Wgtlv27hw Parts

This cabinet is the main outer housing that supports and protects the appliance's internal components while giving the unit its finished exterior. It restores structural integrity and proper panel alignment for safe, reliable operation. What it does:

• Provides the structural frame and mounting surface for controls, panels, and internal components
• Protects internal parts from dust, moisture, and incidental contact
• Helps maintain proper airflow and component positioning to reduce vibration and noise
• Restores correct panel alignment and closure when the original cabinet is dented, cracked, or corroded

• One cabinet

• Disconnect power (and gas, if applicable) before beginning any repair
• Installing may require removing trim, controls, and internal components; keep fasteners organized
• Use proper lifting technique and a second person for heavy or bulky cabinets to avoid damage or injury

This tub ring mounts at the top of the outer tub to contain splashes and suds during agitation and spin, helping prevent over-the-rim leaks. Replace a cracked or broken ring to restore proper water containment and fit.

• Acts as the upper splash shield for the outer tub
• Helps keep wash water and suds from escaping during operation
• Secures with locking tabs for a tight, even fit around the tub opening
• Typical signs of failure: cracks, broken/missing tabs, water or suds at the top of the tub

• Disconnect power and water; wear gloves and eye protection
• Lift or remove the top/console to access the tub opening
• Release retaining clips/tabs, remove the old ring, and clean the tub rim
• Align and snap the new ring evenly into place; confirm all tabs are fully seated before reassembly

This leveling foot threads into the base of your appliance to support and stabilize it. Adjusting the foot helps level the cabinet, reduce wobble and vibration, and keep doors aligned for smooth, reliable operation. Also called a leveling leg. What it does:

• Provides an adjustable contact point to stabilize the unit on the floor
• Helps level the cabinet so doors align and seal properly
• Reduces rocking, rattling, or excessive vibration on uneven surfaces
• Replaces a cracked, stripped, or missing leveling leg

• 1 leveling foot

• Unplug the appliance and turn off water supply if applicable
• Use a helper to carefully move or tilt the unit; support it securely
• Unthread the damaged foot; thread in the new foot by hand, then fine-adjust with a wrench
• Level side-to-side and front-to-back; ensure all feet make firm floor contact

The Lid is an OEM replacement part for Whirlpool washing machines. It is the top cover of the washer that provides access to the interior drum and tub, allowing you to load and unload laundry. The lid is designed to be durable and secure, ensuring safe and proper operation of the washing machine.

Symptoms of a bad Lid include:

• Difficulty opening or closing the lid
• Lid not closing or latching properly
• Visible cracks or damage to the lid material
• Lid becoming detached or falling off

Causes of a bad lid can range from physical damage due to impact or mishandling, to wear and tear over time from repeated use. Exposure to excessive moisture or humidity can also contribute to the degradation of the lid material or mounting mechanisms.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models. 

The Door Switch is an OEM component for Whirlpool laundry centers. Located inside the washer or dryer door, it regulates operational functions based on the door position.

The sensitive switch detects when the door is closed to allow cycle activation or automatically pauses the appliance when opened. Precise mechanisms ensure accurate readings cycle after cycle to prevent damage from accidental openings. 

Symptoms of a bad door switch can include: 

• Inability to start cycles until doors are repeatedly opened/closed
• Load fails to agitate or tumble when doors closed  
• Cycles unexpectedly stop mid-operation  
• Fault codes or error displays for door issues

Compatible with Maytag, KitchenAid, Jenn-Air, and some Kenmore laundry centers as well.

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

Rubber seal that creates a watertight barrier between the appliance door and tub, helping prevent leaks and keep moisture and debris out. Replace a worn or torn seal to restore proper sealing and reduce the risk of water damage. What it does:

• Forms a flexible, leak-resistant seal around the door/tub opening to keep water and detergent inside.
• Helps reduce odors and debris entry by keeping the chamber closed from outside contaminants.
• Common symptoms: visible cracks or tears, water pooling under the appliance, persistent dampness or mold around the door area.
• Restores reliable sealing to help protect floors and nearby cabinetry from moisture damage.

• Disconnect power and shut off the water supply before beginning any repairs.
• Remove the old gasket carefully, clean the mounting surface, and inspect for any damage before installing the new seal.
• Seat the new seal fully and evenly around the opening to ensure a watertight fit; check the appliance for leaks after first cycle.

Dryer Vent Test Kit ensures your dryer's vent system is operating properly. Kit includes two tests depending on the location of your dryer's lint screen: One for the lint screen in the top of your dryer, and one for the lint screen in the front of your dryer. Instructions included.

This hinge pin assembly provides the pivot point for your door, keeping it aligned on the hinge and allowing smooth opening and closing. Replacing a worn pin restores proper door movement and helps maintain a reliable seal.

• Creates the pivot for the door to rotate smoothly on the hinge
• Maintains door height and alignment for consistent gasket contact
• Helps prevent sagging, rubbing, or gaps that can affect sealing
• Common symptoms include clicking/popping at the hinge, door wobble, or difficulty closing

• Disconnect power and support the door before servicing
• Note hinge orientation and the placement of any spacers/washers; transfer as needed
• Secure fasteners without overtightening to avoid binding
• After installation, verify door alignment and gasket seal

The Door Seal is an OEM component specifically designed for Whirlpool dryers. It works to create an airtight seal between the dryer door opening and drum interior. During operation, heated air and moisture are contained within the drum thanks to this crucial seal. 

Symptoms of a worn door seal include:

• Increased drying time due to air leaks
• Clothes not drying completely before end of cycle  
• Excess humidity escaping into home
• Discoloration or residue buildup on door glass

Causes of failure are normal wear and compression over extended use, or damage from improper door closure. A worn seal degrades efficiency and performance of the dryer.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This replacement screw secures appliance components in their intended positions. Swapping a missing, stripped, or corroded screw helps stop rattles and keeps panels, brackets, and internal parts tight for reliable operation.

• Fastens panels, brackets, or internal parts where specified by your model
• Helps reduce vibration and rattling caused by loose hardware
• Restores alignment when an original screw is missing or damaged
• Replace if threads are stripped, head is rounded, or corrosion is present

• Disconnect power and shut off water or gas before service
• Verify the exact location using your model's parts diagram/IPL
• Start threads by hand to avoid cross-threading; tighten only until snug
• Reuse any original washers, clips, or spacers if present

This bulkhead is the front interior panel that supports the drum and helps direct dryer airflow for efficient tumbling and exhaust. It restores proper drum alignment and airflow when the original panel is worn or damaged. What it does:

• Provides a stable mounting surface for the drum and front bearing/glide assembly
• Helps channel air from the drum to the exhaust path for consistent drying
• Prevents drum wobble and rubbing that can cause noise or fabric wear
• Reduces air leaks and hot spots that can extend dry times or trigger heat issues

• One bulkhead panel

• Disconnect power and venting before beginning any repair
• Removing the front panel and drum is typically required to access and replace the bulkhead
• Inspect drum seals, rollers, and bearings while the dryer is open; replace any worn components
• Use appropriate tools and follow OEM instructions.

This screw is a genuine replacement fastener used to secure appliance panels and components for a reliable fit. It restores proper fastening where original screws are missing, stripped, or damaged. What it does:

• Fastens panels, trim, brackets or small components to keep parts aligned and secure
• Replaces missing or damaged screws that can cause loose panels or rattling
• Restores proper clamping force to prevent movement and wear on adjacent parts
• Matches OEM function and fit when the correct part number is used

• Disconnect power and water before servicing the appliance
• Use the correct driver to engage the head cleanly and avoid stripping
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic

This magnet assembly secures the washer lid in the closed position so the machine can run safely and reliably. Replaces a worn or broken lid catch magnet to restore proper lid engagement. What it does:

• Holds the lid closed by providing magnetic retention at the lid catch
• Helps the washer detect a closed lid and complete normal cycles
• Commonly replaced when the lid doesn't stay shut or the lid feels loose
• Prevents intermittent stoppage caused by poor lid engagement

• One magnet assembly

• Disconnect power before starting any repair to avoid shock or injury
• Access may require removing the top panel or lid trim; keep fasteners organized
• Inspect surrounding plastic catch for wear and replace if damaged