lint screen include:

• Visible tears or holes in the lint screen.
• Excessive lint accumulation on clothes after drying.
• The dryer takes longer than usual to dry clothes.
• Reduced airflow in the dryer, is noticeable during operation.
• Increased lint build-up inside the dryer duct.

This genuine Whirlpool OEM replacement part is compatible with Maytag, Jenn-Air, and Kenmore models.
 

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This lock secures the appliance's top panel to the front frame for a tight, stable cabinet. Replacing a worn lock restores a solid fit and helps eliminate rattles, gaps, and vibration during operation.

• Locks the top panel to the front panel to keep the top closed and secure
• Helps maintain cabinet alignment and rigidity
• Reduces movement that can cause vibration and rattling/squeaking noises
• Common symptoms: loose or popping top, visible gap at front edge, buzzing or clunking during cycles

• Disconnect power before servicing.
• Access the lock at the front edge where the top meets the front panel; remove the old lock and install the new one in the same orientation.
• Reuse original mounting hardware and ensure both sides are evenly aligned.
• Close the top and ensure a secure latch before restoring power.

This Dryer Repair Kit refreshes the tumble system by replacing the high-wear parts that cause noise and poor drum movement. Restore smooth, reliable operation and help extend the life of your dryer. What it does:

• Renews the drive path so the drum turns smoothly and consistently
• Restores proper belt tension and tracking with a new idler pulley
• Replaces worn or noisy drum support rollers to reduce squeaks and thumps
• Helps address symptoms like squealing/squeaking, rumbling/thumping, intermittent or no tumble, and burnt-rubber smells

• Kit includes: drum belt, idler pulley, and drum support rollers

• Disconnect power and shut off gas before servicing
• Access the drum per your model, support it when swapping rollers, and note the original belt routing
• Clean lint and roller shafts; do not lubricate rollers; route the new belt around the motor and idler as designed
• Spin the drum by hand to ensure smooth movement before reassembly and test run

• Replace all drum rollers at the same time to maintain even wear and quiet operation

Color: Grey

Fiberglass-reinforced door seal that restores an appliance door's airtight closure to help maintain consistent temperatures, reduce energy waste and minimize frost or moisture buildup around the door. What it does:

• Forms a continuous gasket around the door to keep cold air in and warm air out.
• Helps prevent frost buildup and uneven temperatures caused by air leaks.
• Common symptoms that indicate replacement: visible gaps, cold-air leakage, frost/ice at the door, or a door that won't seal flush.
• Fiberglass construction helps the seal retain shape for a more reliable long-term closure.

• Disconnect power to the appliance before beginning any service.
• Remove the old seal and clean the door channel; press the new seal evenly into place, checking for full contact around the perimeter.
• Some models may require partial door or liner removal—before disassembly.
• If the seal is stiff, follow OEM-recommended conditioning (allow to warm to room temperature or use manufacturer guidance) to help it seat properly.

Keep the drive system running smoothly. This idler pulley maintains proper belt tension and tracking so the drum/tub or drive system turns quietly and reliably, helping prevent squeal, slip, and premature belt wear. What it does

• Maintains constant tension on the drive belt to prevent slipping
• Guides the belt for smooth, consistent rotation of the drum/tub or drive system
• Helps reduce belt noise and premature belt wear
• Common symptoms of a worn pulley include squealing/scraping noises, burning rubber smell, the belt coming off or fraying, or no tumble/agitate/spin

• 1 idler pulley

• Disconnect power; turn off gas supply before servicing
• Access the belt path and note routing before removal
• Relieve belt tension, remove the old pulley, and install the new pulley in the same position; ensure the belt is seated on all pulleys
• Manually rotate the system to verify smooth operation before reassembly and testing

WPL VENT KIT, 4-WAY ULT

This replacement nut is a small hardware fastener used to secure components inside your appliance. It helps keep parts tight and properly aligned so assemblies don't loosen from vibration or normal operation.

• Threads onto a mating bolt, stud, or shaft to clamp parts together
• Maintains alignment and reduces movement and rattling
• Replaces a stripped, missing, or damaged nut to restore a secure fit
• Common signs of failure: loose panels or components, unusual vibration/noise, hardware missing

• Disconnect power; shut off gas and/or water if applicable before servicing
• Note the original hardware stack-up (washers/spacers) and orientation for reassembly
• Start by hand to avoid cross-threading; tighten to manufacturer guidance—do not overtighten
• Replace any damaged washers or locking devices

This replacement ice chute directs ice from the bucket to the dispenser opening, helping prevent jams and stray cubes. If the original chute is cracked, warped, or obstructed, replacing it restores smooth, consistent ice dispensing. What it does:

• Guides cubed or crushed ice through the dispenser opening into your glass
• Helps prevent ice from scattering or missing the glass
• Reduces ice jams and clogs caused by damaged or misaligned parts
• Common symptoms: ice not dispensing properly, ice spilling at the dispenser, frost or ice buildup in the chute area, broken plastic pieces

• 1 dispenser ice chute

• Unplug the refrigerator and turn off the water supply before servicing
• Access the dispenser area per your model's service instructions
• Note orientation; transfer any gaskets/seals and reuse original hardware if applicable
• Ensure the chute seats and aligns correctly with the ice door before reassembly and test

This push-button switch is the control-panel user-input switch that restores button responsiveness and reliable selection input. Replace a broken, stuck, or intermittently working button to regain normal front-panel control. What it does:

• Acts as the momentary push-button contact for the appliance control console.
• Replaces buttons that are physically cracked, stuck, or that fail to register presses.
• Helps stop intermittent or no-response conditions caused by worn or disconnected switches.
• Restores normal tactile feedback and electrical contact when the button is pressed.

• Disconnect power (unplug appliance or turn off circuit breaker) before attempting any repair.
• Access the control panel per your model's service instructions; handle sharp edges and fasteners carefully.
• Note wire connector orientation and secure all electrical connections before reassembly.
• Test the switch operation after reconnecting power and before completing reassembly.

A replacement front drum bulkhead that supports the dryer drum and helps keep the front bearing and seal aligned for smooth rotation. Use this bulkhead to restore proper drum alignment and reduce rubbing, noise, and excessive front play. What it does:

• Supports the front of the dryer drum and centers the front bearing/seal for stable rotation.
• Helps prevent drum rub, scraping noises, and uneven wear caused by a misaligned front support.
• Used when the front drum shows excessive play, thumping, or visible damage to the front support area.
• Installing a new bulkhead is commonly done alongside inspection of rollers, bearings, and the drive belt to ensure full drum stability.

• Disconnect electrical power (and shut off gas supply for gas dryers) before starting any service.
• Remove the front panel and drum to access the bulkhead; expect sharp edges and tensioned components—wear gloves and eye protection.
• Transfer any existing seals, bearings, or retainers only if undamaged; replace worn fasteners and inspect rollers/belts while the dryer is open.

This Lint Screen is an OEM part compatible with Whirlpool dryers. Designed specifically for Whirlpool models, this lint screen effectively captures lint and debris during the drying cycle, ensuring your dryer operates efficiently and safely. Its fine mesh construction is optimized for trapping even the smallest particles without obstructing airflow. 

A lint screen can become faulty due to wear and tear, overloading of the dryer, or improper maintenance. Accumulated lint or damage to the screen can reduce its effectiveness, potentially leading to longer drying times and increased energy consumption. 

Symptoms of a bad lint screen include:

• Reduced drying efficiency.
• Excessive lint accumulation on clothes.
• Longer than usual drying times.
• Unusual noises during the drying cycle.
• Visible damage or wear on the screen.

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.
 

Short baffle

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening

This motor mount clamp secures the dishwasher's pump/motor assembly to its housing, keeping the motor stable and the seal tight. Replace a damaged clamp to help prevent leaks and reduce vibration or rattling noise.

• Secures the pump/motor assembly at the mount to prevent movement
• Helps maintain a watertight seal at the motor connection
• A failed clamp can lead to leaking from the base area
• May cause excessive vibration or rattling during operation

• Disconnect power and turn off the water supply before servicing
• Access the pump/motor from beneath; support the assembly to relieve tension
• Note clamp orientation; ensure the existing seal is properly seated and tighten the new clamp evenly
• After reassembly, run a short cycle and check for leaks