Wgd92hefw Parts

A replacement front drum bulkhead that supports the dryer drum and helps keep the front bearing and seal aligned for smooth rotation. Use this bulkhead to restore proper drum alignment and reduce rubbing, noise, and excessive front play. What it does:

• Supports the front of the dryer drum and centers the front bearing/seal for stable rotation.
• Helps prevent drum rub, scraping noises, and uneven wear caused by a misaligned front support.
• Used when the front drum shows excessive play, thumping, or visible damage to the front support area.
• Installing a new bulkhead is commonly done alongside inspection of rollers, bearings, and the drive belt to ensure full drum stability.

• Disconnect electrical power (and shut off gas supply for gas dryers) before starting any service.
• Remove the front panel and drum to access the bulkhead; expect sharp edges and tensioned components—wear gloves and eye protection.
• Transfer any existing seals, bearings, or retainers only if undamaged; replace worn fasteners and inspect rollers/belts while the dryer is open.

This motor mount clamp secures the dishwasher's pump/motor assembly to its housing, keeping the motor stable and the seal tight. Replace a damaged clamp to help prevent leaks and reduce vibration or rattling noise.

• Secures the pump/motor assembly at the mount to prevent movement
• Helps maintain a watertight seal at the motor connection
• A failed clamp can lead to leaking from the base area
• May cause excessive vibration or rattling during operation

• Disconnect power and turn off the water supply before servicing
• Access the pump/motor from beneath; support the assembly to relieve tension
• Note clamp orientation; ensure the existing seal is properly seated and tighten the new clamp evenly
• After reassembly, run a short cycle and check for leaks

This factory fastener secures appliance components such as panels, brackets, and handles. Replacing a missing or damaged screw restores a tight fit, reduces rattles, and helps keep parts aligned for smooth, reliable operation.

• Secures components to the appliance frame or assemblies
• Helps maintain alignment and structural stability
• Replaces missing, rusted, or stripped hardware
• Common symptoms include loose/wobbly handles or panels, rattling/vibration noises, or a visibly missing screw

• Disconnect power before servicing
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten; snug until secure
• Replace any that are corroded or stripped for an even hold

The PAD is an OEM part crafted specifically for Whirlpool dryers. This pad plays a crucial role in the dryer's operation by providing support and cushioning for the dryer drum. Its precise design and compatibility ensure proper fitting and reduce noise during the drying cycles, contributing to smoother operation.

A worn-out or damaged dryer pad can lead to disruptions in the dryer's performance. Causes of a faulty pad might include wear over time, physical damage, or exposure to high heat, resulting in increased noise or imbalance during operation.

Symptoms of a bad PAD may include:

• Unusual or increased noise during dryer operation
• Visible signs of wear or deterioration on the pad
• Drum imbalance or wobbling during use

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This LP gas conversion label identifies that the appliance has been converted for use with liquid propane. Applying it near the gas valve/regulator clearly communicates fuel type for safe service, troubleshooting, and future installation decisions.

• Marks a converted unit as LP fuel to prevent misdiagnosis or incorrect hookups
• Provides quick visual identification for technicians and inspectors
• Replaces a missing, damaged, or illegible conversion label
• Use when a conversion has been completed and the original label is not present

• Apply only after completing the correct LP conversion procedure for your specific model
• Clean and dry the mounting surface; place the label where specified (typically near the gas valve/regulator or rating plate)
• Do not cover existing safety or rating labels; press firmly to ensure full adhesion
• Leak-check all fittings before returning the appliance to service

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Designed for use in dryers, the gas valve assembly is a part with solenoids or coils. These are used to close and open the valve that controls how much gas flows through the internal parts of the dryer. The gas valve assembly is made of strong materials but can become damaged or worn out. When this occurs, the dryer may not longer create heat during a cycle. If this happens, test the coils using a multimeter. If the reading is not within 1,000 to 2,000 ohms, the gas valve assembly should be replaced.Before starting, unplug the dryer from the wall and shut off the gas supply. Remove the lint screen from the housing and use a screwdriver to take out the screws in the housing. Disassemble the dryer to gain access to the gas valve and coils. Remove the screws from the mounting bracket to detach this part. Replace with the new component and test before use.The gas valve assembly is designed to be used with dryers by Kenmore, Maytag, and Amana. This genuine OEM part is directly sourced from the manufacturer. It is priced as a single unit.

This small nozzle directs the water stream cleanly into the ice maker during the fill cycle, helping prevent splashing and leaks so your unit produces consistent, properly sized ice cubes.

• Channels water from the fill tube into the ice maker's fill cup/mold
• Helps maintain correct fill volume and cube formation
• Reduces stray spray that can cause frost or ice buildup
• Typical symptoms: dripping from the fill tube, ice clumps below the ice maker, hollow/small cubes, or water on the freezer shelf

• Disconnect power and shut off the water supply before servicing
• Access the fill tube/ice maker area and remove the old nozzle
• Match the original orientation and seat the new nozzle fully
• Restore water and power, then run a fill cycle and check for leaks

The Thermistor is an OEM component specifically designed for Whirlpool gas dryers. It is a temperature-sensitive resistor that monitors the inlet gas temperature coming into the dryer. 

Causes can include the degradation of sensor components over time from repeated heating and cooling cycles. Moisture or debris intrusion could also impact functionality. 

Symptoms of a bad thermistor include:

• The dryer fails to progress through or complete cycles  
• Clothes remain damp even after extended drying
• Gas flow error codes are present
• Burned clothes smell is noticed from failed monitoring

This OEM Whirlpool replacement thermistor ensures accurate temperature readings for safe, optimized dryer operation. Its precise components deliver dependable sensing cycle after cycle. 

This part is also compatible with some GE, Crosley, Hotpoint, and select Kenmore electric and gas dryer models. Reliable and efficient drying performance results from an OEM thermistor replacement.

This factory fastener secures appliance components and panels, helping keep assemblies properly aligned and tight. Replace worn, stripped, or missing hardware to eliminate looseness and vibration and maintain safe, reliable operation.

• Fastens brackets, panels, trim, and internal assemblies to the cabinet/frame
• Helps maintain alignment of doors, consoles, or covers
• Restores a tight fit to reduce rattling, vibration, or shifting
• Common symptoms: missing screw, stripped head/threads, loose panel or handle, recurring vibration/noise

• Disconnect power (and shut off gas/water if applicable) before servicing
• Match thread and length to the original fastener for proper fit
• Start threading by hand to avoid cross-threading; use the correct driver
• Do not overtighten into plastic or thin sheet metal

This strike is the latch receiver the door or lid engages when closed. Replacing a worn or broken strike restores a secure close and ensures the control correctly senses a closed door so cycles can run. What it does:

• Provides the fixed catch point for the latch mechanism
• Keeps the door/lid closed and properly aligned during operation
• Works with the interlock/switch to signal that the door/lid is closed
• Common symptoms: door won't latch or pops open, "door/lid open" message, cycle won't start, visible damage to the strike

• 1 strike

• Disconnect electrical power to the appliance; shut off water if applicable
• Open the door/lid and remove the original strike (typically secured by screws or retaining tabs)
• Position and secure the new strike, reusing original hardware; tighten snugly without over-tightening
• Close and open the door/lid to confirm smooth latch engagement and alignment; adjust if needed

This small plug seals and finishes an unused factory or service hole on the appliance cabinet or liner. It restores a clean, finished appearance and helps keep dust and splashes out of the opening. What it does

• Closes an open hole on the cabinet/liner or panel
• Helps reduce entry of debris and incidental moisture into the opening
• Maintains a neat, finished look
• Replace if the original plug is missing, cracked, or won't stay seated

• 1 plug

• Disconnect power before servicing; shut off water supply if working near water lines
• Identify the correct opening per your model's parts diagram
• Remove any remnants of the old plug; clean the area
• Align and press the plug fully into the hole until it sits flush—do not force or deform the panel

The Valve is an OEM part for Whirlpool dryers. It is responsible for controlling the flow of water into the dryer's steam generator, enabling the steam function during the drying cycle.

A bad water inlet valve can occur due to wear and tear, sediment buildup, or malfunctioning internal components. If you notice symptoms such as no steam being produced during the drying cycle, insufficient steam generation, or water leakage around the valve, it may be time to replace this part.

Symptoms of a bad valve include:

• No steam being produced during the drying cycle
• Insufficient steam generation
• Water leakage around the valve

Restore your Whirlpool dryer by replacing the faulty or damaged steam water inlet valve with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This is the appliance's cabinet top panel in a chrome finish. It replaces a dented, bent, or rusted top to restore a clean appearance and a secure fit while protecting internal components and supporting mounted parts.

• Forms the finished top surface of the cabinet (chrome finish)
• Shields internal components from debris and accidental contact
• Provides mounting/support points for the console, hinges, or brackets (varies by model)
• Addresses damage, corrosion, looseness, or rattling from a bent or missing top

• Disconnect power before servicing; wear cut-resistant gloves (sheet-metal edges are sharp)
• Retain and reuse the original screws/clips; transfer any brackets from the old panel
• Fasteners are typically at the rear or beneath the console—support the panel, remove screws, then lift off
• Align the new panel and tighten fasteners evenly to ensure a secure, rattle-free fit

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

This precision-drilled burner orifice is sized for Type 4 butane applications. It meters gas to the burner so flames ignite reliably and burn cleanly when the appliance is configured for butane per the manufacturer's specifications. What it does:

• Regulates gas flow to the burner head for proper flame size and shape
• Type 4 drilling intended for butane gas configurations specified by the manufacturer
• Replaces a missing or stripped orifice during service or gas-type conversion

• 1 burner orifice (Type 4, butane)

• Shut off gas supply and power; allow the appliance to cool before service
• Access the orifice at the burner base/manifold; remove the original with the correct wrench or socket
• Start threads by hand; tighten snugly—avoid overtightening or cross-threading
• After reassembly, leak-check with soapy water and verify flame; gas conversions should be performed following OEM instructions and local codes