Wgd7ohebw1 Parts

This wire harness routes power and control signals between a range of appliance components to restore proper electrical connections and reliable operation. It replaces a damaged or worn harness to help fix intermittent or complete loss of function. What it does:

• Connects control board, motors, switches and sensors so circuits complete and communicate
• Restores power and signal paths that cause intermittent runs, no-starts, or unresponsive controls
• Replaces frayed, burned, or broken wires and damaged connector ends
• Ensures correct routing to avoid pinched or chafed wiring that can lead to shorts

• Disconnect power (unplug or shut off breaker) before beginning any work
• Handle connectors gently; align pins before seating to avoid damage
• Route harness following OEM wire paths and secure with existing clips or ties
• Test appliance operation after installation and re-check connections for tight fit

This main wire harness routes power and signals between a washer or dryer's controls and components so the appliance can operate reliably. Replacing a damaged harness restores proper electrical connections and control response. What it does:

• Provides factory-style wiring and connectors between control board, switches, motors and sensors
• Restores lost or intermittent power and communication caused by frayed, burned, or disconnected wires
• Prevents short circuits and inconsistent operation from damaged harnesses
• Matches OEM connector types and routing for correct fit and function

• One main wire harness

• Disconnect power (unplug or shut off breaker) before starting any work
• Take photos of existing wiring and connector locations to ensure correct routing during reassembly
• Route the harness to avoid sharp edges, pinch points and moving parts; secure with clamps or ties as needed
• Inspect connectors and mating terminals for damage; replace if corroded or melted

This outer door assembly replaces a damaged or worn exterior door to restore the appliance's appearance and proper closure. It provides a durable replacement surface that helps keep the interior sealed and protected. What it does:

• Replaces cracked, dented, or cosmetically damaged outer door panels
• Restores proper door fit and helps maintain an effective interior seal
• Helps prevent drafts, moisture intrusion, and heat/cold loss related to a damaged exterior
• Matches OEM fit and mounting locations for straightforward replacement where applicable

• One outer door assembly

• Remove power and empty the appliance before starting; follow OEM service instructions
• Some installation steps may require removing trim, hinges, or internal panels—retain all fasteners
• Use proper tools and two people for alignment-heavy doors to avoid damage or injury

The Harness and Wiring Kit is an OEM part for Whirlpool dryers. It contains all necessary wiring and electrical components to facilitate communication between internal modules and overall appliance operation. 

Causes of a bad harness and wiring kit are typically due to cracking or wearing of insulation over many cycles exposing wires to potential shorts or damage. Normal movement during dryer tumbling can also damage wiring over time.

Symptoms of a bad harness and wiring kit include:

• Inoperative or intermittent cycles   
• Inability to select desired time or temperature settings
• Faulty temperature sensing inhibiting proper drying
• Random error codes or function failures  
• Exposed or loose wires near internal components

This authentic Whirlpool replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and Kenmore dryer models. 

The Overlay is an OEM part specifically designed for Whirlpool brand dryers. It provides protection and aesthetic finishing to the dryer door opening.

Causes of a bad overlay can include cracking or warping of heat-treated plastic material. Mineral buildup from vent ducts may also deteriorate painted surfaces over time.

Symptoms of a bad overlay include: 

• Peeling or chipped paint exposing underneath areas
• Cracks or fractures developing along edges and corners 
• Distortion compromising the proper fit around the opening rim

This replacement overlay directly replaces the worn original. Compatible dryer models are produced by brands such as KitchenAid, Maytag, Jenn-Air, Amana, and some Kenmore models. 

This shield is a molded protective cover that guards internal appliance components from moisture and debris, helping prevent damage and maintain reliable operation. It fits into place to keep nearby parts shielded and aligned. What it does:

• Covers and protects internal components from water, grease, and small debris
• Helps direct moisture away from sensitive parts to reduce corrosion risk
• Prevents rubbing and wear between adjacent parts that can cause noise
• Aids proper alignment and sealing of nearby panels and assemblies

• Disconnect power and water supply before beginning any repair
• Inspect mounting tabs and surrounding seals; replace any damaged fasteners
• Snap or screw the shield into the existing mounting points without forcing
• Replace those components before reassembly

This control panel is the exterior console trim that houses and protects your appliance's user controls and display, restoring a finished look and reliable button access. Ideal when the panel is cracked, faded, or cosmetically damaged. What it does:

• Protects and supports the appliance's buttons, dials, and display
• Provides the visible interface users interact with to select cycles and settings
• Restores legible labeling and a finished appearance to the console area
• Addresses symptoms like cracked or loose panel, worn graphics, or broken button mounts

• Disconnect power to the appliance before starting any work
• Remove screws or clips securing the old console; handle trim pieces gently to avoid damage
• Transfer any necessary switches or overlays per the service manual if applicable

This cable tie secures wiring and the power cord to the appliance chassis to help prevent chafing, pinching, or loose connections. Simple, low-cost part that restores proper wire routing and strain relief. What it does

• Holds wiring and harnesses in place to prevent rubbing against sharp edges
• Helps reduce risk of intermittent power or connector strain caused by loose wires
• Keeps harnesses routed for correct clearance and component access
• Useful during repairs to restore original wire routing and strain relief

• One cable tie (wire harness retainer)

• Safety first: disconnect the appliance from power before inspecting or replacing wiring components
• Remove the damaged or existing retainer and route harnesses to match original OEM routing before installing the new tie
• Trim excess tie tail; do not overtighten—secure, but avoid crushing wires
• Replace any tie that's melted, cracked, or otherwise damaged rather than reusing it

This rear bracket secures the dryer's rear panel and helps align internal components for stable operation. It restores proper fit and support when the original bracket is bent, broken, or missing. What it does:

• Secures and positions the dryer's rear panel to the cabinet frame
• Supports internal components and helps maintain proper panel alignment
• Prevents rattling, vibration, and panel separation during operation
• Helps ensure consistent airflow path by keeping the rear housing properly positioned

• Disconnect power (and gas, if applicable) before servicing the dryer
• Access typically requires removing the rear panel; keep fasteners organized for reassembly
• Inspect adjacent mounting points and replace any damaged screws or clips