Whirlpool Wfw72hedw Parts

This replacement screw secures appliance components and panels so they stay aligned and rattle-free during operation. Replace stripped, missing, or corroded hardware to restore a tight fit and dependable performance. What it does

• Fastens brackets, panels, and internal sub-assemblies in the appliance
• Helps maintain alignment to reduce vibration and rattling
• Replaces missing, rusted, or stripped screws that no longer hold
• Useful when a part won't mount securely or a screw backs out during use

• One screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Compare to the original for length and thread style for the location
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; if the mounting hole or clip is worn, replace it

This replacement filter traps debris and contaminants within your appliance's system to help protect internal components and maintain proper performance. Swapping a clogged or damaged filter can restore flow/airflow, reduce odors and buildup, and support efficient operation. What it does:

• Captures grease, lint, dust, or food particles to prevent recirculation and protect internal parts
• Supports proper airflow or fluid flow for ventilation, circulation, or drainage
• Helps minimize odors and residue caused by a saturated filter
• Typical signs it's due: visible tears/warping, heavy buildup, restricted airflow/venting, lingering odors

• 1 filter

• Disconnect power before servicing and allow any hot surfaces to cool
• Note the filter's orientation and any tabs/clips; install the new filter the same way
• Clean the surrounding housing or channel before installation
• Do not operate the appliance without required filter(s); follow your model's maintenance schedule

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

Color: Grey

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Contains two, six foot long braided hoses with 90 degree ends.

This RFI noise filter conditions the AC power entering your microwave, reducing electrical interference and helping protect and stabilize the control and power circuits. Replace it if the unit is dead or trips a breaker when starting.

• Filters radio-frequency/electromagnetic noise on the incoming AC line
• Helps stabilize power to the control, relays, lights, and fans
• Failure may cause no display or intermittent loss of power
• A shorted filter may blow the line fuse or trip the household breaker when plugged in or when Start is pressed

• Disconnect power by unplugging the microwave or switching off the dedicated circuit breaker
• For over-the-range units, remove the microwave from the wall to safely access internal components
• Label and transfer wires to matching terminals; mount the filter securely and route wiring away from sharp edges

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

This is a formed hose used inside the appliance to route flow between components and maintain a sealed path. Replacing a worn or damaged hose helps stop leaks and restores proper operation and circulation.

• Directs flow between specific components as designed by the manufacturer
• Wear, heat, vibration, or age can cause cracking, hardening, or kinking
• Inspect routing and clamps; a loose connection can mimic hose failure

• Disconnect power and, if applicable, shut off water supply before servicing
• Have towels/containers ready for residual water; work in a dry area
• Note hose routing and clamp positions; transfer and secure clamps as required
• Fully seat hose on fittings and check for leaks with a short test cycle

This replacement screw secures panels, brackets, and internal components in your appliance. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps keep parts properly aligned and protected during operation.

• Fastens appliance panels, brackets, and hardware in the designated locations
• Replaces missing, stripped, or corroded fasteners
• Helps reduce vibration noise and looseness from unsecured parts
• Restores proper fit and alignment after service or reassembly

• Disconnect power; turn off water supply before servicing
• Match the screw to the original location and replace one at a time to maintain alignment
• Use the correct driver; tighten snugly without overtightening to avoid stripping metal or cracking plastics
• If threads in the mating hole are damaged, repair/replace the clip or insert as specified in the service manual

This replacement handle restores a secure, comfortable grip so you can open and close your appliance with confidence. It's designed to replace a cracked, loose, or missing handle and bring back safe, reliable everyday operation.

• Provides the grip point to open and close the unit
• Restores function and appearance when the original handle is damaged or missing
• Typical symptoms include a loose/wobbly feel, visible cracks, or the handle separating from the door/panel

• Disconnect power to the appliance before starting; shut off gas or water if applicable
• Protect the finish and support the handle while removing interior fasteners
• Transfer any end caps or mounting screws from the old handle; tighten hardware evenly without overtightening
• Verify secure attachment and proper operation before returning the unit to service

This direct hose assembly routes water or drain flow to restore proper operation and stop leaks caused by cracked or worn tubing. Designed to replace a damaged hose and help prevent water damage and poor drainage. What it does:

• Directs water or drain flow between appliance components to maintain proper plumbing function.
• Stops leaks and reduces the chance of water pooling or unintended discharge from worn or cracked hoses.
• Common symptoms addressed: visible leaks, water under or around the appliance, slow or inconsistent draining.

• Disconnect power and shut off the water supply before starting any repairs.
• Inspect hose ends and connections for damage; replace clamps or seals if corroded or worn.
• Secure hose with appropriate clamps and route to avoid kinks or pinch points.
• After installation, restore power and water, run a short cycle, and check all connections for leaks.

This wire harness routes power and signals between an appliance's control and internal components to restore reliable electrical connections. Replacing a damaged harness helps stop intermittent operation and power loss for safer, more consistent performance. What it does:

• Routes power and control signals between the control board and internal components.
• Replaces frayed, cut, or burned wiring that can cause intermittent operation or component failures.
• Helps address symptoms such as loss of power to controls, unresponsive cycles, or devices that won't start.
• Prevents loose or corroded connections that can create intermittent faults.

• Always disconnect the appliance from power (unplug or switch off circuit breaker) before servicing.
• Match each connector to its mating plug and follow the OEM wiring diagram for routing and color codes.
• Secure the harness away from heat sources and moving parts; use existing clips and fasteners.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Replacement bumper that cushions appliance parts and absorbs shock to prevent rubbing, rattling and surface damage. Restores proper fit and quieter operation for components that contact cabinets, doors or panels. What it does:

• Cushions contact points to reduce noise from doors, drawers or panels.
• Prevents metal-to-metal or metal-to-surface scraping that can cause wear or cosmetic damage.
• Helps components close and seat more evenly to reduce vibration and movement.
• Common symptom fixes: eliminates rattling, stops rubbing noises, and prevents chipping or scuffing where parts meet.

• One bumper.

• High-level, tool-light replacement; usually presses into or adheres to the mounting surface.
• Disconnect power or unplug the appliance before opening panels where required.
• Inspect surrounding clips/retainers and clean the mounting area for best adhesion or fit.