Wfws400sw01 Parts

5 foot. Package of 2.

This washer control module is manufactured by Whirlpool. The washer control module handles all the functions, from filling to adjusting the cycle. Users enter their input through the interface controls, which sends the corresponding signal to the washer control module. Heat, moisture, and internal faults can compromise the module, though, potentially leaving the washer inoperable. Replacing the washer control module is not that involved. First, users should unplug the washer. Next, pull it out so there is ample room to access the rear of the appliance. Remove the back panel and the control module should be located on the left side. Disconnect the wiring from the module and remove the failed unit. Install the new one, reconnect the wiring, and then replace the back of the washer. Always wear gloves when working on household appliances.This is a genuine OEM part. It is designed to fit Whirlpool and Maytag washing machines. It is sold individually.

This genuine replacement part is a touchpad for washing machines. The touchpad is the main plastic piece where the buttons are located on the washer. Over time, a touchpad can become damaged and inoperable due to excessive wear and tear. If the washer buttons are no longer responding to commands, it could mean that it's time for a new touchpad. Thankfully, replacing the touchpad is fairly straightforward and is not too difficult of a repair.To replace the touchpad, make sure to unplug the washer. Once the power has been turned off, take a screwdriver to pry off the touchpad from its mounting tabs. Gently lift the touchpad out of its secured place. Once removed, take the new touchpad and snap it back into place.This OEM replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.

Push-in nut that secures panels, trim, or small components to studs or shafts. Restores a firm, vibration-resistant fastener to help stop loose panels and rattling caused by a worn or missing nut. What it does:

• Secures panels, trim or small assemblies to mounting studs or shafts.
• Helps keep parts aligned and reduces vibration or rattling during operation.
• Common symptom: loose or shifting panels, audible rattling, or components that won't stay in place.
• Designed for a push-fit installation to replace worn or missing fasteners.

• Always disconnect power to the appliance before servicing.
• Push the nut fully onto a clean, undamaged stud until seated; replace damaged studs or mounting hardware.
• If needed, use pliers or a socket to press the nut on evenly—avoid deforming surrounding plastic or sheet metal.

This inner door panel restores the washer lid's interior finish and structural support, helping the lid close and seal properly. It replaces a cracked, dented, or cosmetically damaged inner door to improve appearance and function. What it does:

• Provides the interior surface and mounting points for the washer top lid assembly
• Restores proper lid alignment and helps the lid close smoothly
• Eliminates sharp edges or cosmetic damage from a cracked or dented inner door
• Helps maintain correct fit with the outer door and lid components

• One inner door panel

• Disconnect power and water supply before starting any repair
• Remove the outer lid and related fasteners to access and replace the inner panel
• Keep track of screws and clips; hand-tighten fasteners to avoid stripping

This retainer is a small mounting clip that secures internal components in place to prevent shifting and noise during operation. It restores proper alignment so panels or assemblies stay fastened and stable. What it does

• Holds a panel, trim, or internal component securely in its mounting location
• Prevents rattling, vibration noise, and loose or sagging parts
• Keeps connected parts aligned for reliable operation
• Commonly replaced when clip is cracked, broken, or missing

• One retainer clip

• Disconnect power before starting any repair
• Remove necessary panels or access covers to reach the damaged clip
• Replace the clip in the same orientation; avoid forcing parts to prevent damage
• If additional fasteners are damaged or missing, replace them as needed for a secure installation

This name plate is the appliance identification label that displays model, serial and rating information and restores the unit's factory appearance. It helps ensure readable identification for service or resale. What it does

• Replaces a missing, faded or damaged identification label so model and serial info are visible.
• Provides required equipment ratings and manufacturer markings used during diagnostics and parts replacement.
• Restores exterior appearance where the original name plate is worn or peeling.
• Helps technicians and homeowners quickly confirm appliance identity during repairs.

• Name plate (single label)

• Disconnect power to the appliance before attempting installation or working near electrical connections.
• Clean and dry the mounting area; some name plates attach with adhesive while others fasten with screws—use the original hardware if present.
• Avoid bending or creasing the label when aligning it; press firmly to ensure full contact for adhesive-mounted plates.

This is a replacement screw used to secure panels and components on compatible Whirlpool appliances. It restores proper fit and reduces rattling or loose trim so doors, panels and controls sit securely. What it does:

• Secures panels, brackets or trim to the appliance cabinet
• Restores proper alignment and tightness where a missing or damaged screw causes looseness
• Helps eliminate vibrations and rattling caused by loose fasteners
• Matches OEM thread and head style for a proper fit in the intended mounting hole

• Use the matching screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Turn off power to the appliance before working near electrical components
• Replace any damaged or stripped mating hardware for a secure repair

The Noise Filter is an OEM part for Whirlpool washing machines. It absorbs vibrations and dampening sounds produced during agitation, spinning, and draining cycles. Located inside the unit, the noise filter helps contribute to a quieter washing experience.

Causes of a bad noise filter can be normal wear and tear over time, accumulated debris that hinders sound absorption, or physical damage to the noise filtering material.

Symptoms of a bad noise filter include:

• Excessively loud operation, even on lower cycles or speeds
• Strange rattling or buzzing noises coming from inside the washing machine
• Vibrations felt through the unit or nearby surfaces during operation

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This distributor assembly channels and evens out microwave energy inside the oven cavity so food heats more uniformly. It replaces a worn or damaged stirrer that can cause uneven cooking or noise. What it does:

• Rotates or disperses microwave energy to reduce hot and cold spots during cooking
• Restores proper energy distribution if the stirrer is cracked, warped, or missing
• Helps eliminate uneven heating, long cook times, or cold centers in food
• Supports normal operation of the microwave's internal waveguide system

• One distributor assembly (single complete stirrer/distributor piece)

• Disconnect power at the breaker or unplug the appliance before servicing
• Access may require removing the microwave cavity cover or control panel
• Handle the assembly carefully; avoid bending or cracking the blades or mounting tabs
• If other waveguide or mounting hardware is damaged, inspect and replace as needed

This top panel is the exterior upper cover that protects internal washer parts and gives the appliance a finished look. It restores a secure mounting surface for the control area and helps keep water and debris out of the cabinet. What it does

• Covers and protects internal components at the top of the washer cabinet.
• Provides the mounting surface and alignment for the control console and lid.
• Restores appearance when the original panel is dented, cracked, or rusted.
• Reduces rattles or vibration caused by a loose or warped top.

• Disconnect power and water supply before starting any repair.
• Use basic hand tools; some screws or clips may need to be removed to lift the old panel.
• Handle edges carefully — metal panels can be sharp.
• Have a second person assist if needed to prevent bending or dropping the panel.

This genuine-style drain hose routes wastewater from the tub to the drain pump to keep your appliance draining properly and reduce the risk of leaks or overflow. Designed to match OEM fit and routing. What it does:

• Carries wastewater from the tub to the drain pump or house drain.
• Prevents leaks by maintaining a sealed, flexible water path.
• Worn, cracked, or clogged hoses can cause poor draining, water on the floor, or error codes related to drainage.
• Replacing a damaged hose restores reliable drain performance.

• Disconnect power and turn off the water supply before starting work.
• Use original-style clamps or new hose clamps to ensure a secure seal; inspect fittings for damage.
• Avoid sharp bends or kinks when routing; confirm proper routing to prevent siphoning or backflow.

The Hose is an OEM part for Whirlpool washers.  

Causes of a bad hose can include wear and tear over time, exposure to excess heat and moisture, or accidental damage.

Symptoms of a bad hose include:

• Extended drying times or inability to fully dry clothes
• Visible cracks or splits allowing airflow issues
• Loose or disconnected ductwork connections
• Musty odors indicating trapped moisture

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The CORD POWER is an OEM part for Whirlpool washing machines. It serves as the connection between the washer and a power source, supplying electricity needed to run cycles and components. 

This power cord contains wiring designed to meet Whirlpool's rigorous safety and performance standards. It delivers steady voltage to power essential parts like the motor, timer module, and heating elements without interruption.

Symptoms of a bad power cord include:

• The washing machine not powering on when switched to a cycle 
• Cycles starting and stopping intermittently
• Surges in voltage resulting in errors or burned-out components
• An electrical burning smell coming from the cord 

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose is an OEM part for Whirlpool washing machines. As an integral part of the water inlet system, this reinforced rubber hose transports water from the home's supply lines into the washer. 

Symptoms of a bad hose can include:

• Leaks or drips from hose connections 
• Visible cracks or bulges in the rubber material
• Kinked or overly stiff hose that resists bending
• Water flow issues causing improper fill levels

Causes may relate to minerals/scale buildup weakening the hose over time, accidental cuts or punctures from improper handling, or flex fatigue from repetitive use. 

This Whirlpool replacement hose is constructed of durable rubber for years of leak-free service. It is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine brands.