Whirlpool Gmc305pds08 Parts

I am a 78year old woman and 40 years ago I replaced the belt on a dryer but could not even consider such a feat today. I ordered the parts from you on line and also found the video that you very nicely have attached to the site and I saved this under my favorites. The baffles arrived within 3 days and due to my age was unaware that dryers now come in two sizes and the ones I ordered were for the smaller but same model. I worked with a very nice customer service agent on line who got me the... Read more

Replaced It With New One Read more

Don't bend the glass even a little! I made the mistake of laying mine on the handle face down when reinstalling the handle because the screws fell out and I bent the glass slightly when tightening the screws. Boom, it shattered in a million pieces. I instantly went to AppliancePartsPros.com to find a replacement. Ordering was easy as usual, shipment arrived quickly, and the door was packed perfectly. I removed the old door from the oven by releasing the hinges and lifting it out. To avoid... Read more

I was able to order new hinge receiver brackets for the door. The repair was not that bad. I just had to take off the lower door, take the two trim pieces off the sides and unscrew the screws holding the oven into the face of the cabinet. Then slide it out about halfway and put a step stool under the front to keep it from tipping over. Then it was just a matter of taking off everything around the sides until I could take the brackets off, put the new brackets on, and put everything back... Read more

I was able to order new hinge receiver brackets for the door. The repair was not that bad. I just had to take off the lower door, take the two trim pieces off the sides and unscrew the screws holding the oven into the face of the cabinet. Then slide it out about halfway and put a step stool under the front to keep it from tipping over. Then it was just a matter of taking off everything around the sides until I could take the brackets off, put the new brackets on, and put everything back... Read more

Replaced glass and missing screws. Hardest part was removing the old glass because of the double sided tape. Read more

Took off the door. Found that one of the Hinges was bent. Replaced the hinge and the door works perfectly. Pretty easy replacement - there were a total of 8 screws to take off and on. Pretty straight forward once you get the door off the oven! Read more

I read up on others with this problem of microwave-wall oven combination Whirlpool Gold. We live in a very rural area and were not able to get ANYONE to service it - had 2 companies come out to inspect but they never returned. I have wonderful news! We replaced the fuse, bus fuse, and light bulb (quit working 2 years ago) and all is working. Thanks for the information and for the part diagram. Couldn't have done it without you. Read more

The door hinge latches were bent, which made it difficult to remove the door and re-insert. The door hinge design was changed from a pin insert to a latch from the previous model. Unfortunately, the latch on the 24 inch oven is thin and easily bent, which is likely the source of the problem. I purchased spare door hinges to facilitate re-installing the oven door should I ever have problems with removing and inserting the door again. Read more

Replaced myself. Read more

Studied schematics and watched many on-line videos. Did some electrical checks with VOM (Volt/Ohm Meter). Determined that control panel thermal fuse attached to back of control panel had opened due to high temp. Determined that the upper oven thermal fuse on back of oven had opened due to high temp. Determined that transformer that supplies power to lights was bad (open primary). Removed control panel circuit board and had it repaired/verified good. Faulty control panel was the reason that oven... Read more

Ordered the right screw and screwed it in. Door now properly secured. Read more

Replaced it with the video listed..Maytag Atlantis dryer was not heating. Checked all components inside dryer, thermostat, coils, etc. All check out ok ......last thing I checked was the terminal. It was burned out. Quick video on your website was awesome! THANK YOU for the service, and the ease of ordering parts. LOVE THIS SITE! Read more

I measured the resistance between the two connectors on the magnetron: should be close to zero ohms and it was. I measured between the same connectors and the metal case: should be mega ohms, it was 15k ohms. That is a bad, partly shorted unit. I also checked the resistance of the thermal cut off, which should be zero but was 10 ohms so I replaced. The HV diode is checked with a 9 V battery (YouTube checking microwave HV diode) and it too was bad. Make sure to take pictures as you disassemble... Read more